.382 cm. and a m aluminum wire of unknown length has a diameter of -esistance of .295 ohm. By several successive passes through drawing dies the radius of the wire is reduced to 078 CM. as increased by 23.6 % in the drawing process, calculate the resistance of the reduced size wire. Assuming its resistivity

.382 cm. and a m aluminum wire of unknown length has a diameter of -esistance of .295 ohm. By several successive passes through drawing dies the radius of the wire is reduced to 078 CM. as increased by 23.6 % in the drawing process, calculate the resistance of the reduced size wire. Assuming its resistivity

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 14RQ

See similar textbooks

Similar questions

What is meant by sheet resistivity, and how does this differ from the resistivity of a material? What are the units for sheet resistivity?
A-How temperature affects the conductivity of conductive metals and how it affects semiconductors.semiconductors B-What is superconductivity, how does it relate to temperature? Some examples of superconductors.superconductors.
A wire of 59 in length and 4 mm2 has a resistance of 0.94 ohms. A 110-m length of wire of the same material has a resistance of 3 at the same temperature. Find the radius of this wire. The final unit must be in millimeter, mm.
Nichrome ribbon resistor elements each has a resistance of 1 ohm. The element is made from sheet of nichrome alloy, 0.025 cm think. If the width of the ribbon is 0.3cm, what length is required per element in cm? Assume specific resistance of nichrome alloy to be 109microOhm-cm.
Discuss the variation of resistivity with temperature for insulators, semiconductors and conductors. Support your discussion with resistivity versus temperature graph/curves
Nichrome ribbon resistor elements each has a resistance of 1 ohm. The element is made from sheet of nichrome alloy, 0.025cm thick. If the width of the ribbon is 0.3cm, what length is required per element? Assume specific resistance of nichrome allow to be 109micro ohm-cm.
Identify elements that are in parallel a. in Figure P1.37, b. in Figure P1.43, c. in Figure P1.44.
PROBLEM 2 Two semiconductor materials A and B shown in the given figure, are made by doping germanium crystal with arsenic and indium respectively. The two are joined end connected to a battery as shown in figure. Is the junction forward biased or reverse biased? A B
Each of three insulators forming a string has self-capacitance of "C" farad. The shunt capacitance of each cap of insulator is 0-25 C to earth and 0-15 C to line. Calculate the voltage distribution across each insulator as a pecentage of line voltage to earth and the string efficiency.
What is extrinsic semiconductor? Mention explain its formation with suitable diagram. (a) Write any five differences between Conductor, Semiconductor ind Insulator.
Problem A potentiometer is an instrument for measuring an unknown voltage in comparison to a standard voltage. In the potentiometer shown in Figure 1.0 a 16.0-m stretch of wire AB is connected to a 9.00-V battery. The resistance per unit length of the wire is 16.0 0/mm. The movable contact P is at point B. An ammeter (circle with A inside) is connected to point A. 16.0 m A B www Figure: 1.0 A V = 9.00 V
We want to investigate how the field strength will be with air as dielectric and with steatite. A plate capacitor is placed in a 24 kV network between phase and ground. The relative permittivity of air is &=1 and for steatite &-6. The plate capacitor has area = 1m². The distance between the electrodes is 2 mm. Ep = 8.854-10-12 F/m A=1m² d=2mm a) Calculate the maximum field strength in the plate capacitor. (Answer: 9.8kV/mm) b) What is the capacitance of the capacitor if we use steatite? (Answer: C = 26.6nF)