1.4-6 Maximum end-end throughput (c). Consider the scenario below where 4 TCP senders are connected to 4 receivers. The servers transmit to the receiving hosts at the fastest rate possible (ie, at the rate at which the bottleneck link between a server and its destination is operating at 100% utilization, and is fairly shared among the connections passing through that link) Server-3 Server-1 Host-1 Server-2 Host-3 Server-4 Rc Host-4 Host-2 Suppose that R-1 Gbps and Rs 300 Mbps and R is 200 Mbps. What is the TCP throughout achieved on each of the 4 connections?

1.4-6 Maximum end-end throughput (c). Consider the scenario below where 4 TCP senders are connected to 4 receivers. The servers transmit to the receiving hosts at the fastest rate possible (ie, at the rate at which the bottleneck link between a server and its destination is operating at 100% utilization, and is fairly shared among the connections passing through that link) Server-3 Server-1 Host-1 Server-2 Host-3 Server-4 Rc Host-4 Host-2 Suppose that R-1 Gbps and Rs 300 Mbps and R is 200 Mbps. What is the TCP throughout achieved on each of the 4 connections?

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter13: Internet And Distributed Application Services

Section: Chapter Questions

Problem 15VE

See similar textbooks

Similar questions

A frame containing http request is sent from Computer (A) [in whichever subnet it is now, make sure to show it in your figure], to the access point it is associated with. Draw the address fields (1, 2, and 3) of the frame travelling from Computer A to AP and the source and destination addresses of the frame travelling from AP to R1. The MAC addresses of AP1, AP2, and AP3 are M1, M2, and M3 respectively, and the Router R1’s MAC address connected to this Switch/AP is MRA. IP address values are already given, and the port addresses could also be used as given. The Router’s MAC address facing WAN side is MRW.
Consider a datagram network using 32-bit host addresses. Suppose a router has four links, numbered 0 through 3, and packets are to be forwarded to the link interfaces as follows: Destination Address Range Link Interface 11100000 00000000 00000000 00000000 through 11100000 00111111 1111111 11111111 11100000 01000000 00000000 00000000 through 11100000 01000000 1111111111111111 11100000 01000001 00000000 00000000 through 11100001 01111111 11111111 11111111 otherwise 0 1 2 3 a. Provide a forwarding table that has five entries, uses longest prefix matching, and forwards packets to the correct link interfaces.
1.4-10 Link Utilization (a). Consider the scenario below where 4 TCP senders are connected to 4 receivers. The servers transmit to the receiving hosts at the fastest rate possible (i.e., at the rate at which the bottleneck link between a server and its destination is operating at 100% utilization, and is fairly shared among the connections passing through that link). Server-1 Host-1 Server-2 Rs Rc Server-3 Rs Rc Rs R Rc Host-3 Server-4 Rs Rc Host-4 Host-2 Suppose that R = 1 Gbps and Rc is 300 Mbps and R, is 200 Mbps. Assuming that the servers are sending at their maximum rate possible, enter the link utilizations for the client links (whose rate is Rc) below. Enter your answer as a decimal, of the form 1.00 (if the utilization is 1, or 0.xx if the utilization is less than 1, rounded to the closest xx). The utilization of the client links, whose rate is Rc, is: [A]
NAT translation table LAN side addr WAN side addr 135.122.200.215 10.0.1.15 10,0.1.13 address 135.122.200.215 S: 10,0,1.27 2 D: 1 D: S: S: D: S: 10,0.1.15 D: 135.122,200,215 10.०.1.22
1.4-6 Maximum end-end throughput (e). Consider the scenario below where 4 TCP senders are connected to 4 receivers. The servers transmit to the receiving hosts at the fastest rate possible (.e. at the rate at which the bottleneck link between a server and its destination is operating at 100% utilization, and is fairly shared among the connections passing through that links Server-3 Server-1 Host-1 Server-2 Answers: R/4 R₁ Re Host-3 Host-2 Suppose that R-1 Gbps and R 300 Mbos and R, is 200 Mbps. What is the TCP throughout achieved on each of the 4 connections? 4R Server-4 st-4
TCP / IP uses the client-server communication model, in which a user or computer (a client) receives a service (such as sending a web page) from another computer (a server) on the network. In short, the TCP / IP protocol suite is classified as stateless, which means that each client request is considered new because it has nothing to do with previous requests. Being stateless, network routes are released so that they can be used continuously. Answer the following questions briefly. How does resource reservation work in the TCP / IP model? Which TCP / IP layer is responsible to reserve resources across a network using the TCP / IP model? What protocol assigns an IP address to the client connected to the Internet? Checksum is used by various protocols on the Internet, but not at the one of TCP / IP Explain.
Consider the scenario below where 4 TCP senders are connected to 4 receivers. The servers transmit to the receiving hosts at the fastest rate possible (i.e., at the rate at which the bottleneck link between a server and its destination is operating at 100% utilization, and is fairly shared among the connections passing through that link). R =1 Gbps and Rc is 300 Mbps and Rs is 400 Mbps. And that all four senders have data to send, What is the minimum value of Re that will ensure that the connections to Host-1 and Host-2 are not bottlenecked at links with capacity Rc or Re?
7.1 In IEEE 802.11, open system authentication is accomplished via a simple two-way communication. The client requests authentication, which includes the station ID, which is provided by the server (typically the MAC address). A successful or unsuccessful authentication response from the AP/router is received in response to the previous request from the client. For instance, if the client's MAC address has been expressly omitted from the AP/router setup, a failure may occur.a. What are the advantages of using this kind of authentication scheme?b. What are the security flaws in this authentication method and how may they be mitigated?
5.03-5. Dijkstra's Algorithm (3, part 5). Consider the network shown below, and Dijkstra's link-state algorithm. Suppose that Dijkstra's algorithm has been run to compute the least cost paths from node E to all other nodes. Now suppose that source node E has a packet to send to destination node A. What is the first router to which E will forward this packet on its path to A? OF (A) 3 2 4 B 8 D 10 4 E 4 2 F
Consider a client connecting to a web server via a router as shown in Fig.Q2. Client A sends a request to the server to retrieve a 7.5 Mbytes file. Given that the segment size is 50 Kbytes, the round trip time (RTT) between the server and client is 10 ms, the initial slow-start threshold is 16 and the client's buffer always has a storage space of 1 Mbytes. Assume that TCP Reno is used, there is no loss during transmission and the headers of protocols are ignored. 400 Mbps 200 Mbps 400 Mbps Link a Link b Link c Client Web Server Fig.Q2 (a) Describe how the value of sending window changes as a function of time (in units of RTT) during the whole connection time. 2.
Consider a TCP connection between Host A and Host B and the transmission of a large file from A to B. If the buffer of host B is significantly smaller than the size of the buffer of host A and the file itself, what would be outcome?
Write a Java TCP MultipleClient-Server Program for following scenario. NOTE Server Details are in the above figure Client-Server communicates continuously until the Client send Bye to the Server Use Multithreading for Multiple Clients NOTE : 1 cm = 0.39 inches 1 cm = 0.03 foot 1 cm = 0.01 meter Sample Ouput: Client Server 1 – cm to inches 2 – cm to foot 3 – cm to meter Enter length in cms (int) : 10 Received from Server 3.9 inches 1 – cm to inches 2 – cm to foot 3 – cm to meter Enter length in cms (int) : BYE Received from Server BYE Client DISCONNECTED Server Waiting for the Cline to be Connected… CONECTION ESTABLISHED Received From Client 10 cms Sent to Client 3.9 inches Received From Client BYE Sent to Client BYE HINT : When client choses 1 for cm to inches and enter 10, then the client sends the string 110 to the Server. Where the first char ‘1’ represents the cm to inches and the other 2 chars represents the 10.