022 Plate 3-Method of Consistent Deformation Determine the force in member CD of the truss shown in the figure. Circled values are areas in square inches. E is constant. FEU ALASAN PEU DELIMAN What is the horizontal Reaction at A? [Select] What is the Verticall Reaction at A? [Select] What is the Vertical Reaction at B? [Select] What is the horizontal Reaction at C? [Select] O II W -10 ft- D 30 k (2 ( Wo -15 ft S O C 20 ft C Technology Driven by Innovation 208C Light rain

022 Plate 3-Method of Consistent Deformation Determine the force in member CD of the truss shown in the figure. Circled values are areas in square inches. E is constant. FEU ALASAN PEU DELIMAN What is the horizontal Reaction at A? [Select] What is the Verticall Reaction at A? [Select] What is the Vertical Reaction at B? [Select] What is the horizontal Reaction at C? [Select] O II W -10 ft- D 30 k (2 ( Wo -15 ft S O C 20 ft C Technology Driven by Innovation 208C Light rain

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The question is: Determine the reaction magnitude at the beam support A for the given loading
Calculate reaction at supports
Determine the reactions by the method of consistency deformations. Select the reaction at the roller support to be the redundant. 90KN 60KN A 3m 3m D В 3m C E = 200 GPa I= 3.250x10^6 mm4
400mm Find the required spacing of intermediate stiffeners if V*=1600KN 25mm • Check the adequacy of a pair of stiffeners 90mmx12mm • Check the web crushing capacity if the reaction of 1600kN is applied over a stiff bearing length of 250mm at the end of the beam (note that the spread of stress can only go in one direction) • Homework extension: Check the adequacy of an endplate stiffener 300 wide by 16mm thick 12mm Use Grade 300 Steel 1440mm
Steel A-450 mm² E-200 GPa L-4.0 m A B opper A=230 mm² E-120 GPa L= 3.0 m 5.0 m a) What maximum P can be applied on the horizontal bar to give a stress of 110 MPa to steel and 150 MPa to copper. How far from copper should P be acting. Neglect the weight of the bar. b) What are the amount of deformations of the rods
P El is constant, find the reaction forces. Using the method of consistent deformations EI L 0.75L 2P 2EI 0.75L
The static indeterminacy of the structure shown below is Hinge - K I J H F E G A B D
The rigid bar ABCD supports point loads at A and D and is being supported by two bars at B and C. Determine the absolute value of the deformation at point C. (in mm) 120KN 4m 3m Sm A L= 6m 90 kN L-4m A= 0.04m A = 0.0 Gm² E=200 GA E=80 GPa
A rigid bar ABCD is supported by two bars as shown in the figure. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in rod (1) is -1260 μm/m. Determine the normal strain in rod (2) if there is a 1-mm gap in the connection at pin C before the load is applied. 1413 μm/m 1223 μm/m 1286 μm/m 738 μm/m 1553 μm/m
Compound axial member ABC has a uniform diameter of d = 1.25 in. • Segment (1) is an aluminum [E, = 10000 ksi] alloy. The length of segment (1) is L, = 70 in. • Segment (2) is a copper [E2 = 17000 ksi] alloy. The length of segment (2) is L2 = 98 in. When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of 8z = 2100 uin./in. in the longitudinal direction. What is the total elongation of member ABC? L2 Aluminum B Сорer Answer: in. AL = i
Compound axial member ABC has a uniform diameter of d = 1.25 in. • Segment (1) is an aluminum [E1 = 10000 ksi] alloy. The length of segment (1) is L1 = 100 in. • Segment (2) is a copper [E2 = 17000 ksi] alloy. The length of segment (2) is L2 = 140 in. When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of ɛ2 = 2300 uin./in. in the longitudinal direction. What is the total elongation of member ABC? L2 (1) Aluminum B (2) Copper Answer: in, AL = i
'bo Part A If it is made from a plate that has a constant width bo, determine the absolute maximum bending stress in the beam.