Step 1: Remove Parts Open the back cover of the cellphone. Pull out the battery of the cellphone, SIM card and Memory card. Step 2: Remove connector panel Take out the connector panel with a pair of tweezers. There should be enough sticky to re-adhere the panel upon reassembly, otherwise use a small amount of double-stick tape. Use the sharp tip of a spudger tool to detach the home button cable connector from socket. Step 3: Detach front panel Note: These cables are thin and effortlessly damaged, therefore be sure that you are only stripping off the display assembly and not cut them. Carefully remove the front panel from the cellphone with the use of opening pick tool. As shown in picture 3. Step 4: Remove the screws Flip the phone and take …show more content…
(n.d.). Samsung Galaxy S5 Battery Replacement. Retrieved from https://www.ifixit.com/Guide/Image/meta/v6P3IL65vPaNOV2O. Step 8: Detach motherboard Try not to endeavor to completely uproot the motherboard as it is still joined to the inside mid-frame by the Micro-USB port daughterboard connector. Lay the motherboard on a clean level surface and backing the inside mid-frame with one hand, leaving the other hand allowed to chip away at the motherboard as like in image. Figure 9 Lionheart, S. (n.d.). Samsung Galaxy S5 Battery Replacement. Retrieved from https://www.ifixit.com/Guide/Image/meta/vHqKh4ogPUhqFv4n. Step 9: Remove back camera with tweezers Use the flat end of a spudger to disconnect the backside camera connector straight up from its socket on the motherboard then remove the camera from the motherboard with a pair of tweezers. Figure 10 Lionheart, S. (n.d.). Samsung Galaxy S5 Battery Replacement. Retrieved from https://www.ifixit.com/Guide/Image/meta/vHqKh4ogPUhqFv4n. Step 10: Front facing camera Since, front facing camera and back facing camera have same identical connection follow the same steps for front camera. Figure 11 Lionheart, S. (n.d.). Samsung Galaxy S5 Battery Replacement. Retrieved from …show more content…
Understanding of this repair guide can be a powerful tool to fix the problems. This will productively help to oversee and control of e-waste. Refurbish is one of the important parts of proposal where elements can be recycled and reused which in turn leads to environmental safety. There are numerous security concerns related with the gadget and one needs to comprehend the issue and comparing arrangement. We anticipate that users will take all the precautionary steps and use all the safety equipment while using this repair guide like safety glasses, data sheet of devices. We believed that, you will like our proposal and will permit us to continue assist with the goal that we keep on enhancing all through the procedure to make it worth for utilization. Following section has some troubleshooting instructions. These basic instructions can be obeyed in case repair guide doesn’t
Step 4: Remove the plug by hand. Be prepared for the rush of hot oil!
Click the AP or the PDA button you can see from the Odin user-interface and browse the desktop for the S5 Mini CF-Root tool.
After that, literally kicking the kickstand which located at left side bottom part of the body cover.
For this cable I will use the Rj45 connector which is standard connection for most systems .I would then measure the cable I needed and trimmed it to the proper length using the cable cutter. Then I Used the cable stripper to strip about 1 ½ inch of the jacket from the end of the cable. Pull the trimmed jacket from the cable, there will be an exposed white thread cut that to the end of the strip cable so it will not be in the way of your connector. Untwist all the inner
You will have to turn the lug nuts counter clockwise to loosen them. Do not remove the lug nuts all the way off the threaded shaft. Next, to get the wheel off the car, you have to raise the corner of the car where the flat is located.
You will now want to turn the computer monitor on its side and remove the top of the casing so that you can clearly see the motherboard. You may be able to do this by hand, but it might require a screwdriver.
You must show that you have taken it apart enough to answer the questions. Please don’t copy more than a 2-3 pages of web material.
With your replacement cord set in hand, you can replace the cord with a few simple steps. Use scissors to cut the cord above the damaged area, making a clean cut. This end then fits into the part of the replacement cable called the wiring channel. Simply clamp the wire in, screw it shut, and a solid connection will be made with the replacement
The third piece was the easiest to remove and replace. It did not have a direct impact but it was still a possibility due to some interconnecting cables that could have been damaged.
Place your towel flat on your work surface before proceeding (this is to help prevent oil, grease, powder residue, and your firearm from damaging the work surface). The first step in disassembly after making the weapon clear and safe is to separate the upper receiver group from the lower receiver group. Locate the takedown pin, which is located just above the safety, and the pivot pin, which is located at the front of the lower receiver. With your number 2 punch depress the takedown pin from the left side. You should feel a noticeable click when the takedown pin overcomes the force of the takedown pin detent. Repeat for the pivot pin, being careful not to push the pin all the way through the receiver. The takedown pin and pivot pins should now be partially extended on the right side of the lower receiver. Lay the firearm on its left side so it lies flat on your work surface. Grasp the takedown pin from the right side and pull till it fully extends out the right side of the receiver. Again, you should feel a noticeable click when the detent pin engages the takedown pin at the fully extended position. Now repeat by grasping and pulling the pivot pin till it fully extends out the right side of the receiver. Next, while holding the lower receiver group, grasp the upper receiver group and slide it clear of the lower receiver group. At this point the lower receiver group disassembly is complete, so sit it to one side
So, you're gonna use that flat blade screw driver to start busting that away, then your gonna grab a dremel tool and just clean it up and do a little bit of reaming to make sure the new receptacle is gonna fit. So as we have it, uh, most of it chipped away, you can use a dye grinder; dremel tool until its [inaudible 00:02:11]]. Obviously we have a die grinder here just for speed reasons. That tool that he is using on the dye grinder there is called a burr you can pick it up at any industrial hardware
In the BIOS use the down arrow to scroll to "Integrated Devices (Legacy Select Options). Press Enter
1. Carefully remove the Motherboard, and place it on top of the anti-static bag it came in, and then place that on top of the box.
After you have tightly crewed those in you will want to take the PC board and set it on top of the mounting screws. You will want to place the holes of the PC board over the mounting screws. You will then want to screw down the PC board to the side panel. After you have done this place the side panel, with the PC board attached, back into the case and replace the screws that were holding it.
Connect the other end of the SATA cable to the proper connector on the motherboard. (Refer to the motherboard documentation for help.)