1)Findtheinductance'L' and the currentunknownflowing through the first andthird arm Il & I3anderson bridge given below.If Z1of anhas resistor 5KQ, Z2detectorRyhas resistor &8.6 KQ, Z3 hasresistor 9.0 KN, Z5 hasresistor 6.2 KN the bridge hasa capacitor 2µf and thecurrent flowing through thesecond armR312 is 2.6mA.Take frequency as 100HZ.INNAH LECTRER-E STION

Given: The circuit for the Anderson bridge is shown below: Here R1=5 kΩR2=8.6 kΩR3=9.0 kΩR5=6.2…

1) Find the inductance'L' and the current unknown flowing through the first and third arm I1 & 13 of an anderson bridge given below. If Z1 has resistor 5K2, Z2 has resistor 8.6 KQ, Z3 has resistor 9.0 KQ, Z5 has resistor 6.2 K the bridge has capacitor 2uf and the current flowing through the 12 is 2.6mA. Take frequency as 100HZ. nadetuctor Riy a IV second arm AC

1) Find the inductance'L' and the current unknown flowing through the first and third arm I1 & 13 of an anderson bridge given below. If Z1 has resistor 5K2, Z2 has resistor 8.6 KQ, Z3 has resistor 9.0 KQ, Z5 has resistor 6.2 K the bridge has capacitor 2uf and the current flowing through the 12 is 2.6mA. Take frequency as 100HZ. nadetuctor Riy a IV second arm AC

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter19: Capacitors

Section: Chapter Questions

Problem 2PA: You are an electrician working in an industrial plant. You discover that the problem with a certain...

See similar textbooks

Similar questions

You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
For the following circuit, Vsrc=1.5 V and Rload%3D225 Q. What is Is? Is +. Vsrc VR Rload 30 mA 9 mA 6.67 mA 40 mV
A capacitor in series with a 20-KO resistance across a 10 V ac source. What size C is needed for equal voltage across R and Xc at frequency of 100 Hz and 100 KHz.
A capacitor C with 1 mF is charged by a constant voltage source (U). Source and capacitor are connected by a resistor R with 10 ko. To discharge the capacitor the source is replaced by a short. U R 1 R charging discharging The voltage source is replaced by a constant current source with an output of 1 mA. Please draw the voltage at the capacitor qualitatively over the time.
A resistor of 20ohms and a capacitance of unknown value when connected. In in parallel across a 100V, 50Hz supply take a current of 6A. The combination is now connected across a 100V supply of unknown frequency and the current falls to 5.5A . What is the frequency?
/Q6 The potential at point P due to Q1 and * :Q2 is = 1x10-12C 0.5 m 0.5 m Q2 = 1x10-12C %3D 50 cm P. 0.01797 V O -0.01271 V O ov O 0.01271 V C 10
A series R–L–C circuit comprises a 5µF capacitor, a 4ohm resistor and a variable inductance L. The supply voltage is 10∠0◦ V at a frequency of 159.1 Hz. The inductance is adjusted until the p.d. across the 4 ohm resistanceis a maximum. Determine for this condition (a) the value of inductance, (b) the p.d. across each component and (c) the Q-factor of the circuit.
Original Schematic and OrCAD Schematic: The input primary voltage is 250V, frequency 50 Hz, primary inductance setting is 2000H and secondary inductance is 10H and voltage peak to peak ripple is approximately equal to 92mv. U1 D4 IN our DINA002 C3 DIN002 90u R1 R2 10k TXI BC540A V1 VOFF =0 VAMPL 2 FREQ- 50 AC0 XFRM_LINICT-SEC D5 DIN4002 C2 0.384m 84 5 HH
The magnitude of the voltage applied to the electrodes of a welding machine can be adjusted in the circuit below. In the range of minimum and maximum value that variable value resistor can take What is the time interval that the capacitor will charge from 0 to 8 V?
An alternating voltage is applied to a series circuit consisting of a resistor and iron-cored inductor and a capacitor. The current in the circuit is 0.5 A and the voltages measured are 30 V across the resistor, 48 V across the inductor, 60 V across the resistor and inductor and 90 V across the capacitor. Find (a) the combined copper and iron losses in the inductor (b) the applied voltage.
An alternating voltage is applied to a series circuit consisting of a resistor and iron-cored inductor anda capacitor. The current in the circuit is 0.5 A and the voltages measured are 30 V across the resistor,48 V across the inductor, 60 V across the resistor and inductor and 90 V across the capacitor.Find (a) the combined copper and iron losses in the inductor (b) the applied voltage Answer: [(a) 3.3 W (b) 56 V]
An alternating voltage is applied to a series circuit consisting of a resistor and iron-cored inductor anda capacitor. The current in the circuit is 0.5 A and the voltages measured are 30 V across the resistor,48 V across the inductor, 60 V across the resistor and inductor and 90 V across the capacitor.Find (a) the combined copper and iron losses in the inductor (b) the applied voltage.Answer: [(a) 3.3 W (b) 56 V] Note: Please provide a clear solution!