1. The ideal Rankine cycle is shown below in schematic form and on a T-s diagram. The turbine power output of this cycle is 2 MW. Saturated liquid at 20 kPa leaves the condenser, and the vapor at the turbine exhaust has a quality of 95 percent. The boiler pressure is 1.4 MPa. Determine the mass flow rate of steam, the heat-transfer rate in the boiler, and the thermal efficiency of the cycle. 3

1. The ideal Rankine cycle is shown below in schematic form and on a T-s diagram. The turbine power output of this cycle is 2 MW. Saturated liquid at 20 kPa leaves the condenser, and the vapor at the turbine exhaust has a quality of 95 percent. The boiler pressure is 1.4 MPa. Determine the mass flow rate of steam, the heat-transfer rate in the boiler, and the thermal efficiency of the cycle. 3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 1 Consider a simple, ideal Rankine cycle operating with a 15 kPa condenser and a turbine inlet temperature of 500°C. Determine the following: a. Turbine exit quality, specific net work produced, and the cycle's thermal efficiency when the boiler operates at a pressure of 2 MPa.
An ideal Rankine cycle operates between a steam boiler pressure of 18 MPa and a condenser temperature of 42 °C. The steam leaving the boiler is a saturated vapor. The net power generated by the cycle is 150 MW. What is the mass flow rate of steam? What is the cycle efficiency? Use the formula: n=Wnet/Qin.
A steam power plant operates on the simple ideal Rankine cycle. The steam enters the turbine at 4 MPa and 500°C and is condensed in the condenser at a temperature of 40°C. draw and label the schematic diagram and the pV and TS planes. (a) Show the cycle on a T-s diagram. If the mass flow rate is 10 kg/s, determine (b) the thermal efficiency of the cycle (c) the net power output in kW.
Superheated steam at 11,200 kPa and 615°C, enters the 1st stage turbine and expands to 150 kPa. It is then reheated to 340°C before entering the 2nd-stage turbine where it expands to a condenser pressure of 10 kPa. The net power output is 100, 000 kW. The turbine and pump efficiencies are 82%. Determine for the cycle: (a) the network per unit mass of steam flow in kJ/kg (b) the heat transfer rate to steam passing through the boiler and the heat transfer rate to cooling water passing through the condenser in kJ/s (c) the thermal efficiency.
A steam Rankine cycle operates between the pressure limits of 1500 psia in the boiler and 2 psia in the condenser. The turbine inlet temperature is 800F. The turbine isentropic efficiency is 90 percent, the pump losses are negligible, and the cycle is sized to produce 2500 kW of power. Calculate the mass flow rate through the boiler, the power produced by the turbine, the rate of heat supply in the boiler, and the thermal efficiency.
Consider a steam power plant operating on the simple ideal Rankine cycle. The steam enters the turbine at 4 MPa, 400 degrees celcius and is condensed in the condenser at a pressure of 100 kPa. Draw the schematic and T-s diagram of the cycle and determine the following per unit mass of steam. (a) Turbine work (b) Pump work (c) Heat added in the boiler (d) Heat rejected in the condenser (e) Thermal efficiency of the cycle (f) Heat rate (g) Steam rate of the cycle
Required information. The net work output and the thermal efficiency for the Carnot and the simple ideal Rankine cycles with steam as the working fluid are to be calculated and compared. Steam enters the turbine in both cases at 10 MPa as a saturated vapor, and the condenser pressure is 50 kPa. In the Rankine cycle, the condenser exit state is saturated liquid and, in the Carnot cycle, the boiler inlet state is saturated liquid. Draw the T-s diagrams for both cycles. (Please upload your response/solution using the controls below.) upload a response file (15MB max) Choose File no file selected save
A 330 MW steam power plant operates according to the simple ideal Rankine cycle. Water vaporenters the turbine at 10 MPa pressure and 525 ° C temperature and 15 kPa condenser pressureIt is expanding. A T-s with cycle, saturated liquid and saturated steam curvesshow in the diagram and (a) the degree of dryness of the steam at the turbine outlet, (b) the thermal efficiency of the cycle,(c) calculate the mass flow of water vapor circulating in the cycle
An ideal RANKINE cycle delivers 210 MW of power. Steam enters the turbine at 10 MPa and500C and is cooled in a condenser at 10 kPaa. Determine the thermal efficiency of this cycleb. Mass flow of waterc. Heat rejected in the condenserd. Work inputted to the pump (remember the volume is constant)
In the ideal Rankine cycle shown, the boiler pressure is 6 MPa and the condenser pressure is 8 kPa. The steam enters the turbine at 440°C at a mass flow rate of 7.0 kg/s. In your written solution, (a) determine the enthalpies at states 1, 2, 3, and 4; (b) draw the T-s diagram with the states in the correct region; (c) determine the cycle power output; and (d) the cycle thermal efficiency.
In an ideal Rankine cycle, steam is generated at 4.1 MPa and 486.5°C. The condenser is at 32°C. Determine: (Sketch the T-S Diagram and Schematic Diagram of the cycle) (28 ) a. The ideal pump work b. The cycle thermal efficiency
QUESTION 1 Boiler HP LP 6 Turbines Condenser Pump In a reheat ideal Rankine cycle, steam enters the high-pressure turbine at 9.0 MPa and 650°C. The steam expands until it becomes saturated vapor and then reheated to 550°C. It re-enters a low-pressure turbine and expands to a condenser pressure of 10 kPa. Determine the following: (a) Temperature, Pressure, and Enthalpy of the stream leaving the high-pressure turbine to be reheated (Stream 4) (b) Work generated by the two (2) turbines: (b) Work done on the pump: and (c) cycle efficiency. Note that the stream leaving the low-pressure turbine can either be a wet steam or a superheated steam. As part of your solution, fill up the table below. Stream P (in bar) (in kJ/kg) S (in kJ/kg-K) (you do not need to completely fill this table, only those needed in the calculations) WT