100 mL tap water is titrated with 20 mL of 0.02 M EDTA solution to determine the hardness of the water. The second 100 mL tap water is precipitated as CaC2O4 and removed by filtration and the filtrate is titrated with 8.0 mL of the same EDTA solution. What are the concentrations (as ppm) of Ca2+ (40.078

Q: A 100 ml sample of water require 20 ml of 0.02 N EDTA for titration using EBT as indicator.100 ml of…

A: Given : sample of water = 100 mL Molarity of EDTA = 0.02 M Volume of EDTA = 20 mL = 0.02 L moles of…

Q: 6. Titration of Ca²+ and Mg2+ in a 50.00-mL hard water sample required 23.65 mL of 0.01205 M EDTA. A…

A: A question based on environmental pollution that is to be accomplished.

Q: aria wants to determine the concentration of Calcium ions in water from their well. She used a 100.0…

A: Maria wants to determine the concentration of Calcium ions in water from their well. She used a…

Q: The volume of EDTA 0,0800 mol/L is required to titrate 21,70 mL of a Mg(NO3)2 solution with a…

A:

Q: . Titration of Ca²+ and Mg²+ in a 50.00-mL hard water sample required 23.65 mL of 0.01205 M EDTA. A…

A: A question based on environmental pollution that is to be accomplished.

Q: 0.75 gm of calcium carbonate is dissolved in 1 liter of distilled water. 100 ml of this standard…

A: 0.75 gm of calcium carbonate is dissolved in 1 liter of distilled water. 100 ml of this standard…

Q: A water sample that is believed to contain a maximum hardness of 100.0 ppm CaCO₃ was titrated with…

A:

Q: 3. The ethyl acetate concentration in an alcoholic solution was determined by diluting a 10.00-mL…

A:

Q: If you titrate 50 mL of a sample with 0.06 N EDTA and the titration takes 12.4 mL of EDTA to reach…

A: Hard water refers to that water which contains soluble salts of Ca2+ and Mg2+. It is not suitable…

Q: 0.15 gm of calcium carbonate is dissolved in 1 liter of distilled water. 20 ml of this standard hard…

A: Hardness  of water is due to calcium and magnesium within the water molecules. Hardness or softness…

Q: 2) In order to determine the hardness of water, 100 mL sample is taken. After neutralizing the…

A:

Q: When doing a titration, it is helpful to know approximately the volume of titrant that will be…

A: The equation to calculate the unknown value from known value is given by, M1V1=M2V2 where M is the…

Q: In the titration of 25.00 mL of a water sample, it took 20.690 mL of 4.050x 10−3 M EDTA solution to…

A: Number of moles of EDTA is determined as follows,

Q: Determine the total hardness of water (ppm CaCO3; MM: 100.09 g/mole) if 100.0mL sample of drinking…

A: Given data  Volume of EDTA = 38.41 mL Molarity of EDTA = 4.65 x 10-3 M Volume of water sample = 100…

Q: Calculate: A) the average molarity of the base. B) the standard deviation of the molarity and the…

A: Reaction between KHP and NaOH      NaOH + HOOC-C6H4-COOK -------------> NaOOC-C6H4-COOK + H2O One…

Q: 100 mL tap water is titrated with 20 mL of 0.02 M EDTA solution to determine the hardness of the…

A: Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: B. Titration Data A 100 mL Kool-Aid solution was made: 0.3210 g of Kool-Aid powder was…

A:

Q: Consider the titration of 25.00 mL of 0.03555 M Co2+ by 0.02784 M EDTA at pH 10.00. Kf is 1045.…

A: The amount of EDTA required to reach the endpoint of the titration is determined as shown below.…

Q: Chemistry An EDTA solution was prepared by dissolving 2 g of the salt in 0.500 L of water. Aliquots…

A: The molarity of MgCO3 can be calculated from its given concentration in g/L as: MMgCO3=0.7682…

Q: 0.45 gm of calcium carbonate is dissolved in 1 liter of distilled water. 50 ml of this standard…

A: 1mL of standard hard water contains 1mg of CaCO3.

Q: A 0.15mL of phenolphthalein indicator was dropped to 10.00mL of an unknown acid. Then, 52.00mL from…

A: Given: Volume of Phenolphthalein added = 0.15 mL Volume of Unknown acid = 10.00 mL Initial Volume of…

Q: A 50.0-mL water sample was determined for hardness in terms of CACO3. It required 40.0-mL of 0.0100M…

A: Given: Volume of water sample = 50.0 mL Volume of EDTA = 40.0 mL Molarity of EDTA solution = 0.01 M…

Q: 100 ml of a sample water on titration with N/50 H 2 SO 4 required 9.8 ml of the acid to…

A: The point where the color change occurs in a system is known as the Endpoint. The indicator shows…

Q: Standardization of EDTA was done using MgSO4 standard wherein a 50-mL aliquot of solution obtained…

A: Mass of MgSO4 = 0.480 g in 500 mL (0.500 L) Volume of MgSO4 = 50 mL  Volume of EDTA = 39.4 mL Mass…

Q: In the titration of 25.00 mL of a water sample, it took 20.840 mL of 4.350x 10−3 M EDTA solution to…

A: The molarity of a solution is the ratio of number of moles of a substance to the volume of solution…

Q: which of the following is the amount of magnesium in the sample in ppm? (Mg:24 g/mol)

A: Solution: Here Mg2+ ion is Complexometrically  titrated with EDTA solution. So the reaction is: Mg2+…

Q: _ In the titration why the colour changes from wine red to bue? 2_what are the harmful effects of…

A: Hello. Since more than one question has been asked, the first question shall only be answered in…

Q: An aqueous solution of 0.2100 g of a mixture containing potassium cyanide and potassium chloride…

A: Given that -  Mass of mixture of potassium cyanide, KCN and potassium chloride , KCl = 0.2100 g…

Q: 50 mL of a sample known to contain Mg+2 was taken and titrated with 0.075 M EDTA standard solution…

A: Magnesium solution is titrated complexometrically with a standard EDTA solution. we need to…

Q: You should determine how you will make the following solutions: 1- 0.8 M NAOH + 20 mM EDTA: Make 250…

A: Stock solution is a standard solution of high concentration. It can be diluted to lower…

Q: In a hardness of water determination like the one performed in this experiment, it was found that a…

A: The equation used to determine the molarity of water is written below in which M1 is the molarity of…

Q: What is the mass of pure dry CaCO3 (MW: 100.0869 g/mol) standard used in the standardization of EDTA…

A: A question based on mole concept that is to be accomplished.

Q: the molar concentration of the acetic acid solution?

A:

Q: In the titration of 25.00 mL of a water sample, it took 19.990 mL of 3.480x 10−3 M EDTA solution to…

A: we know that moles = concentration x volume (ml) / 1000 so moles of EDTA = 3.480x 10−3  * 19.990 /…

Q: Mola and Rity were tasked to analyze the acidity of a 10.0-mL fermented milk sample diluted with…

A: 10.0 mL fermented sample diluted to 250 mL 15.0 mL aliquot of the solution diluted to 50 mL 50 mL…

Q: Titration of 50.00 mL of 0.04715 M Na2C2O4 required 39.25 mL of a potassium permanganate solution.…

A: Given,                Volume of Na2C2O4 = 50.00 mL              Concentration of Na2C2O4 = 0.04715 M…

Q: Develop a titer for determining water hardness based on the following information: 6.240 mg/L Ca2+…

A: In a titration to determine the concentration of the metal ion, the EDTA combines quantitatively…

Q: In order to adjust the Potassium Permanganate solution, 0.0544g Na2C2O4 was taken and necessary…

A: The question is based on the concept of redox reactions. It involves calculation of concentration of…

Q: A water sample that is believed to contain a maximum hardness of 100.0 ppm CaCO3 was titrated with…

A: The given reaction is a complexometric titration. Parts per million or ppm is the mass of a…

Q: Iruma-kun wants to determine if the Demon Destroyer Lake had been contaminated by Fe2• from…

A: (a) Molar mass of FAS=392.1 g/mol

Q: What is the mass of pure dry CaCO3 (MW: 100.0869 g/mol) standard used in the standardization of EDTA…

A:

Q: A 0.300-g feed sample is analyzed for its protein content by the modified Kjeldahl method. If 25.0…

A:

Q: What is hardness of water? How can it be determined by using EDTA in a laboratory? In an experiment…

A: Water has a simple molecular structure. It is composed of one oxygen atom and two hydrogen atoms.…

Q: Given that the titration of Ca2+ and Mg2+ in a 50.00-mL sample of hard water required 22.35 mL of…

A:

Q: In the titration of 25.00 mL of a water sample, it took 19.040 mL of 4.965x 10−3 M EDTA solution to…

A: The problem involves only simple steps of EDTA-Ca reaction. We can calculate the number of moles of…

Q: A salt sample was analyzed for its purity. A 0.5000 g sample was dissolved in water and diluted to…

A: Given, mass of sample = 0.50 g Volume = 250 mL Volume of AgNO3= 20.0 mL Molarity of AgNO3= 0.08735 M…

Q: Calcium in powdered milk is determined by dry ashing a 1.50-g sample and then titrating the calcium…

A: mass of sample = 1.5 g Titrating volume = 10 ml mass of zinc = 0.632 g Molar mass of calcium = 40…

Q: Calculate the pCa for the titration of 50 ml of 0.02 M Ca2* at pH = 8 with 0.4 M EDTA after addition…

A: Given the solution is buffered at pH 8 At pH 8, αY4-= 4.2*10-3 Ca2+ + Y4-  ⇌ CaY2- ; Kf' = αY4-* Kf…

Q: Mola and Rity were tasked to analyze the acidity of a 10.0-mL fermented milk sample diluted with…

A:

Q: 2. 100 mL tap water is titrated with 20 mL of 0.02 M EDTA solution to dete hardness of the water.…

A: The question is based on quantitative analysis. It involves estimation of hardness content present…