2. A simply supported beam, 4 in wide by 8 in high and 120 in long is subjected to a concentrated load left of the 1600-lb load acting on the simple beam AB shown in the figure. Draw the Shear-Moment Diagram of the beam, find the maximum fiber stress in kPa and the stress in a fiber located 1 in from the top of the beam at midspan. 800 lb 1600 lb A В 30 in.→< 60 in. +30 in.→ 120 in.

2. A simply supported beam, 4 in wide by 8 in high and 120 in long is subjected to a concentrated load left of the 1600-lb load acting on the simple beam AB shown in the figure. Draw the Shear-Moment Diagram of the beam, find the maximum fiber stress in kPa and the stress in a fiber located 1 in from the top of the beam at midspan. 800 lb 1600 lb A В 30 in.→< 60 in. +30 in.→ 120 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. Determine the shearing stress in each of the four walls of a portion of a structural aluminum tubing when it is subjected to a torque of 3 kN-m assuming a uniform wall thickness of 4mm. A ( 51 ) mm В 100 mm 100 mm C D ( 51 ) mm
A uniform steel shaft has a diameter of 50 mm is fixed at ends A and B. The shear modulus of steel is 75 GPa.d) Calculate the maximum shear stress in the system in MPa. You will have to look at each individual piece of the system, so clearly indicate which segment has the maximum stress.[Ans. to check: τmax = 8.15 MPa]e) Calculate the total rotation of the shaft at point C in radians.
For a beam with the cross-section shown and loaded as shown, find the magnitude of the maximum bending stress in the beam. The moment of inertia about the z axis is 257,633 mm4, the centroid of the section is located 19.67 mm above the bottom surface of the beam, and M = 415 N-m. M (A) 66.1 MPa B) 35.9 MPa C) 48.9 MPa (D) 58.1 MPa (E) 52.1 MPa N M X 8 mm N 8 mm į 50 mm 8 mm ... 50 mm
A symmetrical beam of length 300 mm is loaded with a force of 414 N downwards (positive z) and has the following equation for the vertical displacement: w (2) = - + F 48 %3D The value of E is 200,000 Nmm² and the values of ly is 20 x 10° mm“ The maximum value of z for the beam cross section is +20 mm What is the maximum tensile stress in the beam at the point when x = 86 mm?
(c) A thin, triangular plate ABC is uniformly deformed into a shape ABC', as shown by the dashed lines in the figure. Calculate (i) The normal strain along the centreline OC; (ii) The normal strain along the edge AC; and (iii) The shearing strain between the edges AC and BC. b 0-1 b B 90° 10.001b
The cantilever T- beam is loaded as shown in the figure. Ti 80 mm 40 kN/m NA --- 120 mm 2.0 m INA = 30x105 mm What is the value of fleure stress in a distance 1.20 m from the free end at the topmost fiber of the beam section?
A beam ABC with an overhang from B toC supports a uniform load of 200 lb/ft throughout itslength (see figure). The beam is a channel section withdimensions as shown in the figure. The moment of inertiaabout the z axis (the neutral axis) equals 8.13 in4.(a) Calculate the maximum tensile stress σt andmaximum compressive stress σc due to theuniform load.(b) Find the required span length a that results inthe ratio of larger to smaller compressive stressbeing equal to the ratio of larger to smaller tensilestress for the beam. Assume that the totallength L =a + b = 18 ft remains unchanged.
35 The maximum tensile stress developed in a rectangular beam loaded transversely downward occurs at: A. extreme top fiber B. extreme bottom fiber C. neutral axis D. anywhere in the section
A rigid plate C is used to transfer a 20-kip load P to a steel (E = 30,000 ksi) rod A and to an aluminum alloy (E = 10,000 ksi) pipe B as shown. The supports at the top of the rod and the bottom of the pipe are rigid, and the materials were unstressed before the load was applied. The cross-sectional areas of rods A and pipe B are 0.80 in2 and 3.00 in2 respectively. Determine The normal stress in rod A in ksi, The normal stress in pipe B in ksi and The displacement of plate C in inches. Note: Draw the Free Body Diagram, include the units/dimensions, use the proper formula and round-off all the answers and final answers to 5 decimal places.
(Problems No. 1 - 3) The state plane stress at a point is represented by the stress element below. Determine the stresses acting on an element oriented 30 degree counterclockwise respect to the original element. Calculate the shearing stress at the xy-face 60 MPa 20 MPa 90 MPa O a. -55 MPa O b. 65 MPa 55 MPa O d. -65 MPa
Problem 2 The rigid bar is plnned at A and held by two flexible bars at E and C. The load P Is applled at B. The two flexible bars FE and DC each have a diameter of 1 In. The flexible bars are elastic- perfectly plastic with a yleld stress equal to 20 ksl and a yleld strain of 0.001. Determine the following: The load R, at first yleld and the corresponding deflection at B, &, The ultimate load Pu and the corresponding deflection du The permanent deflection and residual stresses in each rod if the ultimate load is removed Construct P - A curve showing yield, ultimate and permanent deformation o (ksi) 1 ft E F 1 ft1 ft 20 B P e (in./in.) 0.001 1 ft D 2 ft 1 ft A
In the figure below, at section n-n (x = 4m from point A) determine the shearing stress at a on the cross-section of the beam 3m 4m 20kN/m 3m 3m 100mm 100mm 400mm 400mm