0.8 m 0.4 m В 0.6 m 1.6 m P = 1.2 kN 2 m The rigid beam AB is hinged to a support at A and supported by two vertical wires attached at points C and D. Both wires have a diameter of 2.5 mm and are made of steel with Est = 200 GPa. Determine the tensile stresses oc and Op in the wires due to the load P = 1.2 kN and find the downward displacement OB at end B of the beam. %3D

0.8 m 0.4 m В 0.6 m 1.6 m P = 1.2 kN 2 m The rigid beam AB is hinged to a support at A and supported by two vertical wires attached at points C and D. Both wires have a diameter of 2.5 mm and are made of steel with Est = 200 GPa. Determine the tensile stresses oc and Op in the wires due to the load P = 1.2 kN and find the downward displacement OB at end B of the beam. %3D

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.7P: Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and...

See similar textbooks

Similar questions

A steel column ( E = 30 X 103 ksi) that is fixed at the base and free at the top is constructed of a W8 x 35 wide-flange member (sec figure). The column is 9.0 ft long. The force P acting at the top of the column has an eccentricity e = 1.25 in. If P = 40 kips, what is the maximum compressive stress in the column? If the yield stress is 36 ksi and the required factor of safety with respect to yielding is 2.1, what is the allowable load Pallow?
A long re Lai nine: wall is braced by wood shores set at an angle of 30° and supported by concrete thrust blocks, as shown in the first part of the figure. The shores are evenly spaced at 3 m apart. For analysis purposes, the wall and shores are idealized as shown in the second part of the figure. Note that the base of the wall and both ends of the shores are assumed to be pinned. The pressure of the soil against the wall is assumed to be triangularly distributed, and the resultant force acting on a 3-meter length of the walls is F = 190 kN. If each shore has a 150 mm X 150 mm square cross section, what is the compressive stress
A column, pinned at top and bottom, is made up of two C 6 x 13 steel shapes (see figure) that act together. Find the buckling load (kips) if the gap is zero. Find required separation distance d(inches) so that the buckling load is the same in y and z directions. Assume that E = 30,000 ksi and L = 18 ft. Note that distance d is measured between the centroids of the two C shapes.
Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?
A metal bar is made out of A-36 steel and has a diameter d 20mm with the end at A fixed to the wall. There is are balanced axial loads at B of P₁ = 50 kN and a point load at C of P2 = 40 kN. The distance from A to B is L₁ = 600 mm and the distance from B to C is L2 400 mm. Calculate the displacement of point C relative to point A. The modulus of elasticity for steel is E = 200 GPa A d B The displacement at C is 8 = P₁ 1 Р1 с BY NO SA 2021 Cathy Zupke mm P2
1. Steel rod 2.5m long is secured between tow walls. If the load on the rod is zero at 200C, compute the stress when temperature drops to (-200C). The cross-sectional area of the rod is 1200 mm2 α=11.7μ m/(m.0C) and E=200 GPa. Solve assuming (a) that the wall is rigid and (b) that the wall spring together a total distance of 0.500mm as the temperature drops. 2. The rigid bar ABC in Figure is pinned at B and attached to the two vertical rods. Initially, the bar is horizontal and the vertical rods are stress-free. Determine the stress in the aluminum rod if the temperature of the steel rod is decreased by 40°C. Neglect the weight of bar ABC.
The rigid bar AB of negligible weight is supported by a pin at 0. When the two steel rods are attached to the ends of the bar, there is a gap D= 4 mm between the lower end of the left rod and its pin support at C. Compute the stress in the left rod after its lower end is attached to the support. The cross-sectional areas are 300 mm2 for rod AC and 250 mm2 for rod BD. Use E= 200 GPa for steel. lo/0 0.75 m 1.5m 2 m ANSWER: MPa
Clear my choice Let's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E= 200 Gpa and a Poisson's ratio of 0.3. If a tensile force Fis subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F. Select one: O F= 5236 N OF=15708N O F= 13090 N OF=10472 N OF=4189 N O F=6283 N Clear my choice Finish attempt NEXT ACTIVITY MENG360 Test -Spring 2020-2021 Jup to
The uniform 44 kN bar BC is supported by a pin at C and the aluminum wire AB. The cross-sectional area of the wire is 178.5 mm2. Assuming bar BC to be rigid, find the vertical displacement of B due to the weight of the bar. Use E = 71 GPa for aluminum. Anwer must be in mm.
The rigid bar ABC is supported by pin at A and aluminum wire BD, is horizontal before the Load P is applied. Find the vertical displacement of point C caused by the load P=35KN. Where E of aluminum equals 70GPA and the area of the wire is 200mm^2 -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.- Direction of the assumption of the equilibrium equation must be shown, no direction will be marked wrong.
4. The cable will fail when subjected to a tension of 8000 N. Determine the largest vertical load P the frame will support and compute theresultant internal loadings at the cross section through point C. Answer: P = 2133.33 N, Mc = 1600 Nm, Nc = 8000 N, Vc = 2133.33 N 0.1 m 0.5 m C 0.75 m- -0.75 m- -0.75 m-
A metal bar is made out of A-36 steel and has a diameter d = 23mm with the end at A fixed to the wall. There is are balanced axial loads at B of P₁ = 30 kN and a point load at C 35 kN. The distance from A to B is L₁ of P2 570 mm 390 mm. Calculate the = and the distance from B to C is L2 displacement of point C relative to point A. A L₁ ↑ d B L2 - P₁₁ Р1 С The displacement at C is 8 = -0.00306 d - cc 080 BY NO SA 2021 Cathy Zupke P₂ x mm