Answered: 1. Shearing stress differs from tensile…

Name: 31. Shearing stress differs from tensile and compressive stress since
Uploaded: 2024-03-20T06:56:46.000Z
Channel: Bartleby
Description: 31. Shearing stress differs from tensile and compressive stress since it is caused by forces acting___________to the area resisting the force.A. PerpendicularB. 5 degreesC. ParallelD. 30 degrees

Science

Physics

1. Shearing stress differs from tensile and compressive stress since it is caused by forces acting ___________to the area resisting the force. A. Perpendicular B. 5 degrees C. Parallel D. 30 degre

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter12: Fluid Dynamics And Its Biological And Medical Applications

Section: Chapter Questions

Problem 22CQ: Explain why the viscosity of a liquid decreases with temperature—that is, how might increased...

See similar textbooks

Similar questions

Explain why the viscosity of a liquid decreases with temperature—that is, how might increased temperature reduce the effects of cohesive forces in a liquid? Also explain why the viscosity of a gas increases with temperature—that is, how does increased gas temperature create more collisions between atoms and molecules?
Calculate the percentage elongation from the length of the steel bar is 25 cm, and the extension is 3 mm. O a. 0.012 O b. 0.12 O c. 2.1 O d. 1.2
1. Considering only shearing stress in the lap joint, does the load capacity change when the plate's thickness or width is increased? Why? W Plan Elevation II. In the above examples, the lap joint uses the same diameters of rivets. How about if the plates are joint with different diameters of rivets? Does the formula (t = P/A) can still be used? Explain.
Choose correct dimensional equation to stress. [Hint: Stress = ForceIArea] O a. M°L'T? 0.1 -2 а. O b. M'L"T? -1 -2 L'T 1-1 -1 O c. M'L T 10 -2 O d. M'L T
The rectangular piece of wood, 82 mm by 162 mm, is used as a compression block. The grain of the wood makes a 33.5° angle with the horizontal, as shown in the figure. Determine the largest axial force P (in N) that can be applied safely if the allowable stresses on the plane of the grain is 11.1 MPa for compression. Round off the final answer to three decimal places. 018 shear.png
1. At a certain ocean depth, the pressure is 1.71x108 Pa. Calculate the change in volume of 1.00 m3 of seawater carried from the surface to this deepest point. The compressibility k of water is 45.8x10-11 Pa-1.
4. A steel shaft 4 ft long that has a diameter of 5 in is subjected to a torque of 20 kip-ft. Use a standard G = 12 x 106 psi. a. Set up the equations of stress and twisting angle that is required to solve the problem. b. Determine the maximum shearing stress and the angle of twist
A tensile load of 45 kN is applied to 15 mm diameter bar. Calculate the engineering stress on the bar. Circle the most appropriate answer based on your calculation. Select one: a. 255 MPa b. no appropriate answer C. 255 GPa d. 0.255 MPa
7. A vertebra experiences a shearing force, F; = 600N. What is the magnitude of the shear deformation if the vertebra is treated as a cylinder 3 cm in height and 2 cm in radius? S = 10’ N/m?.
Q)The state of plane stress at a point is represented by the stress element below: A. Draw the Mohr's Circle. B. Determine the principle stresses and draw the corresponding stress elements. C. Determine the maximum shear stress and draw the corresponding stress element. D. Find the stresses on an element inclined at 30° clockwise and draw the corresponding stress element. E. Provide a table illustrating the stress values as well as the inclination angles and compare the obtained values from Mohr's Circle with those obtained from equations 60 MPa 50 MPa 30 MPa
A load of 300 N acts on a bar having a cross- sectional area of 0.6 mm2. The stress developed in the bar is C Select one: a. 500 Pa b. 450 Pa c. 500 MPa O d. 450 MPa
3. A copper wire LM is fused at one end, M to an iron wire MN as shown in figure below. M N F The copper wire has length 0.90 m and cross-section area 0.90 x10-6 m². The iron wire has length 1.40 m and cross-section area 1.30 x10-6 m². The compound wire is stretched and the total length increases by 0.01 m. Given Yıron = 2.10 ×1011 Pa and Give Ycopper = 1.30 ×1011 Pa. Determine a. the ratio of the extension of copper wire to the extension of iron wire, b. the extension of each wire, and c. the applied force to the compound wire. [1.5, 4.0 mm, 6.0 mm, 780 N]