1. Define the Kinematic Analysis, 2. What are the fundamental structures? Give an example for each one. 3. Define the Strain and write its formula? and briefly explain the types of strain? 4. Draw one or several diagram(s) to illustrate the terms: fold wavelength, fold amplitude, hinge line, axial plane. 5. Draw one or two diagram(s) to illustrate the difference between buckling by flexural shear and orthogonal flexure. 6. How would you explain the differences between thrust fault and Reverse faults? Are their kinematics in any way similar to Normal faulting and Strike Slip? 245 Cuう

1. Define the Kinematic Analysis, 2. What are the fundamental structures? Give an example for each one. 3. Define the Strain and write its formula? and briefly explain the types of strain? 4. Draw one or several diagram(s) to illustrate the terms: fold wavelength, fold amplitude, hinge line, axial plane. 5. Draw one or two diagram(s) to illustrate the difference between buckling by flexural shear and orthogonal flexure. 6. How would you explain the differences between thrust fault and Reverse faults? Are their kinematics in any way similar to Normal faulting and Strike Slip? 245 Cuう

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4. The maximum stress a human tendon can withstand is estimated to be 1200 MPa. If you were to test it for rupture what load cell you should use (25ON or 5kN) what problems may occur if you select an incorrect load cell. 5. The figure below is a J-shaped (or concave upward) stress-strain curve. What does a J-shaped stress stain curve indicate about a material's response to stress and tendency to yield? Name two materials that have J-shaped stress strain curves.
Question-1: The strain rosette shown in the figure was used to obtain normal strain data at a point on the free surface of a machine part. (a) Determine the strain components &, S, and %, at the point. (b) Determine the principal strains and the maximum in-plane shear strain at the point. (c) Draw a sketch showing the angle 6, the principal strain deformations, and the maximum in-plane shear strain distortions. (d) Determine the magnitude of the absolute maximum shear strain. 45 45 &- 50 με, 8--730 με , ε375 με, ν-0.30
Define the term Absolute Maximum Shear Strain?
Example: Convert the change in length data in Table 3-2 to engineering stress and strain and plot a stress-strain curve Homework- help Table 3-2 The results of a tensile test of a 0.505 in. diameter aluminum alloy test bar, initial length (1o) = 2 in. Calculated LTO Load (Ib) Change in Length (in.) Stress (psi) Strain (in./in.) 0.000 1000 0.001 0.0005 4,993 14,978 24,963 34,948 37,445 39,442 39,941 39,691 37,944 3000 0.003 0.0015 5000 0.005 0.0025 7000 0.007 0.0035 7500 0.030 0.0150 7900 0.080 0.0400 8000 (maximum load) 0.120 0.0600 7950 0.160 0.0800 7600 (fracture) 0.205 0.1025
Sketch a representative stress-strain digrama for a ductile material showing the following on it (label the axis and provid units). 1- YIELD STRENGTH. 2- TENSILE STRENGTH. 3- FRACTURE POINT. 4- HARDENING PART. 5- SOFTENING PART. 6- A METHOD TO CALCULATE THE STIFFNESS. 7- A METHOD TO CALCULATE THE DUCTILITY.
No wrong answer please , i could downvote The piece of suture is tested for its stress relaxation properties after cutting 3 cm long sample with a diameter of 1mm. The initial force recorded after stretching 0.1 cm between grips was 5 Newtons. Assume the suture material behave as if it has one relaxation time. The gage length was 1 cm. a. Calculate the initial stress. b. Calculate the initial strain. c. Calculate the modulus of elasticity of the suture if the initial stretching can be considered as linear and elastic. d. Calculate the relaxation time if the force recorded after 10 hours is 4 Newtons.
You are given a square rod of 6061-T6 aluminum (cross-section = 4mm X 4mm, length = 2.3m). The material has a Young’s modulus of 72 GPa. If a compressive load of 3 kN is applied parallel to the 2.3m dimension, what is the resulting engineering normal strain?
The relationship between true strain (ɛ-) and engineering strain (ɛ) in a uniaxial tension test is given as (a) & = In (1 + &7) (c) &7= In (1+ E) (b) ɛg = In (1- E) (d)= in (1- E) %3D %3D
The Highest load sustained druing an uniaxial tensile testing experiment is 7,500lb. If the original cross section has a diamter of 0.25in, what is the ultimate tensile strength? (please also make a drawing)
Define the term Normal Strain?
! How to compute the strain displacement matrix for each element?
Strain of Silly Putty: Initial length (L0): 2.85 cm Final length (L): 8.50 cm Strain: % (show calculation below): (Please type answer no write by hend)