0.3MW / m3 heat is generated in a 6 cm thick flat wall. One surface of the wall is insulated and the other surface is exposed to an environment of 93C. The convection heat coefficient between the wall and the environment is 570 W / m2C and the heat conduction coefficient for the wall is 21 W / Since it is mC, calculate the maximum temperature (T0) inside the wall (C).

0.3MW / m3 heat is generated in a 6 cm thick flat wall. One surface of the wall is insulated and the other surface is exposed to an environment of 93C. The convection heat coefficient between the wall and the environment is 570 W / m2C and the heat conduction coefficient for the wall is 21 W / Since it is mC, calculate the maximum temperature (T0) inside the wall (C).

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.1P: A plane wall, 7.5 cm thick, generates heat internally at the rate of 105 W/m3. One side of the wall...

See similar textbooks

Similar questions

1.10 A heat flux meter at the outer (cold) wall of a concrete building indicates that the heat loss through a wall of 10-cm thickness is . If a thermocouple at the inner surface of the wall indicates a temperature of 22°C while another at the outer surface shows 6°C, calculate the thermal conductivity of the concrete and compare your result with the value in Appendix 2, Table 11.
Show that the rate of heat conduction per unit length through a long, hollow cylinder of inner radius ri and outer radius ro, made of a material whose thermal conductivity varies linearly with temperature, is given by qkL=TiTo(rori)/kmA where Ti = temperature at the inner surface To = temperature at the outer surface A=2(rori)/ln(ro/ri)km=ko[1+k(Ti+To)/2]L=lenthofcyclinder
A high-speed computer is located in a temperature-controlled room at 26C. When the machine is operating, its internal heat generation rate is estimated to be 800 W. The external surface temperature of the computer is to be maintained below 85C. The heat transfer coefficient for the surface of the computer is estimated to be 10W/m2K. What surface area would be necessary to assure safe operation of this machine? Comment on ways to reduce this area.
A plane wall, 7.5 cm thick, generates heat internally at the rate of 105 W/m3. One side of the wall is insulated, and the other side is exposed to an environment at 90C. The convection heat transfer coefficient between the wall and the environment is 500 W/m2 K. If the thermal conductivity of the wall is 12 W/m K, calculate the maximum temperature in the wall.
3.17 A 1.4-kg aluminum household iron has a 500-W heating element. The surface area is . The ambient temperature is 21°C, and the surface heat transfer coefficient is . How long after the iron is plugged in does its temperature reach 104°C?
1.29 A spherical interplanetary probe with a 30-cm diameter contains electronic equipment that dissipates 100 W. If the probe surface has an emissivity of 0.8, what is its surface temperature in outer space? State your assumptions in the calculations.
1.19 A cryogenic fluid is stored in a 0.3-m-diameter spherical container is still air. If the convection heat transfer coefficient between the outer surface of the container and the air is 6.8 , the temperature of the air is 27°C, and the temperature of the surface of the sphere is –183°C, determine the rate of heat transfer by convection.
A pipe carrying superheated steam in a basement at 10C has a surface temperature of 150C. Heat loss from the pipe occurs by radiation (=0.6) and natural convection (hc=25W/m2K). Determine the percentage of the total heat loss by these two mechanisms.
A resistor provide energy to a metal block 20 cm wide with a conductivity of 120 W/m.k. The temperature on the metal block near the resistor side is 70 oC. The heat travel to the other side of the block. On the other side, air is cooling the metal block. The convective heat transfer coefficient for air is 300 W/m2.k. Calculate the energy of the resistor in KW/m2 such that the air temperature near other side of the block is 0oC.
A large plate of 0.5 m thickness and constant thermal conductivity of k=60 W/m•K in which heat is generated uniformly at a rate of 2 kW/cm³. One side of the plate is heavily insulated so that there is no heat loss from the insulated side of the plate. The other side of the plate is exposed to the environment at T= 25°C with convection heat transfer coefficient is 20 W/m2-K. a) Express the differential equation and the boundary conditions for steady operating conditions. b) Determine the variation of temperature in the plate. c) Find the inner and outer surface temperatures of plate.
An industrial wall is constructed of 20 cm thick fireclay of thermal conductivity 1W/m 0C. This is covered on the outer surface with a 3 cm layer of insulating material of thermal conductivity 0.075 W/m0C. The innermost surface is at 940 0C and the outermost surface is at 40 0C . The steady state of heat transfer is occurring through the wall. So what is the rate of heat transfer rate that is occurring through the wall? What is the temp of the interface of these walls?
A cold-storage room is constructed of an inner layer of 11 mm of pine with thermal conductivity of 0.15 W/m K, and an outer layer of 75 mm of concrete with thermal conductivity of 0.75 W/m K. The wall surface temperature is 253 K inside the cold room and 299 K at the outside surface of the concrete. Calculate the heat loss in W per 1 m2. Please keep one decimal and take positive value for the final answer.