2. A concrete post 3.50 meters high with cross sectional dimensions of 30 cm. x 30 cm. is supported by a footing slab 20 cm. thick by 1.20 m. square. Using class "B" concrete, find the quantity of cement, sand, and gravel if there are 24 posts of the same size. 30cmk- 3.50 meters Column height 1.20 m 30cm 20cm 1.20 m 1.20 m

2. A concrete post 3.50 meters high with cross sectional dimensions of 30 cm. x 30 cm. is supported by a footing slab 20 cm. thick by 1.20 m. square. Using class "B" concrete, find the quantity of cement, sand, and gravel if there are 24 posts of the same size. 30cmk- 3.50 meters Column height 1.20 m 30cm 20cm 1.20 m 1.20 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Load = 3000 lb Q:Find Stresses at: Section A-B & Section D-C "18.0"- "5,5" Plain Concrete: D Compressive Strength : 280 (Psi) "12.0"- "0.5"-
Give full explanation Awall form 14 ft high is filled with 160 lb per cu ft concrete at a tem perature of 70°F. The concrete is Type I without a retarder. Concrete will be placed with normal internal vibration to a depth of less than 4 ft. The rate of placement is 5 ft per hr. From Table 1, the value of Cw is 1.1 and from Table 2 the value of Cc is 1.0. The rate of placement is less than 7 ft per hr and the place ment height does not exceed 14 ft so calculate the lateral pressure by using appropriate formula.
A rectangular footing 23 m x 32 m x 0.34 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 341 kN LL = 216 kN fc = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the nominal punching shear stress in the slab Write your final answer with 2 decimal places if the unit is MPA
Problem No. 3A beam 200x450mm is reinforced by 2-32mm diameter rebar. Assume Cc-50mm, stirrups-10mm, fc'-21Mpa and fy-415Mpa. Calculate the following. 17. Calculate the strain of the steel reinforcement O 0.00182 O 0.00201 O 0.00224 O 000391 O 0.00577
A rectangular beam has a width of 300mm and an effective depth of 537.50 mm to the centroid of tension steel bars. Tension reinforcement consists of 6 – 28mm dia in two rows, compression reinforcement consists of 2 – 22mm dia, fc’ = 27.6MPa, fy = 414.7MPa, d’ = 60mm, L = 4m, the Unit weight of concrete is 24.56kN/cu.m If the beam is simply supported carrying a uniformly distributed dead load of 10kN/m, a uniformly distributed live load of 5kN/m, the safe concentrated live load that it could carry acting at the midspan is _____kN.
A rectangular beam has a width of 300mm and an effective depth of 537.50 mm to the centroid of tension steel bars. Tension reinforcement consists of 6 – 28mm dia in two rows, compression reinforcement consists of 2 – 22mm dia, fc’ = 27.6MPa, fy = 414.7MPa, d’ = 60mm, L = 4m, the Unit weight of concrete is 24.56kN/cu.m If the beam is simply supported carrying a uniformly distributed dead load of 20kN/m, concentrated live loads of 30kN acting at third points, the additional uniformly distributed live load that it could carry is _____kN/m.
Provide solution and illustrations. Use three decimal places A rectangular reinforced concrete beam exposed to weather has a width of 300 mm and a total depth of 600 mm. The diameter of the bar to be used for reinforcement is 16 mm. fc’= 31 Mpa and fy = 276 Mpa. Determine the required number of bars for reinforcement.
H.W: Draw a construction plan for this form.. Two - Way Slab Design slab for the floor beam system shown All colunns 300 300 mm All beams = 300 * 600 mm Live load 5.1 KN/m Dead load= 0.785 KN/m² +slab weight+ tiling 4 cm = 25 MPa fy 400 MPa With brick wall around the perimeter of 1.2 m in height and 0.25 m in width 5.8m 5.8m 5.8m 7.25m 7.25m 7.25m
20. Determine the nominal load when the concrete strain of 0.003 and tensile steel strain is 0.002075. A. 1090 kN B. 1554 kN C. 1168 kN D. 1401 kN
Example 2 Determine the design ultimate moment of resistance of the following beam : Prestressing tendons = 1860 N/mm? Section Properties A = 213000 mm2 I = 13.19 x 10° mm4 f, pu Ym = 1.15 = 195 kN/mm2 ps e = 325 mm = 845 mm? Aps P. = 880 kN d = 700 mm 400 b; = = 400 mm %3D e h = 200 mm 200 Concrete b. = 150 mm = 40 N/mm2 %3D 750 150 = 1.5 Ec = 28.0 kN/mm2 %3D 200
1- For the floor system shown in Figure below, support service live load 4KN / (m ^ 2) and service dead load 5KN / (m ^ 2) Answer the flowing. Classify the floor system into one way or two-way solid slab. 2- What is the minimun slab thickness that should be used to control deflection and shear requirement ? 3- By using Ø 12 mm rebar, what is the required positive and nagative reinforcement? 4- Sketch the detail of reinforcement. Use : fy = 400Mpa , f c ^ prime =30 Mpa 6.00 m 6.00 m6.00 m 3.00 m 0.30 m АB 3.00 m 3.00 m
Fina the safest value of load "P' for the beam loaded shown. fo' = 35MP.. Use GRADE 420 steel ber ana n=10. The answer is KN. Assume unit weignt of concrete = 24 kn/cu.m. tooit oot 3m 2m 100 200 10 3P 70 200 2-20 mm BERM 330 4-32 mm 300 DIMENSIONS ARE IN "MM"