1. (Prob # 11.13, pg. 437) A balanced A-connected load has an impedance of 60+j45/. The load is fed through a line having an impedance of 0.8+j0.60/6. The phase voltage at the terminals of the load is 480V. The phase sequence is positive. Use VAB as the reference. a) Calculate the three phase currents of the load b) Calculate the three line currents. c) Calculate the three line voltages at the sending end of the line.

1. (Prob # 11.13, pg. 437) A balanced A-connected load has an impedance of 60+j45/. The load is fed through a line having an impedance of 0.8+j0.60/6. The phase voltage at the terminals of the load is 480V. The phase sequence is positive. Use VAB as the reference. a) Calculate the three phase currents of the load b) Calculate the three line currents. c) Calculate the three line voltages at the sending end of the line.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.42P: A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase...

See similar textbooks

Similar questions

A balanced positive-sequence wye-connected 60-Hz three-phase source has line-to-line voltages of VL = 440 V rms. This source is connected to a balanced wye-connected load. Each phase of the load consists of a 0.5-H inductance in series with a 30-Ω resistance. Assume that the phase of VanVan is zero. FIND Ia,Ib,Ic, Find the power delivered to the load And Find the reactive power delivered to the load.
Three impedances (4-j6) ohm, (6+j8) ohm, and (5-j3) ohms are connected in parallel. Calculate the current in each branch when the total supply current is 20 A. Please provide its solution...its urgently needed...please.
Example: A balanced positive-sequence wye-connected 60 Hz three-phase source has line-to- line voltages of V,=1000 V. This source is connected to a balanced wye-connected load. Each phase of the load consists of a 0.2 H inductance in series with a 100 0 resistance. Find the line-to-neutral voltages, the line currents, the power, and the reactive power delivered to the load. Assume that the phase of Van is zero.
A three-phase system has balanced conditions so that the per-phase circuit representation can be used as shown in Figure 1 Select the turns ratio of the step-up and step-down transformers that the system operates with an efficiency greater than 99 percent. Moreover, find the complex power (received or given) of all components in the circuit and the V1 and V2 voltages. The load voltage is specified as 4 kV rms, and the load impedance is 4/3 ohm. ..
2. A single-phase a.c. distributor AB is fed from end A and has a total impedance of (0-2 + j 03) ohm. At the far end, the voltage V = 240 V and the current is 100 A at a p.f. of 0-8 lagging. At the mid-point M, a current of 100 A is tapped at a p.f. of 0-6 lagging with reference to the voltage Vy at the mid-point. Calculate the supply voltage V, and phase angle between V, and Vg- [292 V, 2-6°] a loade
A delta connected load of impedances (6 + j9) ohms each is supplied through a line having an impedance of (1 + j2) ohms. The supply voltage is balanced 3-phase, 400 V, 60 Hz mains. Find the total power drawn by the load.
A 230 V, 50 Hz power source is connected to the some loads, where: • Load-1: R = 4.5 Q and in series connection with L = 8 mH. • Load-2: 10 kVA of power factor 0.6 lagging. • Load-3: 5 KVAR of power factor 0.5 lagging. (i) Determine the active power and reactive power of the Load-1. (ii) Determine the total current delivers by the supply and the total power factor. (iii) Calculate the required capacitor in order to increase the power factor to unity.
A balanced delta connected load has an impedance of (60 +j45) ohm per phase. The load is fed through a line having an impedance of (0.8 +j0.6) ohm per phase. The phase voltage at the terminals of the load is U =480V. The phase sequence is positive.N.B: Use UAB as the reference.a- Calculate the three phase currents of the load.b-Deduce the three line currents I.c- Construct the a-phase equivalent circuit of the system.d- Calculate the three line-to-neutral voltages at the sending end of the line e-deduce the threee to line voltages
Two balanced three phase loads are connected in parallel, the loads are L1= 20 kW at 0.7 pf lead, and L2= 12 kVA at 0.9 pf lag. The loads are fed from a distribution line with an impedance of 0.05+j0.2 Q/P. The line to neutral voltage at the load end is 203 V and zero phase shift, the capacitance of A-connected capacitor bank that connected parallel to the loads to improve the power factor to unity in uF is; (f=60 Hz) O A. None B. 325.49 O C. 976.48 O D. 108.50 O E. 36.17
A balanced delta-connected load is supplied by a 50-Hz three-phase source with a line voltageof 240 V. Each load phase draws 6 kW at a lagging power factor of 0.8. Find:a) the load impedance per phaseb) the line currentc) the value of capacitance needed to be connected in parallel with each load phase tominimize the current from the source
Under balanced operating conditions, consider the 3-phase complex power delivered by the 3-phase source to the 3-phase load. Match the following expressions, those on the left to those on the right. 0) Real power, Py (ii) Reactive power, Qu (ii) Total apparent power Sy (iv) Complex power, Sy (a) (V3 VLL. IL)VA (b) (V3 Vu sng) var (e) (V3 VLL. IL cos ø) W (d) Py +Qy Note that VLL is the rms line-to-line voltage, IL is the ms line current, and o is the power-factor angle.
Two delta connected loads are connected in parallel and powered by a balanced Y-connectedsource. The smaller of two loads draws 10 kVA at a lagging power factor of 0.75 and the largerdraws 25 kVA at a leading power factor of 0.8. The line voltage is 400 V. Calculate a) The powerfactor at which the source is operating. b) The total power drawn by the two loads. c) The phasecurrent of each load.