1. Consider the circuit below. Answer a-b. 80 N 40 Ω S0 V 5on | 750 mA § 200 A.) Suppose we kill the 50V source, leaving only the 750 mA source. What is the relationship between the 40 ohm and 50 ohm resistors? Select one: Oa. Series O b. Parallel O c. Neither series nor parallel B.) Suppose we kill the 750 mA source, leaving only the 50V source. What will be the resulting relationship between the 40 ohm and the 200 ohm resistors? Select one: O a. Series O b. Parallel O c. Neither series nor parallel

1. Consider the circuit below. Answer a-b. 80 N 40 Ω S0 V 5on | 750 mA § 200 A.) Suppose we kill the 50V source, leaving only the 750 mA source. What is the relationship between the 40 ohm and 50 ohm resistors? Select one: Oa. Series O b. Parallel O c. Neither series nor parallel B.) Suppose we kill the 750 mA source, leaving only the 50V source. What will be the resulting relationship between the 40 ohm and the 200 ohm resistors? Select one: O a. Series O b. Parallel O c. Neither series nor parallel

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Similar questions

A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l33.2AI4RT3.582R116R210R3R420PTP1P2P3P4
for the circuit shown below If v_in=5 sin2m10t then corner frequency will be ......Hz 1 UF 2 k Ohm 1 k Ohim 050 060 070 080 vin
Here are the values of the resistors, capacitance and the Is. Is= 7.8 A , r1= 7.1 ohms , r2= 3.8 ohms , r3= 5.5 ohms , C= 1 uF
The circuit in the figure is fed by a sinusoidal alternating voltage with a frequency of 50 Hz. The circuit consists of a resistor and a capacitor with the capacitance C= 600 μ Q. The power supplied to the circuit is P=400 W and the voltage across capacitor is UC=90 V. a) Calculate the current I. b) Calculate the resistance R. c) Calculate the voltage U (amount). d) Calculate the phase angle of the circuit
30 Ω resistor in the circuit in the figure.and 1.273 mH coil to the source with a frequency of 5 kHzconnected to the sinusoidal source. ResistanceSince VR=6 V voltage drops on itthe voltage falling on the inductance, the sourceCalculate the voltage, active and reactive powers.
(Basic Electrical Engineering) A series circuit consisting of a 13-ohm resistor, 0.05 H inductor and a 10-microfarad capacitor is connected across a 100V. Determine the frequency of the supply if the current flowing is 5A. Show complete solution and limit your answer jnto three decimal places.
An emergency power supply is required to provide a three-phase sinusoi- dal voltage source of 208 V (L-L) at a frequency of 400 Hz. The power is to be obtained from a battery consisting of cells in series, each cell hav- ing an internal voltage of 2.2 V and an internal resistance of 0.006 m. The load on the three-phase, 400-Hz system requires a fundamental fre- quency apparent power of 7.2 kVA at 0.9 power factor lagging. The in- ductance of the load is such that harmonic currents are negligible. How many cells should be connected in series to provide the required output? The switches may be regarded as ideal.
In a series circuit with the following devices to a 230volts 60Hz supply with a resistor in the range of 300 ohms and 990 ohms. What are the steps in calculating the impedance ...
A capacitance is a circuit component that opposes the change in circuit A. current B. voltage C. impedance D. none of the above
A series circuit consisting of a variable resistor in series with a capacitance of 80uF is connected across a 120V, 50hz supply. To what value should the resistor R be adjusted so that the power absorbed by the series circuit will be 10o0W?