III. Theory/ Discussion1) Arduino IDE consists of 2 functions. What are they?a) else () and loop ()b) Setup () and build ()c) Setup () and loop ()d) Setup () and elseif ()2) When forward biased, LED emits light because of Recombination of carriers and Lightproduced by collisions.3) ATmega328p microprocessor is used in arduino UNO.(TRUE/FALSE)(TRUE/FALSE)IV. Circuit Diagram (Before Simulation)Draw the circuit and write the program codes by considering input pin as A2 and output and output pinas 9 for green, 10 for yellow LED & 11 for red LED. Also verify the results if (gas >= 100) red LED shouldglow, if (gas >= 60) yellow LED should glow, otherwise green LED should glow.V. Connection Diagram and Results after simulationhp

We are authorized to solve first three parts only. As you have not mentioned which part to solve.…

1) Arduino IDE consists of 2 functions. What are they? a) else () and loop () b) Setup () and build () c) Setup () and loop () d) Setup () and elseif () O When forward biased, LED emits light because of Recombination of carriers and Light produced by collisions. ATmega328p microprocessor is used in arduino UNO. (TRUE/FALSE) (TRUE/FALSE)

1) Arduino IDE consists of 2 functions. What are they? a) else () and loop () b) Setup () and build () c) Setup () and loop () d) Setup () and elseif () O When forward biased, LED emits light because of Recombination of carriers and Light produced by collisions. ATmega328p microprocessor is used in arduino UNO. (TRUE/FALSE) (TRUE/FALSE)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Explain quantization noise in PCM System, and how it can be minimized?
Create an Analog Signal Waveform that will enter in my 2 bit Flash ADC circuit. (Given Values are Vref:10v and Vin:5v) Please also show an explanation on how you got the Analog Signal Waveform by mathematical terms. (Show the formulas you will be using.)
5- Discuss the effect of changing the number of bits on the recovered analog waveform. 6- Discuss the effect of changing the frequency of input analog signal on the reconstructed analog output signal.
2) Convert Hexa-decimal to Octal a. 7E6A(16)=?(8) b. C350(16)=?(8) c. 9E36.7A(16)=?(8) d. EADD.EBEF(16)-?(8)
1) what is the Voltage & Current rating ofTriode for Alternating Current (TRIAC) 2) 5. Are the following statements correct or wrong? Justify your answer.(a) Thyristors are used only for low voltage, low current applications.(b) MOSFETs are used for high frequency applications.(c) BJT is more efficient than IGBT in high power applications.(d) GTO requires very low current applied to its gate to be turn off.(e) IGBT is a voltage driven device.
The output voltage of a single-phase full bridge voltage source inverter is controlled by unipolar PWM with one pulse per half cycle. For the fundamental rms component of output voltage to be 75% of DC voltage, the required pulse width in degrees (round off up to one decimal place) is
The current output of a successive approximative type ADC is showing as 110011. If the reference voltage to the ADC is 5V, what is the corresponding analog signal voltage input to this ADC? If the ADC were of 10 bits, would the conversion time be reduced? Please answer ASAP I will like it please ASAP...
Draw the circuit diagram of 4-bit Ripple Carry Adder. Page 6 of 8
5. MOSFET's can be either NMOS or PMOS and can also: a. Glow in the dark b. Come as Enhancement mode or Depletion Mode c. Make a noise when current flows d. Not be used as switches
6. Which of the following is not a type of signal is... a. analog signalb. Chain signalc. Binary signald. Dict signale. digital signal
Digital logic design Solution Needed
The required 7-segmrnt decoder should have 3-inputs (which are the bits of the binary number desired to be designed, call them A,B,C), and 7 outputs (the 7 segments of the display unit which are a, b, c, d, e, f & g). 8. gf a b t la Ob d Dp e d8c Dp The 7-segment to be used is of common anode type. Consequently, any segment will be ON if its input is Low, meaning that for displaying 0 the segments inputs (a,b,c,d,e,f.g) should be (0000001), or g will be OFF while all the others are ON. 1- Make a table explaining the inputs and the corresponding outputs for the 6 combinations input (000.101), assuming the other two combinations as don't care. 2- Find the output as a function of the inputs (A,B,C) using K-map to minimize the expressions 3- Show your design using 2-input, and 3-input NAND gates, and inverter.