(1) In an ammonia refrigeration system, the capacity is 210 kW at a temperature of-20°C. The vapor from the evaporator is pumped by one compressor to the condensing pressure of 1431 kPa. Later, the system was revised to a two-stage compression operating on the cycle shown below with intercooling but no removal of flash at 555 kPa. (a) in the original system. (b) compressors in the revised system. Calculate the power required by the single compressor Calculate the total power required by the two-

(1) In an ammonia refrigeration system, the capacity is 210 kW at a temperature of-20°C. The vapor from the evaporator is pumped by one compressor to the condensing pressure of 1431 kPa. Later, the system was revised to a two-stage compression operating on the cycle shown below with intercooling but no removal of flash at 555 kPa. (a) in the original system. (b) compressors in the revised system. Calculate the power required by the single compressor Calculate the total power required by the two-

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter45: Domestic Refrigerators And Freezers

Section: Chapter Questions

Problem 13RQ: Condensers in these refrigerators are all_______cooled.

See similar textbooks

Similar questions

For a 10 ton capacity refrigeration system, the pressure of refrigerant in the evaporator is 210 kPa, whereas in the condensor it is 900 kPa. If refrigerant R-134a is used under saturated conditions, calculate the theoritical power required to operate the compressor (kW)
For a 10-ton-capacity refrigeration system, the pressure of refrigerant in the evaporator is 150 kPa, whereas in the condenser it is 950 kPa. If refrigerant R-134a is used under saturated conditions, calculate the theoretical power required to operate the compressor = ... KW
For a 15 ton capacity refrigeration system, the pressure of refrigerant in the evaporator is 150 kPa, whereas in the condenser it is 1380 kPa. If ammonia (R-717) is used under saturated conditions, calculate the theoretical power required to operated the compressor (kW)
A refrigeration system with a capacity of 10 tons of refrigeration, operates at 210 kPa in the evaporator, while in the condenser it is 800 kPa. If R-134a refrigerant is in a saturated state, calculate the theoretical power required to operate the compressor. Compressor power = .... kW
For a 15 ton capacity refrigeration system, the pressure of refrigerant in the evaporator is 150 kPa, whereas in the condenser it is 1590 kPa. If ammonia (R-717) is used under saturated conditions, calculate the theoretical power required to operate the compressor (kW).
2. A refrigeration system with a capacity of 15 tons of refrigeration, operates at 150 kPa in the evaporator, while the condenser is 1450 kPa. If refrigerant R-717 is saturated, calculate the theoretical power required to operate the compressor. Compressor Power = Answer kW.
An ammonia refrigeration compressor takes its suction from the evaporator, at a temperature of-200F and a quality of 95%. The compressor discharges at a pressure of 100 psi, liquid ammonia leaves the condenser at 500F.(a)Determine the heat absorbed by the evaporator in kJ/kg. (b)Determine the heat rejected to the condenser in kJ/kg. (c)Determine the COP. (d)Determine the horsepower per ton of refrigeration. (e)Determine the quality of refrigerant upon entering to the evaporator
Determine the coefficients of performance of the refrigeration cycle.
Steam is delivered to turbine at 5.4 MPa and 600 degree C. Before condensation at 31 degree C, steam is extracted for feed water heating at 0.6 MPa. The turbine exhaust is 60 degree C. the required values of some state point properties are tabulated below. 7. Determine the quality of steam at the condenser inlet.
Q.1. A refrigeration process with interstage cooling uses refrigerant HFC-134a, and the outlet of the condenser is to be saturated liquid at 40°C. Refer to the following figure for stream numbers in your solution. The pressure of the flash chamber and the intermediate pressure between compressors is to be 290 kPa. The evaporator is to operate at -20°C and the outlet is to be saturated vapor. The flowrate of stream 1 is 23 kg/h. The flash chamber may be considered adiabatic. The compressors may be considered to be 80% efficient. a) What is the power input required to the first compressor? b) What are the flowrates of streams 6 and 7? What is the enthalpy of stream 4? Hot Side 6 5 Condenser 2nd Stage Compressor Throttle Valve 7 Flash Chamber Vapor Phase Only 1st Stage Compressor 8 Throttle Valve Evaporator 1 2 Cold Side
A refrigeration system using R22 is to have a refrigerating capacity of 60 kW. The evaporating temperature is -5degC and condensing temperature of 35 deg-C. Determine the volume flow rate of the refrigerant at the inlet to the compressor, the power required by the compressor, and the fraction of vapor in the mixture at the entrance to the evaporator. Use the spreadsheet to solve this problem.
There are removed 3.06 m3/s of vapor from the water evaporator of a vacuum refrigeration system: the warm water enters the evaporator at 18oC and chilled water leaves at 10oC, make-up water enters at 29o Determine the refrigerating capacity