1. For the following mechanical translational system a. Write two differential equations of Order in s domain b. Change to time domain, and choose state variables c. Write the state equations, and the state matrix equation d. Write the output equation if x2 is the output Hint: the state variables will be x1, V1, X2, V2 *(1) fv, (1) At) K K3 K2 M2 000

1. For the following mechanical translational system a. Write two differential equations of Order in s domain b. Change to time domain, and choose state variables c. Write the state equations, and the state matrix equation d. Write the output equation if x2 is the output Hint: the state variables will be x1, V1, X2, V2 *(1) fv, (1) At) K K3 K2 M2 000

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Determine which of the graph have Euler circuit, Euler trail, Hamiltonian circuit.For each graph, if the graph does not have any of them, whether one or two of themexplain why not. If it does have any of them, describe one for each of them.
Design the state diagram and create the state table for a synchronous modulo-3 counter (that is, one that continually counts in the sequence 0, 1, 2, 0, 1, 2, . . .). Write the equations for the state variables. Note: In this case, the state variables can be used as the outputs.
Draw the state diagram for a Modulo-6 synchronous counter which follows the count sequence000, 010, 011, 001, 100, 110, 000, 010, … . Show all possible states including the ones that are notdesired. The undesired states should be depicted to be transiting to any of the desired states.Choose the 000 state for this purpose. It is important to include the undesired states to ensure that,if the counter accidentally gets into any of these undesired states owing to noise or power-up, thecounter will go to a desired state to resume the correct sequence on application of the next clockpulse.
Q1/B/ Determine the analog voltage output for the Figure shown below if the waveforms representing a sequence of 4-bit numbers in the Figure below are applied to the inputs. Input Do is the least significant bit (LSB), where Input Digital Signal are (Do = 0001), (D1 = 0010), (D2 = 0100) and (D3 1000). While Digital Voltage is 5v. %3D %3D 80 kn De o R 40 kn 20 kn 20 kn Dz O 10 kn Vout(Da) Vout(D) = - Vout(o) -. Voutcb)
a) Briefly explain Continuous signals, Discrete Time signal and Digital Signals. Include diagrams/waveforms and examples of each type of signals. b) Compare the Continuous and digital signals by mentioning at least two advantages and disadvantages of both types of signals
Minimize this equation
A thermal bimorph can be used as an actuator. In this problem, you will use the principles of “crayon engineering” to design a process and mask set that will produce a silicon‐based cantilever thermal bimorph with an integrated heater and an underlying hole structure as shown below. (Silicon‐based means that the final structure is made of silicon, plus oxide, nitride, and metal as needed. You don’t have to use a plain silicon wafer, but you can’t make the whole thing out of a completely different material like metal or SU8.) A description of the structure follows; a top view is shown in Figure 2. Where a dimension is not specified (like the lateral extent of the hole), you are free to choose a process that you think makes sense. This may turn out to be an economic trade‐off (for example, cost of processes vs. wasted space on the wafer). Cantilever composition: The cantilever includes a silicon structure, a metal layer on top of that (you can choose either Al or Au), an integrated…
Hello. I am confused which route to take for this problem. I could break it into parts, but do I put it into its odd and even functions for symmetry? Could you guide me through this problem? Thank you for your help.
PLEASE ANSWER USING MATLAB CODE AND INCLUDE A PICTURE OF THE SIMULATION RESULTS!! PLEASE NOTE C=4
Match the differential expression to its units. ✓rdp A V V R2 sin0d0dp R² sin0d0dqdR - ✓ de A. m² B. m3 C. m D. rad
Reduce the following block diagrams .. Please answer all subpart please..
Please solve Max in 30-45 minutes with full step and explanation thank u Explain what is meant and the function of virtualenv.