5whilereducбылеtimeLOTIUDIXExercises:For the steel U-shape design (diameter: 3/4"), determine the maximum stressdeveloped under a loading of P-200 lb.JThree-Dimensional Solid Elements0.5-#P-3.5-R0.75-R0.75-| 5.0-.60-shown below and compare the results.2. For the above problem, perform additional FEA analyses using the two cross-sections11-33.55

Given: The diameter of the U shape: →d=34 inch=0.75 inch So the cross sectional area of the U shape:…

Answered: 1. For the steel U-shape design…

1. For the steel U-shape design (diameter: 34"), determine the maximum stress developed under a loading of P=200 lb. ៗ 0.5- P -3.5- R0,75— R0.75- the 5.0 two cross-sections

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.1P: The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the...

See similar textbooks

Related questions

Q: A coal-fired power plant produces a net power of 300 MW with a total thermal efficiency of 32…

Q: The roller coaster car has a speed of VA = 36 ft/s when it is at the crest of a vertical parabolic…

Q: A cylinder of internal diameter 2.5 m and of thickness 5cm contains a gas. If the tensile stress in…

Q: The 5 lb box is projected with a speed of 20 ft/s at point "A" up the smooth vertical circular…

Q: As depicted, a column is contained by a rigid material on its x-axis and has initial dimensions of…

Q: can u explain to me why this solution isnt correct?

Q: The figure shows a 5.50 kg block on a ramp. The block is also attached to a massless spring with…

Q: The normal and shear stresses in MPa at point P are respectively a) 67.9 and 56.6 (b) 56.6 and 67.9

A: Given data:Force applied, F=600 NDiameter, d=30 mm

Q: Please help me find out where you got the s values from for the exergies for each of the processes,…

Q: A column has a rectangular cross-section of 10mm x 20mm and a length of 1m. The slenderness ratio of…

A: Given data:Cross-section of column is 10 mm×20 mm,Length of the column is 1 m,

Q: Problem 3 A uniform block of steel (s=7.85) will float at a mercury-water interface as shown in the…

Q: Vhat is the accuracy for the given scale in meter (m)? 0 0.5 1.0 1.5 2.0 cm

A: Given,

Q: Required information Problem 08.034 - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS - Refrigerant…

Q: 11 Calculate the work done in blowing a soap bubble of diameter 100 mm. Assume the surface tension…

A: surface tension S=0.038 N/m Diameter D=100mm=0.1m have to calculate work done

Q: The 16-kg block is held at rest on the smooth inclined plane by the stop block at A. (Figure 1)…

A: Given data: M=16 kgm=10 gram=0.01 kgvb=240 m/s Need to determine the distance the block will slide…

Q: In a basketball game, the point guard A intends to throw a pass to the shooting guard B, who is…

A: Given: Velocity of shooting guard, vs=14 ftsec Shooting guard from B to C, sc=25 ft Final height in…

Q: Car A is traveling at a location where the speed limit is 100 km/h. The police officer in car P…

Q: 14 Derive an expression for the capillary rise at a liquid having surface tension o and contact…

A: According to the company's guidelines when multiple questions are asked only first question has to…

Q: 3 decimal places Convert specific heat 0.53 BTU/lb-F to kJ/kg-K

Q: Given: The plate( The shaded rectangular volume) has weighs 240 lbf. It is. suspended by able CD,…

A: Given: To find: Tension in cable CD

Q: The velocity of an object is given by: v (t) = 4t - 3t² Where v is in m/s and t is in seconds. If…

Q: Q1: Which one is stronger; pure copper with 10-μm grains or pure copper with 100-um grains? Q2:…

Q: A projectile is launched from point A with speed vo = 20 m/s. Determine the value of the launch…

Q: THERMODYNAMICS (UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS. NO LONG EXPLANATION…

Q: We wish to produce a 0.3 inch thick plate of 3105 aluminum having a tensile strength of at least…

A: Given Data: Required Tensile Strength TS ≥ 25000 psi Required % Elongation ≥ 5% Original thickness…

Q: 6-73. The wind turbine has an efficiency of 48% in an 8 m/s wind. If the air is at a standard…

A: Givenη=48%V=8m/sair at standard atmospheric pressure and a temperature 20oCd=35m

Q: A rigid tank is divided into two equal parts by a partition. One part of the tank contains 2.5 kg of…

A: Given Mass of compressed liquid = 2.5 kg Intial pressure p1 = 400 kPa Intial temperature T1 = 60°…

Q: 9. The floating fastener formula is: where T = H = and F =

A: As per our guidelines we can answer only first question. Kindly post the remaining questions in…

Q: A placekicker is attempting to make a 59-yard field goal. If the launch angle of the football is…

Q: A block of wood 0.20 m thick is floating in sea water. the specific gravity of wood is 0.65 while…

A: Given Thickness, t = 0.2 m Specific gravity of wood, SGw =…

Q: During a non-flow thermodynamic process(1-2) executed by a perfect gas, the heat interaction is…

A: Given that: For a flow process, Q1-2 = W1-2 It is required to determine the process.

Q: 5. Consider a 55-kg woman who has a total foot imprint area of 400 cm². She wishes to walk on the…

Q: u rewrite

A: Given data s per question Mass of car, m=1700 kg Angle of banking,θ =350 Radius of curvature,ρ=100 m…

Q: A double-parallelogram mechanism is shown in the figure. Note th single link. The mobility of the…

A: Given data: Double parallelogram linkage,

Q: 5. The frame shown below is supported by a pin at A and a roller at E. Determine the reactions at…

Q: Compute the elongation, in %, of a cylindrical copper rod if it is cold worked such that the…

A: Givendi=15.9mmdf=10.4mm

Q: A projectile is launched from point A with the initial conditions shown in the figure. Determine the…

A: Given: VO = 129 m/s θ=35o

Q: The forces F1 and F2 in the figure are parallel to the x-axis, while the force F3 is perpendicular…

Q: The A-36 steel assembly consists of a tube having an outer radius of 1 inch and a wall thickness of…

A: Given data: T=200 lb.inro=1 int=0.125 indAB=1 in Need to determine the rotation of the tube’s end C.

Q: ! Required information Problem 07.021 - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS NOTE: This…

Q: Da entrance x=0 Mentrance FIGURE P4-21 u(x) lexit x=L Dexit 4-22 For the velocity field of Prob.…

A: For L = 1.56 m. uentrance= 22.6 m/s, uexit=17.5 m/s, calculate the acceleration at x=0 and x = 1.0…

Q: What is the power (?) lost to main crankshaft friction in a four-cylinder engine with a 100mmbore…

Q: A young man, 22 years old, graduated from college and got his first job. He wants to have a…

Q: Calculate the resulting moment of both forces with respect to point A Write the units of the result…

A: Moment: The product of the force with perpendicular distance between the line of axis of the force…

Q: Steam enters a turbine at 10 MPa and 600°C and exits at 0.1 bar. If the isentropic turbine…

A: Given turbine inlet temperature T1 = 6000 c = 600+273 K =873 K Pressure at inlet P1 = 10 MPa…

Q: Car A is traveling at a location where the speed limit is 100 km/h. The police officer in car P…

Q: W m-K A 5cm copper plate has a thermal conductivity of 395 is used as a heat sink for a…

A: Given:Thickness of copper plate, L1=5 cm=0.05 mThermal conductivity of copper plate, k1=395…

Q: The 80mm diameter shaft is made of 6061-T6 aluminum allow and subjected to the torsional loading…

Q: List any 3 project ideas of process improvement or design for industrial engineering

A: There are various process improvement processes which can be applied to enhance the quality and…

Q: A large block of steel is placed inside of a furnace set at 1980°C. If it is assum that the surface…

A: Given Density = 7832 kg/m3 Temperature, T1 = 1980oC T2 = 1000oC…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

5
while
reduc
быле
time
LOTI
UDIX
Exercises:
For the steel U-shape design (diameter: 3/4"), determine the maximum stress
developed under a loading of P-200 lb.
J
Three-Dimensional Solid Elements
0.5-
#
P
-3.5-
R0.75-
R0.75-
| 5.0
-.60-
shown below and compare the results.
2. For the above problem, perform additional FEA analyses using the two cross-sections
11-33
.55

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
At a point on the web of a girder on an overhead bridge crane in a manufacturing facility, the stresses arc known to be x = —4300 psi, a = 1700 psi, and r = 3100 psi (the sign convention for these stresses is shown in Fig, 7-1). A stress clement located at the same point in the structure (but oriented at a counterclockwise angle 0, with respect to the _y axis) is subjected to the stresses shown in the figure {b, r», and 2100 psi). Assuming that the angle 8Xis between zero and 90°, calculate the normal stress trA, the shear stress ta, and the angle Bv
Solve the preceding problem for the following data: diameter LO m, thickness 48 mm, pressure 22 MPa, modulus 210 GPa. and Poisson's ratio 0.29
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
A fire extinguisher tank is designed for an internal pressure of 825 psi. The tank has an outer diameter of 4.5 in. and thickness of O.OS in. Calculate the longitudinal stress, the circumferential stress, and the maximum shear stresses (out-of-plane and in-plane) at the outer surface of the tank.
A simply supported beam is subjected to point load P at mid-span. The normal stress on an element at mid-span is known to be ??x= 1.5 ksi. Determine the element stresses lilt is rotated through angle ? = 450• Show these stresses on a sketch of an element oriented at that angle.
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial stress and is subjected to stresses a = -48 MPa and ay = 19 MPa, as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an clement oriented at a counterclockwise angle ?? = 25° from the x axis. (b) The maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.