1. Represent the decimal values 11 and -10 as 8-bit signed integers. Add the two binary representations. What is the binary result? What decimal value does that 2's complement result represent? 2. Perform the following arithmetic operation involving 8-bit binary integers. Give the result and CF and OF flag values for ARM microprocessors. Explain 01011011B + 01011011B 10011011B 01011001B

1. Represent the decimal values 11 and -10 as 8-bit signed integers. Add the two binary representations. What is the binary result? What decimal value does that 2's complement result represent? 2. Perform the following arithmetic operation involving 8-bit binary integers. Give the result and CF and OF flag values for ARM microprocessors. Explain 01011011B + 01011011B 10011011B 01011001B

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

An eight bit number, 01011101, is: 1)added to 4 2) subtracted from -10 3) ANDED with 15 a) What is the outcome of these operations in binary? b) What is this number in decimal? c) What is the original number in decimal?
Explain the arithmetic operations in binary number system and how code conversion is done between binary and decimal numbers.
Q3) A - Convert the Excess-3 to binary number : ( 110001011100.10001010)ex-3 B- convert each Gray code to binary: 1-( 011010001001)G 2-(59)D
Add two binary floating-point numbers (1.101101x23)2 and (1.010101x22)2. What is the decimal floating-point number of the result?
1. Write the contents of all registers and the conditions codes registers after each execution instructions in Table Q1(a). Instructions SUBS r0, rl, 12 MOV 12,13, ASR #3 ro 11223344 Table Q1 (a) rl F7770025 12 r3 CF119856 CF119856 NZ V C 010 1
8085 microprocessor went through its manipulation operation in the ALU, the results was transferred on the data bus and status of the results was stored in the flag register for indications . With your knowledge and understanding illustrate a complete bit configuration of 8085 flag register and show the functions of the represented bits in the register.
How to build this circuit? (on Digital or Logisim) Binary-coded decimal is an alternative method of representing integers using binary. In it, each base-10 digit is represented by four bits, thus each nibble takes one of 10 values (0000 through 1001). Therefore, using BCD, 42 (decimal) is represented as 0100 0010 (binary) and 196 (decimal) is represented as 0001 1001 0110 (binary). Create a circuit in Logisim that accepts as input a pair of two-digit integers represented as BCD and outputs their sum in BCD. Any and all Digital components are fair game. You can assume that all inputs will be valid BCD-encoded numbers.
1. An 8-bit register contains the number 10000110. The serial number 11011011is applied to the input. After 5 shift pulses, what is the number in the shift register? Assume shift right operation 2. A binary number is shifted 5 positions to the left. The number therefore has been 3. A binary number must be divided by 128. How many positions must the number be shifted (and in what direction to achieve this?
Design a sequential circuit (overlapping) with an input ‘x’. The pattern to be detected is the binary number that is equal to 01100 For this circuit:Draw the logic circuit for the datapath.
1. Convert the following 32-bit IEEE single precision floating point number to base-10 representation. (01000011000011001000000000000000)2 = ?
Question 3 a) Convert the following unsigned binary numbers to decimal. i) 101101112 ii) 010011012 iii) 100101102 b) Assume a digital to analog conversion system uses a 10-bit integer to represent an analog temperature over a range of -100C to 1000C. If the actual temperature being read was 36.5oC, what would be the closest possible value that the system could represent? Expiain the term aliasing and discuss how it can be avoided in digital sampling. d) Show the output waveform of an AND gate with the inputs A, B, and C indicated in the figure below. A B C
2. Convert the following binary numbers to the decimal. (10110011)2: (100011101)2; and (111000) (130)