2. A 36, 60 Hz, 6 pole, wye-connected induction motor is rated at 600 hp (1 hp = 746 W) and 800 V. The parameters of the equivalent circuit are R1 = 0.08 N X1 = 0.15 N Xm = 16 N R2 = 0.04 N X2 = 0.08 N The friction and windage losses are 0.6 kW. You may ignore the core losses for this problem. For a slip of 3%, determine the following, assuming the line-neutral terminal voltage angle ZVi is zero: (a) Line current and power factor (b) Air-gap power

2. A 36, 60 Hz, 6 pole, wye-connected induction motor is rated at 600 hp (1 hp = 746 W) and 800 V. The parameters of the equivalent circuit are R1 = 0.08 N X1 = 0.15 N Xm = 16 N R2 = 0.04 N X2 = 0.08 N The friction and windage losses are 0.6 kW. You may ignore the core losses for this problem. For a slip of 3%, determine the following, assuming the line-neutral terminal voltage angle ZVi is zero: (a) Line current and power factor (b) Air-gap power

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

If two 3-phase induction machines are mechanically coupled with each other. The two machines are supplied by 50 Hz and 60 Hz, respectively. the speed of the combination of both machines will be:
6. Home Works: a) The figure below shows the per-phase equivalent circuit of a two- pole three-phase induction motor operating at 50 Hz. The voltage (E1) across the magnetizing inductance is 210 V, and the slip (s) is 0.05. What is the developed torque produced by the motor ? 0.04 0 jo.22 Q j0.22 0 j6.28 NE E1 0.05 0
3. What are the various losses in an induction motor? On whatfactors do they depend?
1. The operation of Commutator in DC Motor is * O a) to convert dc to ac O b) to convert ac to dc O c) to convert fixed dc to variable dc O reverse the current direction in the rotating windings each half turn
6. Home Works: a) The figure below shows the per-phase equivalent circuit of a two- pole three-phase induction motor operating at 50 Hz. The voltage (E1) across the magnetizing inductance is 210 V, and the slip (s) is 0.05. What is the developed torque produced by the motor ? 0.04 N jo.22 Q j0.22 0 0.05 0 j6.28 NE E1 V
8. A 3-phase induction motor is running at 2% slip. If the input to rotor is 1000 W, then mechanical power developed by the motor is ............ (i) 20 W (iii) 500 W (ii) 980 W (iv) 200 W
Q9 / What are the function of brushes , pole and commutator in DC machine
What will be the operating power factor of a 3-phase induction motor, whose ratings are 230 V, 50 Hz, 120 hp, and 4-poles? Motor is operating at rated conditions with an efficiency of 92% and draws a line current of 260 A. The core loss and stator copper losses are 1710 W and 2830 W respectively. (a) 0.85 (c) 0.93 (b) 0.90 (d) 0.80
Maz a) A sinewave is having a frequency of 50 Hz and instantaneous value of 250 Volts at 1.3 milli seconds. Find D The maximum value of sinusoidal voltage waveform and i) The value of voltage at 2.1 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=100 Volts, Time period is 10 milli seconds and 0 =40 degrees. on Vp Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. a) (i) Maximnum value = a) (ii) Value of voltage at 2.1 ms = b) Angular frequency =
The terminal voltage of a 150 kW series generator is 600 V at rated load. The armature resistance is 0.06 ohms and the series field resistance is 0.04 ohms. Find generated emf.
The maximum speed of an alternator working at 60 Hz is possible when the number of poles of the machine is ........ a. 4 b. 5 c. 3 d. 2
A single-phase 111-V, 50-Hz supply is connected to a coil with 200 turns of a coil-core assembly as shown in the given figure. Find the magnitude of maximum flux in the core. 包 N