114 liters/second of water passes through the 30-degree elbow shaped on the side. The mass (M) of the elbow is 10 kg and its internal volume is 6 liters. The inlet cross-sectional area of the èlbow is 0.0182 m2 and the outlet cross-sectional area is 0.0081 m2. The absolute pressure at the elbow inlet is 200 kPa. Find the force and direction of this elbow on the connection point. The friction inside the pipe and the height of the pipe (in the vertical direction) must be neglected.) M= 10 kg „0.006 m² P1 = 200 kPa A = 0.0182 m? Az = 0.0081 m?

114 liters/second of water passes through the 30-degree elbow shaped on the side. The mass (M) of the elbow is 10 kg and its internal volume is 6 liters. The inlet cross-sectional area of the èlbow is 0.0182 m2 and the outlet cross-sectional area is 0.0081 m2. The absolute pressure at the elbow inlet is 200 kPa. Find the force and direction of this elbow on the connection point. The friction inside the pipe and the height of the pipe (in the vertical direction) must be neglected.) M= 10 kg „0.006 m² P1 = 200 kPa A = 0.0182 m? Az = 0.0081 m?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The diameter of a pipe changes gradually from 6 inches at A to 18 inches at B. A is 15 ft lower than B. If the pressure at A is 10 lbs per square inch and at B, 7 lbs per square inch when there are 5.0 cubic ft per second flowing, determine: a. the direction of flow. b. the frictional loss between the two points B. If in Problem 1 the direction of flow is reversed, determine the pressure at A if all other factors, including the frictional loss, remain the same. C. In Problem 1, determine the diameter of pipe at B in order that the pressure at that point will also be 10 lbs per square inch, all other factors remaining constant. D. Determine the discharge in Problem 1, assuming no frictional loss, all other conditions remaining as stated. E. What would be the difference in pressure in pounds per square inch between A and B, Problem 1, if there were 6.2 cubic ft per second flowing, neglecting friction.
The air above the liquid (S.G.=0.85) is under a pressure of 40kPa gage. The rectangular gate is 2.0m wide. a) Determine the hydrostatic force acting on the gate. b) Determine the location of the force measured from the hinge. c) Calculate the minimum value of P to hold the gate in place.
The diameter of a pipe carrying oil (s=0.92) changes gradually from 400 mm at A to 600 mm at B. Point A is 3.6 m lower than B. If the pressure at A is 70 KPa and that at B is 49 KPa when 140 L/s is flowing, determine the direction of flow; (b) the frictional loss between the two points.
1. A semi-circular gate of diameter "d" and radius "r" is submerged in a liquid and has its diameter on the liquid surface. a. Compute for the value of eccentricity if the top of the gate is 2m from the surface and radius is 2 m. b. Compute the location of the center of pressure if the top of the gate is 2m from the surface and radius is 2 m. c. Compute for the hydrostatic force on one side 4r /3n he CG. CP.
1. A semi-circular gate of diameter "d" and radius "r" is submerged in a liquid and has its diameter on the liquid surface. a. Compute for the value of eccentricity if the top of the gate is 2m from the surface and radius is 2 m. b. Compute the location of the center of pressure if the top of the gate is 2m from the surface and radius is 2 m. c. Compute for the hydrostatic force on one side 4r 13n hg CG. CP.
width of the gate is 0.5 m Determine the hydrostatic force of the liquid on the gate Determine the distance of the force from the hinge A How much force, F, applied at B. perpendicular to the gate, needed to prevent the gate from opening?
solve for the total head loss given that the pressure drop between the junction=250kPa. (f=0.02) Use 3 decimal places
# 4] The isosceles triangle gate shown in the figure is hinged at A and weighs 1000N. What is the total hydrostatic force acting on one side of the gate in kiloNewton? Locate the center of pressure from B. -.Is... 3.0m 2m 3.0m 60 B.
A vertical triangular gate with Alcohol (SG = 0.78) on one side is shown in the figure. Determine the total resultant force acting on the gate and the location of the center of pressure. +dy 3ft Unit weight of the liquid (y) Value of hbar (h) Area of the rectangular gate (A) Hydrostatic Force (F) Value of (Igx) Value of ybar (9) Location of the Hydro.Force measured from the water surface of the gate inclined (yp) Ib/ f ft ft lb fi ft ft ***answer Hydrostatic Force F on the box below:
A circular gate of radius mis - submerged in a liquid with its top edge flushed on the liquid surface. Solve for the location in meters from the surface of the total force acting on one side of the gate from the top. RADIUS = 2 UNIT WT = 16.01 1.5 2.75 3.75 2.5
7. A nozzle discharges 100 L/s with a velocity of 24 m/s and is inclined 45° downwards. The jet coming out of the nozzle strikes an unsymmetrical two-cusped vane that is moving at a velocity of 6 m/s along the horizontal plane. Half of the jet is deflected upwards 45°and the other half is deflected downwards 90°. Determine the x- and y-components of the force exerted by the jet on the vane. vane
A 90° elbow in a horizontal pipe is used to direct water flow upward at a rate of 40 kg/s. The diameter of the entire elbow is 10 cm. The elbow discharges water into the atmosphere, and thus the pressure at the exit is the local atmospheric pressure. The elevation difference between the centers of the exit and the inlet of the elbow is 50 cm. The weight of the elbow and the water in it is considered to be negligible. Determine (a) the gage pressure at the center of the inlet of the elbow and (b) the anchoring force needed to hold the elbow in place. Take the momentum flux correction factor to be 1.03 at both the inlet and the outlet. 50 cm 50 cm Water 40 kg/s