1) Determine magnitude of the force the load creates in member FB, which contains the hydraulic cylinder H Express your answer to three significant figures and include the appropriate units. 2) Determine magnitude of the force the load creates in member BD. Express your answer to three significant figures and include the appropriate units.

Q: 18. 1.34 kg gas (R = 0.189 kJ/kg K, k = 1.288) in a Tank initially at 70°C is stirred by a paddle.…

A: Given data,  m = 1.34 kg R = 0.189 kJ/kg.K k = 1.288 T1 = 70°C = 343 K Qrej = - 102 kJ dS = 0.66…

Q: Determine the kinematic viscosity (Stokes) of oil having the relative density as 0.87. The shear…

A: According to the given data S.G=0.87 τ=1.61 N/m2 dVdS=0.23 We need to find (i) The viscosity (ii)…

Q: The plate is acted on by four parallel forces, three of which are shown. The fourth force P and its…

A: GivenThe resultant P=-1100i+1500j lb ft

Q: 8. In the assembly, the type of mating or fit between two parts includes clearance fit, interference…

A: There are three types of fits: (i) Clearance fit (ii) Transition fit (iii) Interference fir C :…

Q: 4.25 An automobile, having a mass of 1000 kg, runs over a road bump of the shape shown in Fig. 4.49.…

A: Given, The mass of the automobile, m = 1000 kg The speed of the automobile, v = 50 km/h = 13.88 m/s…

Q: Explain what engineering hypothesis testing is and how it pertains to engineering education.…

A: Engineering hypothesis testing is a process used in engineering to verify the validity of a…

Q: It can be shown that the point of the highest stress is on the outside of the shaft, just next to…

A:

Q: Find the reaction Cy following indetermine structure By Force method • Based on conjugate…

A:

Q: The beam in (Figure 1) is made from three boards nailed together as shown. Figure 20 mm 200 mm M 25…

A: Given data :- Bending moment = 460 N-m Find :- The resultant force that the bending stress will…

Q: What is the difference between laminar and turbulent flow, and how does this affect fluid mechanics…

A: In fluid mechanics, laminar and turbulent flow are two types of fluid flow that have different…

Q: Joint O of a space frame is supported by spring OA and is subjected to three member forces. Member 1…

A:

Q: Problem 3. The stress tensor has the following form: σij [80 3 02 0 13 0 16 Check if stresses {2, 7,…

A: Given σij=8030203016 Solution: To determine the principal stresses of the given tensor , the eigen…

Q: Q1. State whether each of the two statements included in your input values for Q1 are true or false:…

A: We will answer the first question. Please resubmit the question which you would like to be answered…

Q: Determine the force in each member of the truss. A 3 m 5 kM

A:

Q: A 0.25 m^3 rigid tank contains refrigerant-134a at 0.8 MPa and 100 percent quality. The tank is…

A:

Q: 1 - Use double integration to determine the elastic curve of a simply supported beam under a…

A:

Q: The solar energy collector design shown below has been used for agricultural applications. Air is…

A: Write the all three types of heat transfer processes. (1) Conduction (2) Convection (3) Radiation

Q: • A barge is pulled by two tugboats. If the resultant of the forces exerted by the tugboats is 5000…

A: According to the given data R=5000N α=45° We need to find Force in the member 1 and 2

Q: Could you explain further on how you got the value for U3? Im confused on what to interpolate.

A: The given information in the problem is shown in the following attached image:

Q: What are the characteristics of open loop backlash compensation method?

A: To find: The characteristics of open loop backlash compensation method.

Q: Determine the reactions at pin A and rollers B and C of the continuous beam shown below.

A: Draw the free-body diagram of the beam.   We need to find reactions

Q: Air enters into a nozzle at 4 bar and leaves at 1 bar, 350 °C and 700 m/s. Determine temperature of…

A:

Q: A T-shaped cross-section beam is loaded as shown in Figure P8.11. Find the maximum tensile and…

A: Given: The moment at C, M = 20 kN.m The force at C, P = 30 kN

Q: When considering the buckling of a column, the radius of gyration of its cross section, r, should be…

A: To find: The correct option.

Q: 6. A hollow shaft is to be designed to carry 10 kN normal load. Determine the inner diameter given…

A:

Q: 2.2 An oven whose thickness of side wall is 82.5mm has a thermal conductivity of wall insulation of…

A: (2.2) To find: The area of the wall surface. Given: The thickness of the side wall is L=82.5 mm1…

Q: Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ = 4450 mm² and an…

A: According to the given data σAB=165 MPa and AAB=4450mm2 σBC=100MPa and ABC=4400mm2 We need to find…

Q: Calculate the reaction at the pinned wall joint and the tension in the cable for the system shown.…

A:

Q: 1. At what flow angle will the flow become just sonic downstream of the nozzles of a high pressure…

A: Given: The shroud diameter ds=250 mm=0.25 m The hub to shroud diameter ratio r=0.8 The stagnation…

Q: A uniform circular rod with a weight of 8 lb and radius of 10 in. is attached to a pin at Cand to…

A: Given data: Radius, r = 10 in weight, W = 8 lb   Solution: The centroid location from c is given by,…

Q: Directions: modify the standard SolidWorks ANSI B Landscape layout for your own engineering…

A: To determine: Personalized layout/template of the the standard SolidWorks ANSI B Landscape layout…

Q: Member AB has a uniform rectangular cross section of 10 24 mm. For the load Q=8 kN, determine the…

A:

Q: Compute the reduced compliance [S] matrix for a lamina with E1 = 35 GPa, E2 = 3.5 GPa, V12 = 0.3,…

A: Write the given data. E1=35 GPa E2=3.5 GPaν12=0.3G12=1.75 GPaG23=0.35 GPa

Q: Two rigid tanks are connected by a valve. Tank A contains 0.6 m^3 of water at 330 kPa and 90 percent…

A: Solution: Given Data: VA=0.6 m3PA=330 kPaxA=0.9VB=0.5 m3PB=250 kPaTB=250oCT∞=25oC   To Find: (a) The…

Q: a) What fraction of the radiation is from 0 to 4 micrometers? What would the fraction be from 4 to 6…

A: Given: The surface temperature Ts=300 K ε1=0.75, ε2=0.1, ε3=0.8

Q: a) Find the transfer function F₁(s) = 01(s)/T(s) of the rotational system. Consider the initial…

A: Given: To find: Transfer function

Q: 20. A certain gas steadily flows through a engine at constant temperature of 400 K. The exit…

A: To find: The work of the steady flow. Given: The temperature is T=400 K. The inlet pressure is…

Q: Consider a crate supported by three cables AC, AB and AD as shown.What is closest to the maximum…

A: According to the given data A=(0 , -60 , 0) B=(-36 ,0 , -27) C=(0 , 0 , 32) D=(40 , 0 , -27) FAC=300…

Q: A motor (located at C) provides 50kW of power which is then used by pulleys A and B. When the motor…

A: GivenPC=50kWPB=30kWPA=20kWN=200 rpmd=5cm

Q: The four forces and geometry shown. The resultant force in x direction is: FBD at A To 75° 150° 30°…

A: According to the given data We need to find Resulting fore in the x-direction

Q: Q8. Determine the deflection of point B on the steel beam with I = 80×106 mm4 and E = 200 GPa. [Ans.…

A: GivenI=80×106 mm4=80×10-6 m4E=200GPa

Q: Could Dr. benjmin be lifted 20 cm above the floor by the thermal energy of the floor overcoming the…

A: Given Could Dr. benjmin be lifted 20 cm above the floor by the thermal energy of the floor…

Q: 3. A compound pendulum shown in Fig. 3 consists of a rod AB with mAB = mcD = 5 kg, and a disk with…

A: According to the question mD=5kg mCD=5kg mAB=10kg 1. The center of gravity G.  2 The mass moment of…

Q: Notes: a) b) c) A simplified sketch of the thermodynamic system showing cylinder/piston at initial…

A:

Q: (3.b) A converging-diverging nozzle is designed to expand air from a chamber in which the pressure…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam…

A:

Q: A cascade refrigeration system uses R22 in the low temp unit and R12 in the high temp unit. The…

A: To Find : The mass flow rate of R-22,R-12 Given : The power develops  is P=30 kW The temperature of…

Q: IfV1-72, V2-50 and 0-43° Determine the component about y of V2 (V2y) Va

A:

Q: Q6. Water flows at a in a specific rate in a horizontal pipe whose diameter is decreased by a…

A: Given data: d1 = 15 cm = 0.15 m = Initial diameter d2 = 8 cm = 0.08 m =  Final diameter P1 = 480 kPa…

Q: The d-diagram for a collagen fiber bundle from which a human tendon is composed is shown. If a…

A: Given: Tension in the tendon is, T=343.75lb Length of the tendon, L=6.5in Cross sectional area of…

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.