1.A pair of helical gears are designed to transmit 15 kW. The teeth are 20° stub in diametral plane and have a helix angle of 45°. The pinion runs at 10 000 r.p.m. and has 80 mm pitch diameter. The gear has 320 mm pitch diameter. If the gears are made of cast steel having allowable static strength of 100 MPa; determine a suitable module and face width from static strength considerations and check the gears for wear, given ous = 618 MPa.

1.A pair of helical gears are designed to transmit 15 kW. The teeth are 20° stub in diametral plane and have a helix angle of 45°. The pinion runs at 10 000 r.p.m. and has 80 mm pitch diameter. The gear has 320 mm pitch diameter. If the gears are made of cast steel having allowable static strength of 100 MPa; determine a suitable module and face width from static strength considerations and check the gears for wear, given ous = 618 MPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A helical cast steel gear with 30o helix angle has to transmit 35 kW at 2000 rpm. If the gears has 25 teeth, find the necessary module, pitch diameters and face width for 20o full depth involute teeth. The static stress for cast steel may be taken as 100 MPa. The face width may be taken as 3 times to normal pitch. The tooth form factor is given by the expression y'= 0.154-0.912/TE, where TE represents the equivalent number of teeth. the velocity factor is given by Cv=6/(6+v), where v is the peripheral speed of the gear in m/s.
1.Please design a pair of spur gears in the milling machine. It is known that power input is 7.5kW, Ni 1450r /min, and the %3D transmission ratio is required to be u = 2.08. F1. If there is slight impact, the supplementary conditions for trial design of this pair of gears: primary selection k = 1.8, number of smaller gear teeth Z1 = 26. The allowable stress and factors for material %3D is: [0]= 600 MPa, [o„]z= 599 MPa, [0,]ı= 220 MPa, [0,]= 213 MPa. E=1.693, Z, =1898/mpa Z„ = 2.5 K =1.25 Ky =1.1 K K =1.2 На K =1.35 Y =2.65, Y = 2.28 Y =1.58 Y =1.76 %3D Fa2 Fal sa1
1) A pair of cast iron bevel gears connect two shafts at right angles. The pitch diameters of the pinion and gear are 80 mm and 100 mm respectively. The tooth profiles of the gears are of 14 1/2° composite form. The allowable static stress for both the gears is 55 MPa. If the pinion transmits 2.75 kW at 1100 r.p.m., find the module and number of teeth on each gear from the standpoint of strength and check the design from the standpoint of wear. Take surface endurance limit as 630 MPa and modulus of elasticity for cast iron as 84 kN/mm2.
1) A pair of cast iron bevel gears connect two shafts at right angles. The pitch diameters of the pinion and gear are 80 mm and 100 mm respectively. The tooth profiles of the gears are of 14 1/2° composite form. The allowable static stress for both the gears is 55 MPa. If the pinion transmits 2.75 kW at 1100 r.p.m., find the module and number of teeth on each gear from the standpoint of strength and check the design from the standpoint of wear. Take surface endurance limit as 630 MPa and modulus of elasticity for cast iron as 84 kN/mm². A0a& ENG 1222/20 nere to search
A helical cast steel gear with 30° helix angle has to transmit 35 kW at 2000 r.p.m. If the gear has 25 teeth, find the necessary module, pitch diameters and face width for 20° full depth involute teeth. The static stress for cast steel may be taken as 100 MPa. The face width may be taken as 3 times the normal pitch. The tooth form factor is given by the expression y'=0.154 – 0.912/T, where T represents the equivalent num- ber of teeth. The velocity factor is given by C, = 6 + v where v is the peripheral speed of the gear in m/s.
A helical cast steel gear with 30° helix angle has to transmit 35 kW at 2000 r.p.m. If the gear has 25 teeth, find the necessary module, pitch diameters and face width for 20° full depth involute teeth. The static stress for cast steel may be taken as 100 MPa. The face width may be taken as 3 times the normal pitch. The tooth form factor is given by the expression y'=0.154– 0.912/T; , where Tg represents the equivalent num- ber of teeth. The velocity factor is given by C, where 6 + v v is the peripheral speed of the gear in m/s.
A 70.74 hp motor turning at 2116 rpm is to deliver its power to a worm-gear reducer, whose velocity ratio is to be 25. The worm is shell type and has 3 threads; the worm and gear materials are 8 - High-test CI & High-test CI respectively. Provide the details for this pair of gears if the chosen circular pitch is 5/8. Assume Sn= 31,000 psi. For the diameter of the worm, use the proportion as provided by the equation for hell worms on page 437 of the book of FAIRES. Please answer those on the Table.
A parallel shaft helical gear consists of a 20 dts drive pinion And a 96 driven gear. Both gears have a transverse diametrical pitch of 20 dts / in, a helix angle of 25 and a pressure angle on = 20 . The face width is 4 in., AND the gears are moving at 1600 ft / min, on the pitch line. The impeller is made of steel UNSG 10180 CD and without heat treatment; the driven one is made of grade 30 cast iron. Based on flexural strength calculations, evaluate the capacity or safe maximum power at hp. Consider general industrial service, and nG = 4.
In the double-reduction gear train shown (dimensions are in inches), shaft a is driven by a motor attached by a flexible coupling attached to the overhang. The motor provides a torque of 2500 lbf-in at a speed of 1200 rpm. The gears have 20° pressure angles, with diameters shown in the figure. Use an AISI 1020 cold-drawn steel. Design Shaft CD with a design factor of 1.5 by performing the following tasks. (a) Sketch a general shaft layout, including means to locate the gears and bearings, and to transmit the torque. (b) Perform a force analysis to find the bearing reaction forces, and generate shear and bending moment diagrams. (c) Determine potential critical locations for stress design. (d) Determine critical diameters of the shaft based on fatigue and static stresses at the critical locations. (e) Make any other dimensional decisions necessary to specify all diameters and axial dimensions. Sketch the shaft to scale, showing all proposed dimensions. (f) If any of the deflections…
2. A pair of bevel gears have their shafts at right angles. The larger gear has 50 teeth of 4 diametral pitch and is made of SAE 1045 steel. The pinion has 20 teeth and runs at 850 rpm and transmit 30 hp. Determine: A. the gear diameter B. the pinion diameter C. the length of contact D. the pitch line velocity of the pinion E. the tangential force Ans. 12.5 in Ans. 5 in Ans. 6.73 in Ans. 1,112 fpm Ans. 890 lbs
In a gear set, a 36-tooth spur pinion drives a 60-tooth spur gear. The teeth of these gear are cast iron profile. The diametral pitch is 6-teeth/in, the face width si 0.5 inches, and the pressure angle is 20 degrees. Assume that the pinion transmits 10 hp at a speed of 2000 rpm. Find the pitch diameters of the gears. Find the pitch line velocity in ft/min Find the velocity factor Ky Find the tangential load in lbf Find the contact stress in kpsi, assuming CP=1960 psi.
A pair of cast iron bevel gears connects the two shafts at right angles. The pitch diameters of the pinion and gear are 80 mm and 100 mm. The shape of the gear teeth is 14½0 composite form. The allowable static stress for both gears is 55 MPa. If the pinion transmits 2.95 kW of power at 1200 rpm, determine the module and the number of teeth in each gear from the power point of view and check the design from the wear point of view. Take the surface resistance limit is 630 MPa and the modulus of elasticity for cast iron is 84 kN/mm2.