Instruction: Express your intermediate answers with at least FOUR decimal places and simplify your FINAL answers up to TWO DECIMAL PLACES. BOX your FINAL ANSWERS. 2. Determine the maximum and minimum tension in the parabolic cable and the force ineach of the hangers. The girder is subjected to the uniform load and is pin connected at B.1 ft↓10 ftA10 ftB30 ft9 ft12 k/ft

Answered: Image /qna-images/answer/0f0f0e4f-015a-4a19-a250-e3df9ffb96f2.jpg

2. Determine the maximum and minimum tension in the parabolic cable and the force in each of the hangers. The girder is subjected to the uniform load and is pin connected at B. 1 ft ↓ 10 ft D -10 ft- B 30 ft 9 ft 2 k/ft

2. Determine the maximum and minimum tension in the parabolic cable and the force in each of the hangers. The girder is subjected to the uniform load and is pin connected at B. 1 ft ↓ 10 ft D -10 ft- B 30 ft 9 ft 2 k/ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 12kN HIZL= A 15kN SKN 0.5 m 1m tomt 0.5 m 1m 20 kN.m 5kN/m 44 0.5 m 1m

A: To find support reaction at point A and G

Q: Problem 2. A simply supported truss loaded as shown. Required: (1) Reaction @ supports A & C; (2)…

A: Here we will use method of joints to calculate the force in each member,in which at every joint we…

Q: Question A triangular direct runoff hydrograph due to a storm has a time base of 90 hours. The peak…

A: Given- Time base b=90 hrs, Peak flow Q=60 m3/s @ 20 hrs, Area A=300 km2,

Q: magnitude of the resultant moment (in lbf-ft) about point A of the distributed load shown below. F…

Q: The homogeneous bar ABCD shown in Fig. P-114 is supported by a cable that runs from A to B around…

Q: GON JORN 10KN A ↓ B с Aum 4m 42m 2m² TUM Support xxn at B 3m ISKN 3m ROKN SKN 8kN DLE 2m 2m Apm tin…

Q: If the shear force in a portion of a beam is constant and positive, the bending moment in this same…

A: Example: If the shear force in a portion of DB is constant and positive, the bending moment in this…

Q: Determine the state of stress at Point E (on beam and cross section); represent those stress states…

A: Given : Determine the state of stress at point E ?

Q: Describe how wood can be attacked by fungi.

A: Fungal attack on the wood: The presence of moisture content in the wood will be the reason for…

Q: 200+00 and elevation 150.00m above the sea level. The centerline of the roadway must clear a pip…

A: According to given data A vertical curve joins a -0.5% grade to a +1.0% grade. The VPI of the…

Q: A Standard Proctor Test was completed according to Method A described in Chapter 12. The following…

A: Standard Proctor test: By eliminating air spaces, compaction densifies soil by making it more…

Q: samples shows w-14.6%, G intractor compli

A: Given: Mean value of test sample shows, ω=14.61=0.146Gs=2.81γ=18.2 kN/m3

Q: FRONT VIEW RIGHT SIDE VIEW FRONT VIEW RIGHT SIDE VIEW

Q: f L A I →∞ tim

Q: 7-21* A steel pipe with an outside diameter of 4 in. and an insid diameter of 3 in. is simply…

A: Given : We have an outside diameter = 4 inches Inside diameter = 3 inches Determine : a) The…

Q: a) 8 kips. 16²7 36 kips 16' E B 24 kips 12 12² ↓

A: As per Bartleby's guidelines we are supposed to answer only first question. Kindly repost other…

Q: 28. Based on the report provided from the study of Nishiyama that focuses on mechanical properties…

A: This question related to the Design of Steel Structure from Civil Engineering.

Q: Tail 3m 1+1 18 M/ GIZ Во qm M2 W G& BF BF Xx 18m 11,000 kg Tim 1.8m

Q: Question 1 Calculate the magnitude of the resultant moment (in lb-ft) due to the 200-lb and 50-lb…

A: Given Data Find moment about point-A due to 200 lb and 50 lb.

Q: Given the following data: SSD = 430’ G = +3% Tpr = 2.5 sec Will the speed/velocity be acceptable…

Q: 150-mm diameter Section A (a) 100-mm diameter 30° Section B

A: Energy is lost when it is changed from one form to another, transported from one location to…

Q: 48. The steel properties include very high strength, extreme hardness and resistance to wear, and…

A: This question is related to the Design steel structure from Civil Engineering.

Q: The steel bar AB has a diameter of 30mm and is connected to the brass bar BC. The two bars are fixed…

Q: The two forces are equivalent to a force R that has a line of action passing through point A.…

A: Given: From the figure, Force in X-directionFx=100 N Force in Y-directionFy=90 N To find: (1)…

Q: Determine the smallest horizontal force P required to lift the 450-lb crate. The coefficient of…

A: Given : Coefficient of static friction = 0.25 Load to be lifted = 450 lb Determine the smallest…

Q: Assume you are an observer standing at a point on a three lane race track. All vehicles in lane 1…

A: According to given data Assume you are an observer standing at a point on a three lane race track.…

Q: Gravity wall- Determine b (wall width) for both sliding and overturning. 3² - 0² -15' 1 -65-23,000…

A: Answer For wall 1(Top left) Let us first draw the free body diagram of forces acting on the dam W…

Q: 10-1 A simple beam AB supports five equally spaced loads P (see figure). Using superposition method,…

Q: atch Reactor with a volume of 11.859 m³ is being used to treat liquid waste from a small seafood…

A: According to given data Every week 1.461 kg of waste is added to the reactor with water, so that…

Q: Q: In the figure below, the depth of excavation required to form a cutting at 20 m intervals are…

A: Given Width of roadways = 5 m Length of roadways = 80 m Intervals of depth measurement, h = 20 m…

Q: The degree of static indeterminacy of the plane frame as shown in figure is Hinge D

A: Given- A plane frame is given, It is needed to find the value of degree of static indeterminacy Ds.

Q: The two forces are equivalent to a force R that has a line of action passing through point A.…

A: From fig we can understand that, the point A should be at lower right point. Because we can…

Q: What will be the theoretical maximum capacity (to nearest 10 units) for a single lane of highways…

A: Given data: Speed of the traffic stream, v = 40 kmph Theoretical maximum capacity, C =?

Q: List the advantages and disadvantages between window wall and curtain wall systems?

A: Window wall and Curtain wall systems- A window wall system is put inside the slab edge since it only…

Q: For the beam shown (E = 200 GPa, A=12 cm², I-9 cm¹), determine: a) Reactions at A and C. b) Draw the…

Q: Q: Using a digital laser level instrument, the following staff readings were observed via an open…

A: Here we have given a open loop and we will use rise and fall method to calculate the RL's of each…

Q: -tested in an uncons ssure of 200 kPa and

A: Given: Effective shear strength parameters c'=20 kPaθ'=25o Cell pressure is 200 kPa Principal stress…

Q: Draw the Axial Force Diagram (NFD), Shear Force Diagram (SFD) and Bending Moment Diagram (BMD) for…

A: Given data : Determinate beam with roller and pinned support at a and b Find : NFD , SFD and BMD…

Q: Determine the force in members BC, CF, and FE. State if the members are in tension or compression.

A: Given data : Using Method of section we have to determine forces in members BC, CF and FE ? Concept…

Q: can you answer both parts

A: To find support reaction at point A and B

Q: CE A 1.5 m- Wo = 8 kN/m P₁ = 20 KN -1.5 m- D P₂ = 6 KN B -1 m1 m E

Q: A sluice gate in a 2.0 m wide horizontal rectangular channel is discharging freely. If the depths of…

A: Given Data Width of channel (B) = 2m Find discharge in channel when 1. Neglecting energy losses…

Q: did you come up with 100 k-ft for the BMD? I'm probobly missing it but I'm unsure of how you got

Q: -3.6 m- PROB. 17.4 1.5 m steel E = 200 × 10 kPa. Determine the capacity P of the boom. Use the Euler…

Q: Which type of internal bending moment causes the following bending stresses?

A: Context: Internal bending moment

Q: A vehicle is composed of a Single Axle Single Tyre (SAST) which has a load of 240 kN and a Tandem…

A: Answer We are given Single Axle Single Tyre (SAST) load 240 KN Tandem Axle Dual Tyre(TADT) load…

Q: A prestressed concrete beam of effective span 16 m is of rectangular section 400 mm wide by 1200 mm…

A: Given Data : fpu=1700 N/mm2 fcu=60 N/mm2 Aps=3300 mm2 fpe=910 N/mm2 L=16 m b=400 m d=870 m Ld=18.39…

Q: For the rigid frame shown, calculate the horizontal deflection at point C. Members have the same…

A: E=210 GPa=210 x 106 kNm2I=1440 x 104 cm4 = 0.1440 m4EI=30.24 x 106 kN.m2Angle that BC makes with…

Q: Determine the cross-sectional areas of members AG, BC, and CE for the truss shown in Fig. The…

A: Given : Allowable stress = 20 ksi in tension Allowable stress = 14 ksi in compression Determine…

Q: The figure below shows a vertical circular gate in a 3-m diameter tunnel with water on one side and…

A: Given : Diameter of tunnel = 3 m

Question

Instruction: Express your intermediate answers with at least FOUR decimal places and simplify your FINAL answers up to TWO DECIMAL PLACES. BOX your FINAL ANSWERS.

2. Determine the maximum and minimum tension in the parabolic cable and the force in
each of the hangers. The girder is subjected to the uniform load and is pin connected at B.
1 ft
↓
10 ft
A
10 ft
B
30 ft
9 ft
12 k/ft

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The trusses are pin connected and suspended fromthe parabolic cable. Determine the maximum force in thecable when the structure is subjected to the loading shown.The support at A is a pin and C is a rocker.
5-70. Determine the tension in cables BD and CD and the x, y, z components of reaction at the ball-and-socket joint at A. 3m 300 N B 1.5 m 0.5 m Im
8-21 The offset link has a width of w = 200 mm and a thick- ness of 40 mm. If the allowable normal stress is σallow 75 MPa, determine the maximum load P that can be applied to the cables. P 50 mm P
The tension of cable AC is 110 N. Determine the mass of the crate at point E. g=9.81 m/s² 3m E -3m 6m B 2m y
The horizontal beam is supported by cables at its ends. Determine the required force of the cable at A and B so that if the beam remains in the horizontal position. 800 N 200 N A „C D B -2 m -2 m - -2 m -
10. Determine the force in each member of the truss. (F6-6).
Determine the compressive force along the leg AB Determine the compressive force along the leg CB. Determine the tension in the winch cable DB
The Fink truss is supported by a hinge at A and by rollers on a 2 to 3 slope at G. The bracing bars are normal to the inclined members at their midnoints. The wind loads are perpendicular to AC. Determine all bar forces. 1580 Ib 3160 Ib D I880 Ih B F 12' G 8400 Ib 18,000 Ih 12'
*5-16. Determine the tension in the cable and the horizontal and vertical components of reaction of the pin A. The pulley at D is frictionless and the cylinder weighs 80 lb. D A B C 5 ft 5 ft -3 ft- Prob. 5-16
Determine the maximum and minimum tension inthe parabolic cable and the force in each of the hangers. Thegirder is subjected to the uniform load and is pin connectedat B
A drawbridge is being raised by a cable EI. The four joint loadings shown result from the weight of the roadway Determine the force in members EF, DE, DF, CD, and FG. H 6 kips Answers: EF= DE=> DF = 10 CD= FG = X X3 X3 G 16 10 B 12 kips -10 F 57 E C 12 kips kips kips kips kips kips T 6' D 6 kips
2. Determine the force in each member of the truss. IHG F D 2a L6@a²6a