1. Using one (1) drawing, point out(on the drawing) the following terms below a. Level surface b. Level Line c. Horizontal Line
Q: complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101…
A: To determine the internal loading as point E. Following is the free body diagram of the given…
Q: 10. Which of the following is correct in dimensioning a drawing?
A: 10. Dimensions should be placed in between the views.
Q: Draw orthographic views of the figure with dimensions
A: The isometric view the three dimensional which is drawn in the two dimension. The orthogonal view…
Q: is purposely to show the height of the building particularly the distance from floor line to ceiling…
A: There are various types of drawings which are drawn in order to show various details of building…
Q: Given two-view 3rd angle orthographic drawings below (Figure 1), draw top view and the new front…
A: Top view and the new front view in a section view according to the given cutting plane is shown…
Q: create (P,L,E,A,N,U,G) 2D drawing using lines, circles, curves,etc
A: Here is your drawing
Q: Write the units used by English systems to specify small areas?
A: Solution: In the English system, areas are basically given in square feet or square yards. For…
Q: What is the advantage drawing of certain outlines thicker than other lines?
A: The architectural drafting are constructed using the lines. The lines must be accurate and clear…
Q: Draw the orthographic projections of given objec
A: Orthographic projection contain side front and top view
Q: Q2/ Draw by 2.5:1 scale the following shape. 4.00 2.50 001
A: Scale =Representative ValueTrue ValueSoAssuming that the 2.5 unit in Diagram will be Drawn as 1…
Q: FIND THE LENGTH OF THE DIVIDING LINE DP. THANK YOU. (THIS SUBJECT IS SURVEYING)
A:
Q: What type of drawing is shown (the bottom center of the object closest to the viewer comes to a…
A: A) 3 View incorrect. -> 3 view or orthogonal views are the projections when seen from a fixed…
Q: Q1:A)Write the command to draw Figure below by using Auto CAD program (Relative Coordinate Method).…
A: question being asked here is to draw the above diagram using AUTO CAD program and also clearly…
Q: Draw a grid 6 in wide by 7 in long with 1-in intersections, and place the given elevations at the…
A:
Q: Name any four shape that you can identify from the sketch
A: Any sketch such as still life, landscape etc. is prepared with the helps of basics shapes. These…
Q: Name: - Section:- X 100 * 200 + 250 + 300 350 *400 x450 x350 +250 300 x 500 200 x400 150 500 Draw…
A: Contour interval = 50 m So, the difference between these levels should be 50m We will draw contours…
Q: Why are sketches in field books not usually drawn to scale?
A: Sketch is the raw drawing depicting the main characteristics of an object. It refers to the drawing,…
Q: Given the isometric view of the cut block objects shown, use rectangular grid paper to sketch a…
A:
Q: Create a hand drawing of the isometric view of this object to scale.
A: First Draw one missing view from the given two view by projecting lines. A. After getting the…
Q: Show the orthographic views (top, front, right side) in CAD with dimensions.
A:
Q: The following geometric construction techniques are needed or useful in drawing lines externally…
A: Option C is correct.
Q: Civil Engineering Using the drawing board, draw the following views in 3rd angle projection: a) An…
A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…
Q: 50 10 Derive the third projection, taking into account the use of the rules for writing dimensions…
A: GIVEN: TO DETERMINE: TOP VIEW
Q: Using multiview, the user can layout drawings in different paper sizes at the same time. O True…
A: A multi-view drawing is one that shows two or more two-dimensional views of a three-dimensional…
Q: If you obtained a drawing that contained Auto CAD polylines representing contours, what is the best…
A: Contour lines : A contour line for a two-variable function is a curve that connects locations of…
Q: Draw or interpret the characteristics of Contours.
A:
Q: Use Scale ( 1:1 ), for the front and side views shown draw the isometric projection 22 19 38 Ф 18 22…
A: Given Data :
Q: Compute an actual dimension of a distance if the given drawing measurement in the plan is 28 cm…
A: Map scale A distance on a map and its corresponding distance on the planet are related by a scale.…
Q: (Figure 14.38) a. Draw a true-size view of planes AOC and DLN. b. Find the area of the largest…
A: The inclined angle is measured by proper techniques and formula and accurate calculation. The true…
Q: What are the types of coordinate system? Illustrate with neat figure.
A: Generally two types of coordinate systems viz, Catesian Coordinate. Polar Coordinate. Cartesian…
Q: Define: First Moment of Area Sketch Or Drawing: Equation: Units:
A:
Q: Define the terms Streamlines, Streaklines, Stream tube?
A: Streamlines Streamlines are a family of curves that are outright tangent to the velocity vector of…
Q: Sketch a 45-DEGREE CABINET OBLIQUE DRAWING from the attached orthographic projection. Follow the…
A: In cabinet oblique drawing, the axix in the plane of paper is drawn to the true scale, while the…
Q: Draw the minimum number of views necessary to represent the figure (for example top, front and / or…
A: To represent a 3D diagram in 2D we need three views Top view Front view Right or left side view…
Q: Draw a 45-DEGREE CAVALIER OBLIQUE DRAWING from the attached orthographic projection. Follow the…
A: In cavalier drawing, each axis is drawn to the true scale. 45 degree oblique drawing, the angle…
Q: Sketch an ISOMETRIC DRAWING from the attached orthographic projection. Follow the assigned…
A:
Q: Explain with the help of labeled sketch if applicable the different types of scale
A:
Q: the distance between two small lines marked in the scale ?
A: The fixed intervals with marks on it used for measuring mode is known as scale.
Q: What is the fastest method to create lines? O Relative Cartesian coordinate O Absolute Cartesian…
A: One can draw lines by Direct Distance Entry method in following way: Type Line or L in the…
Q: Draw the following AutoCAD drawings
A: Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at a…
Q: 30 85 20 35 15 10 15 009
A: Answer:- 1. Top view so section:
Q: Q 01: a) Why we need to draw sectional views of three dimensional drawings? b) Draw Section A-A of…
A:
Q: Using the drawing board, draw the following views in 3rd angle projection: a) An elevation as given…
A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…
Q: 3. Consider the drawing below. a. Find I, b. Find Ix 15 10
A: y = 3*x0.5 y= 3/5*x
Q: What is the minimum allowable number of layers in a drawing? 4 2 1
A: Ans = 1 All objects should be drawn on Layer 0 and then assigned to another layer. Always keep Layer…
Q: Derive the Trapezoidal rule for multiple segments. Also show a graphical sketch.
A:
Q: a) Draw the plan and elevation of the below given line plan. ASsume all data. Toilet 3X2 Bed room…
A:
Q: Drawing a house plan using Auto0CAD Drawing using the Offset tool
A: Offset is a very good function in Autocad that helps to draw the lines of the wall or any parallel…
Q: Write the command to draw Figure below by using Auto CAD program (Relative Polar Coordinate Method -…
A: First we will draw the base line or construction line:- Note: for enter command, we can press space…
Q: Show the orthographic views (top, front, side view) with dimensions.
A: D1 = 15mm D1' = 30mm D2 = 12mm D2' = 24mm
Step by step
Solved in 3 steps with 1 images
- Determine elevation at C. Please see picture.Please draw profile and longitudinal cross-sectionCreate contour lines on the grid provided using linear interpolation of points. Set the contour interval to 2m. Use the specified diagonal line for the linear interpolation.. (square) Solution for 1 side and 1 diagonal line only. Indicate the scale of your drawing. No true length for grid, and their location is more or less the same a) Draw index contour with thicker line than intermediate contour. b) Label the elevation of index contour.
- Find centroid (x,y) of a triangle inscired semicircle3)The accompanying tabulation gives elevations of points over the area 20m by 20m city lot.The elevations were obtained by the checkerboard method using 10-m squares. Requirements: a)Plot the contours using a horizontal scale of 6cm=10m and a contour interval of 1 meter. b)Use short-sized bond paper.All corner desiqnations and corresponding elevations must be indicated,including all vertical and horizontal lines. c)lndicate the following Index contours:880,885,890 & 895.The thickness of the index contours must be drawn about twice the thickness of intermediate contours. d)Show solutions in interpolations. 2 A 882.80m 888.60m 891.80m B 882.50m 890.40m 892.60m C883.20m 888.50m 892.80m GOD BLESS!A line CD starting at any point, C, is 8 m long bears N 35° W, and slopes downward from C to D at 40°. Draw the point view of CD. The scale is 1:200