V4 1. A feeder is made up of three conductors (500 MCM, copper, 75°C rated) that are placed in a conduitwhere the ambient temperature is 35°C. Determine the ampacity of each conductor.2. Six #10 THW copper conductors (rated for 75°C) are placed in a single conduit where the ambienttemperature is 30°C. Determine the ampacity of each conductor.

“Since you have asked multiple questions, we will solve the first question for you. If youwant any…

Answered: 1. A feeder is made up of three…

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter20: Special-purpose Outlets For Ranges, Counter-mounted Cooking Unit , And Wall-mounted Oven

Section20.1: Counter-mounted Cooking Unit Circuit

Problem 4R

See similar textbooks

Similar questions

:Two circuits are arrange as shown in figure (1), (a and b) each one of them has two identical conductors, the vertical distance between each conductor in the same circuit is 1 m, the distance horizontlly between circuits is 30 cm, take 1 cm as diamter for each conductors. Derermine the inductance per km of the double circuit ? a a' b' FIGURE (1) --
b) Why Generation Voltage Levels are low in the range of 11 kV/ 33 kV etc? c) Why ACSR Conductors are preferred over Copper Conductors?
Most residential general lighting circuits are wired with 14-AWG copper conductors and are protected by 15-amp circuit breakers. However, there are many electricians who install 12-AWG copper conductors and protect them with 20-amp circuit breakers. How will you know which conductor size and which circuit breaker size will be used for the general lighting branch circuits in the house you are wiring?
What is the rated amps city per phase for six No. 3 THHN copper current-carrying conductors with two conductors per phase (parallel) and all conductors installed in the same conduit
Single core cable design for 25 kV. The radius of conductor is 0.5 cm. The insulation material consists of two layers. The thickness of each layer is 2 cm. The voltage of first and second layers are 20 kV, 5 kV respectively. The minimum Electric stress of the cable is
What is the minimum trade size PVC conduit to contain 201 #12AWG TW75 Copper conductors.
3. What are the classifications of Core Loss and Copper Loss?
A set of conductors is used to supply residential unit with a total load current of 60 A at a single-phase supply voltage of 230 V. What would be the minimum size of the conductor to be used to achieve at least 5% voltage drop? The total conductor length is 300 ft. ..
Conductors with a -2 insulation designation have a (higher) (lower) ampacity in a wet location than do conductors without the designation. For the same size of conductor, aluminum conductors have a (higher) (lower) ampacity then do copper conductors.
The following problems refer to grounding requirements. 1. What is the minimum size copper grounding electrode conductor for a service with three sets of parallel 350 kcmil conductors (three conductors per phase)?
What is the voltage rating of the conductors in Type NMC cable? _______________
Define service-drop conductors.

SEE MORE QUESTIONS

Recommended textbooks for you

EBK ELECTRICAL WIRING RESIDENTIAL

Electrical Engineering

ISBN:

9781337516549

Author:

Simmons

Publisher:

CENGAGE LEARNING - CONSIGNMENT

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

EBK ELECTRICAL WIRING RESIDENTIAL

Electrical Engineering

ISBN:

9781337516549

Author:

Simmons

Publisher:

CENGAGE LEARNING - CONSIGNMENT

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS