. Explain the reason for the following rules: a. Always set the micropipette within its designated range f. Always watch to see the solution enter the tip g. After expelling liquid, always hold the plunger at the second stop while removing the pipette from the liquid h. Always balance a centrifuge before turning it on

. Explain the reason for the following rules: a. Always set the micropipette within its designated range f. Always watch to see the solution enter the tip g. After expelling liquid, always hold the plunger at the second stop while removing the pipette from the liquid h. Always balance a centrifuge before turning it on

Biomedical Instrumentation Systems

1st Edition

ISBN:9781133478294

Author:Chatterjee

Publisher:Chatterjee

Chapter9: Instrumentation In Blood Circulation

Section: Chapter Questions

Problem 8P

See similar textbooks

Similar questions

Explain the reason for the following rules: a. Always hold a loaded micropipette in a vertical positione. Always release the plunger slowlyf. Always watch to see the solution enter the tip
Explain the reason for the following rules:a. Always set the micropipette within its designated rangeb. Always push (or twist) the tip securely onto the micropipettec. Always push the plunger to the first stop before entering
6. Given the following scenarios, identify all possible causes of the problem and offer at least two alternative solutions to correct each problem. A. Rimmention B. Ma S ATALA You turn on an electrical suction machine and it does not work. IMMATER Jiltransdated The suction is lost while suctioning a patient. Mac
4. If you wanted to measure out the following volumes using micropipettes, which one would you use AND what would the dial read? Volume Micropipette to use Setting 0.5 mL 25 μι 100 μι 975 µl
(e) Complete the following table: Number printed on the micropipette's end (its plunger) 20 20 200 1000 1000 Number showing in the micropipette's display window OTOHOSHOSHOOO 0 7 0 1 0 5 1 0 5 1 0 0 0 2 1 Volume that the micropipette is set to draw up (include units in your answer) 6) Before using a micropipette, you have to first place a 7) Shown below are the steps required to transfer fluid from one tube to another using a micropipette. Write numbers in the blanks to indicate the correct order in which the steps should be performed. Slowly release the micropipette's plunger. Place the micropipette tip into the tube containing fluid you wish to draw up. Push down on the micropipette plunger until it reaches the second stop. Place the micropipette tip into the tube that you wish to expel fluid into. Push down on the micropipette plunger until it reaches the first stop. 8) Suppose that you're getting ready to draw fluid into a micropipette. To do so, you push the micropipette's plunger…
is a device used in the laboratory to transfer small 1 point quantities of liquids O Micropipette All are correct Tips O Dropper Clear selection 1 point
1. Dr order 1000 mL D5W to run for 8 hrs. drip factor 15 gtt/mL. caculate driprate
6. The following data were obtained after a short-term infusion. Calculate the AUC; and AUC2. Time (h) [Drug] (mg/l) 1 10 15 3 18 4 4 6 2
1 2 3 1 point Mike needs to pipette 25 uL of solution. Which pipette should he use to pipette the most accurate amount of solution? P1000 OP20 1 point You need to pipette a solution of 150 uL. What pipette will you use? What will you set this pipette to (i.e. what will the numbers read on the pipette?) P1000; 0150 2000 P10 P200 ▶⠀ ⠀ > > n P10; 015 1 point Which of the following are best practices for using a micropipette? Select all that apply. Never exceed the upper or lower limit of the pipette If only pipetting a little extra, use a pipette outside of the range limit Point the pipette tip upwards Use a new tip for different liquids When withdrawing liquids, always release the plunger slowly P200; 150 P20; 150