12- A furnace wall is comprised of a 200-mm thick fire clay wall with an average thermal conductivity of 0.26 W/m.K. Determine the heat loss through the wall when the inside temperature of the furnace is 1253 K and temperature outside the wall is 328 K. If the ambient air temperature is 300 K, what is the convection heat transfer coefficient of ambient?

12- A furnace wall is comprised of a 200-mm thick fire clay wall with an average thermal conductivity of 0.26 W/m.K. Determine the heat loss through the wall when the inside temperature of the furnace is 1253 K and temperature outside the wall is 328 K. If the ambient air temperature is 300 K, what is the convection heat transfer coefficient of ambient?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.6P

See similar textbooks

Similar questions

2.7 A very thin silicon chip is bonded to a 6-mm thick aluminum substrate by a 0.02-mm thick epoxy glue. Both surfaces of this chip-aluminum system are cooled by air at , where the convective heat transfer coefficient of air flow is . If the heat dissipation per unit area from the chip is under steady-state conditions, draw the thermal circuit for the system and determine the operating temperature of the chip.
2.42 A circumferential fin of rectangular cross section, 3.7-cm OD and 0.3 cm thick, surrounds a 2.5-cm- diameter tube as shown below. The fin is constructed of mild steel. Air blowing over the fin produces a heat transfer coefficient of K. If the temperatures of the base of the fin and the air are and , respectively, calculate the heat transfer rate from the fin.
1.4 To measure thermal conductivity, two similar 1-cm-thick specimens are placed in the apparatus shown in the accompanying sketch. Electric current is supplied to the guard heater, and a wattmeter shows that the power dissipation is 10 W. Thermocouples attached to the warmer and to the cooler surfaces show temperatures of 322 and 300 K, respectively. Calculate the thermal conductivity of the material at the mean temperature in W/m K. Problem 1.4
One end of a 0.3-m-long steel rod is connected to a wall at 204C. The other end is connected to a wall that is maintained at 93C. Air is blown across the rod so that a heat transfer coefficient of 17W/m2 K is maintained over the entire surface. If the diameter of the rod is 5 cm and the temperature of the air is 38C, what is the net rate of heat loss to the air?
3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the atmosphere from outer space. If its original temperature is 38°C, the effective average temperature of the atmosphere is 1093°C, and the effective heat transfer coefficient is , estimate the temperature of the shell after reentry, assuming the time of reentry is 10 min and the interior of the shell is evacuated.
The heat transfer coefficient for a gas flowing over a thin float plate 3-m long and 0.3-m wide varies with distance from the leading edge according to hc(x)=10x1/4Wm2K If the plate temperature is 170C and the gas temperature is 30C, calculate (a) the average heat transfer coefficient, (b) the rate of heat transfer between the plate and the gas, and (c) the local heat flux 2 m from the leading edge. Problem 1.18
1.51 The inner wall of a rocket motor combustion chamber receives by radiation from a gas at . The convection heat transfer coefficient between the gas and the wall is . If the inner wall of the combustion chamber is at Problem 1.51 a temperature of , determine (a) the total thermal resistance of a unit area of the wall in and (b) the heat flux. Also draw the thermal circuit.
Water at a temperature of 77C is to be evaporated slowly in a vessel. The water is in a low-pressure container surrounded by steam as shown in the sketch below. The steam is condensing at 107C. The overall heat transfer coefficient between the water and the steam is 1100W/m2K. Calculate the surface area of the container that is required to evaporate water at a rate of 0.01 kg/s. Problem 1.16
Using Table 1.4 as a guide, prepare a similar table showing the orders of magnitude of the thermal resistances of a unit area for convection between a surface and various fluids.
1.1 On a cold winter day, the outer surface of a 0.2-m-thick concrete wall of a warehouse is exposed to temperature of –5°C, while the inner surface is kept at 20°C. The thermal conductivity of the concrete is 1.2 W/m K. Determine the heat loss through the wall, which is 10-m long and 3-m high. Problem 1.1
An electronic device that internally generates 600 mW of heat has a maximum permissible operating temperature of 70C. It is to be cooled in 25C air by attaching aluminum fins with a total surface area of 12cm2. The convection heat transfer coefficient between the fins and the air is 20W/m2K. Estimate the operating temperature when the fins are attached in such a way that (a) there is a contact resistance of approximately 50 K/W between the surface of the device and the fin array and (b) there is no contact resistance (in this case, the construction of the device is more expensive). Comment on the design options.
3.5 In a ball-bearing production facility, steel balls that are each of 15 mm in diameter are annealed by first heating them to 870°C and then slowly cooling in air to 125°C. If the cooling air stream temperature is 60°C, and it has a convective heat transfer coefficient of , determine the time required for the cooling.