Synthesis of Isopentyl Acetate (Banana Oil) Using a Fischer Esterification Reaction Zhenshu Wang (Stan) TA: Aaron League September 23, 2012 Purpose: The purpose of the experiment was to perform the acid-catalyzed Fischer Esterification of acetic acid and isopentyl alcohol to form isopentyl acetate, or banana oil, which is used in flavor industries. The equilibrium of the reaction was changed by adding an excess amount of acetic acid. The reaction was refluxed and product was purified by extraction and distillation. Isopentyl acetate was analyzed by infrared spectroscopy and 1H NMR spectroscopy. Reaction Scheme: Mechanism: Key features of the Fischer Esterification mechanism are: a. protonation of the carbonyl group, b. the …show more content…
The boiling point was 129 oC which was lower than the literature boiling point, 142 oC. Analysis by infrared spectroscopy showed the impurity (most likely CH2Cl2) containing a carbon-chlorine bond. A good yield of isopentyl acetate was obtained during this experiment. Loss of the product was likely through transferring liquid from separatory funnel to the Erlenmeyer flask and residual material left in the distillation flask. Using an organic solvent like benzene or cyclohexane as a transfer agent would improve the yield, since their boiling points were around 80 oC and could be easily separated from the final product through simple distillation. However this
A sample of ethyl ethanoate was prepared. The sample which was prepared was not pure. The boiling point of ethyl ethanoate is 77.1. If the boiling point of the sample produced is less than 77 it means that it has some impurities. If the sample has a boiling point more than 77 it also means it has more impurities. A sample is pure if the boiling point of the sample is 77.1. Purity of a sample can be determined by the boiling point of a liquid. Different liquids have different melting and boiling points. If the liquid is impure there would be a change in the melting and boiling points which determines that it has some impurities.
The goal of this experiment was to synthesize aspirin. In this experiment aspirin, also known as acetylsalicylic acid, was synthesized from salicylic acid and acetic anhydride. In the reaction the hydroxyl group on the benzene ring in salicylic acid reacted with acetic anhydride to form an ester functional group. This method of forming acetylsalicylic acid is an esterification reaction. Since this esterification reaction is not spontaneous, sulfuric acid was used as a catalyst to initiate the reaction. After the reaction was complete some unreacted acetic anhydride and salicylic acid was still be present in the solution as well as some sulfuric acid, aspirin, and acetic acid. Crystallization, which uses the principle of
Abstract: One mixture of two unknown liquid compounds and one mixture of two unknown solid compounds were separated, isolated, purified, and characterized by boiling point. Two liquid unknowns were separated, isolated, and purified via simple distillation. Then, the process of an acid-base extraction and washing were used to separate two unknown compounds into two crude compounds: an organic acid and a neutral organic compound. Each crude compound was purified by recrystallization, resulting in a carboxylic acid (RCO2H) and a pure organic compound (RZ). The resulting mass of the pure carboxylic acid was 1.688g with a percent recovery of 31.80%, the boiling range was 244-245 °C, and its density was 2.0879g/mL. The resulting mass of the pure organic solid was 2.4902g with a percent recovery of 46.91%, the boiling range was 52.0-53.4°C, and its density was 1.5956 g/mL.
1.5mL of phosphoric acid including 3-4 boiling chips were also added to the 25mL flask. The short path distillation apparatus was set up as shown in Figure 1. A heating mantle was used to heat up the 25mL flask. The solution was distilled to the receiving flask until a small amount of liquid remained in the initial RBF flask. At this point the presence of thick grey smoke pulling over into the entire apparatus was observed. The apparatus was then left to cool down. Through the use of pasture pipette, the aqueous layer from the distilled solution was drawn out. Sodium carbonate was then added to the remaining organic solution in order to check the pH and to verify the basicity of the solution. The aqueous layer was again drawn out from the solution. Next, 0.5g of sodium sulfate was added to the remaining organic layer and was swirled until the liquid appeared to be dry and clear. The alkenes were transferred into a clean 10mL flaks using another clean pasture pipe. The apparatus from the first distillation was rinsed off with
In this experiment, the Fischer Esterification of an unknown acid and an unknown alcohol was used to prepare an unknown ester. Sulfuric acid was used as a catalyst in the reaction which then was put under reflux. After cooling, the pH of the solution was raised to approximately 8 using sodium carbonate. Diethyl ether was added, then the aqueous layer was removed and the organic layer was washed with sodium chloride. The aqueous layer was removed again and sodium sulfate was added. The unknown product was then identified using gas chromatography (GC) to obtain the retention time.
In the process, extraction and distillation techniques were used. The theoretical amount of t- pentyl chloride was 17.358g, while 15.78 g was the actual amount produced which gave a percent yield of 90.9%. An error occurred while performing the experiment, the filtered dried product in the distillation process was placed in the wrong flask. Due to this that part of the experiment had to be redone and the new filtered product had some aqueous solution in it, which caused the boiling point to be under the specified temperature. The boiling point then was at 50 ℃ compared with the expected range of 79- 84 ℃. The IR spectrum used above was from another group’s results. The experimental IR spectrum has more prominent peaks in the 3000 cm-1 range compared to the expected IR spectrum. Nonetheless, the experimental IR spectrum resembles the expected IR spectrum in the sense that the peaks are closely around the same wavenumber range. This is probably due to the product being distilled at the right boiling
A small beaker was placed under the arm of the distillation head to catch the distillate. Foil was wrapped around the neck of the round-bottomed flask and a wet paper towel was wrapped around the arm of the distillation head to create a condenser. The flask was heated gently so that the distillate dropped at a rate of two drops per minute. The temperature was recorded as every drop was collected. The distillation began at around 55.0 ℃. The distillation was stopped after 29 drops were collected to prevent the solution from being distilled to dryness. See attached data. The known boiling point of 1-butanol is 117.5 ℃ (Lemonds). The known boiling point of 1-propanol is 97 ℃ (Thiyagarajan). The known boiling point of acetone is 56 ℃ (Forss). The known boiling point of 2-butanone is 79.6 ℃ (Jiang). For unknown #3 the boiling point of the first substance seemed to be around 56 ℃ and the boiling point of the second substance seemed to be around 111 ℃. Therefore unknown #3 seemed to be a mixture of acetone and 1-butanol.
Discussion: As seen in the melting point determination, the average melting point range of the product was 172.2-185.3ºC. The melting points of the possible products are listed as 101ºC for o-methoxybenzoic acid, 110ºC for m- methoxybenzoic acid, and 185ºC for p- methoxybenzoic acid. As the melting point of the sample
In this experiment, the main objective was to synthesize a ketone from borneol via an oxidation reaction and secondly, to produce a secondary alcohol from camphor via a reduction reaction. Therefore, the hypothesis of this lab is that camphor will be produced in the oxidation reaction and isoborneol will be the product of the reduction reaction because of steric hindrance. For the oxidation step, a reflux will be done and then a microscale reflux for the reduction step. The products will be confirmed using Infrared spectroscopy, the chromic acid test, 2,4-DNP test and 13C NMR spectroscopy. The results of this
The products of interest within this experiment are 2-methyl-1-butene and 2-methyl-2-butene from sulfuric acid and phosphoric acid catalyzed dehydration of 2-methyl-2-butanol. The reaction mixture was then separated into its separate alkene components by steam distillation and then analyzed by gas chromatography (GC), Infrared Radiation (IR) spectroscopy, and Nuclear Magnetic Resonance (NMR) imaging. Gas chromatography is an analytical technique that is able to characterize if specific compounds exist in a reaction mixture, even if they are in low quantities, assess how much of a compound exists within a reaction mixture relative to other components within the sample, and determine the purity of an isolated product. In the case of this experiment, gas chromatography is used to analyze how pure the alkene reaction sample was and if any remnants of impurities or 2-methyl-2-butanol remained in the sample after isolation of alkene components.
The boiling range of the 1-pentyl ethanoate distillate was approximately between 149-151°C. This was indicated by the formation of the distillate and when the mixture of the purified 1-pentyl ethanoate started to vigorously
Before the start of the experiment, the theoretical yield was to be calculated. First, the limiting reagent was determined from the reagents by comparing the amount of moles. Among the three reagents involved in this experiment - camphor, sodium borohydride, and methanol, camphor was found to be the limiting reagent. The moles of camphor was less than the combined moles of the other two reagents. The theoretical yield, which is the amount of product that could be possibly produced after the completion of a reaction (“Calculating Theoretical and Percent Yield”), was found to be 0.25 g. Once the product was achieved, a percent yield of 97% was determined. As a result, the reduction of camphor to isoborneol was successful.
An ester was synthesized during an organic reaction and identified by IR spectroscopy and boiling point. Acetic acid was added to 4-methyl-2-pentanol, which was catalyzed by sulfuric acid. This produced the desired ester and water. After the ester was isolated a percent yield of 55.1% was calculated from the 0.872 g of ester recovered. This quantitative error was most likely due to product getting stuck in the apparatus. The boiling point of the ester was 143° C, only one degree off from the theoretical boiling point of the ester 1,3-dimethylbutyl, 144 ° C. The values of the
In this experiment, a Fischer Esterification reaction was performed with two unknown compounds. The unknown compounds, Acid 2 and Alcohol D, were identified by using the knowledge of the reaction that took place, and the identity of the product that was synthesized. The identification of the product resulted from analysis of IR and NMR spectra.
The Cativa process is reported to give an acetic acid yield of 98% and operating savings of 10–