While discussing the fail-safe function: Technician A says that the 4WS indicator light is illuminated during the fail-safe function. Technician B says that the rear wheels steer normally when the 4WS control unit enters the fail-safe mode. Who is correct?

While discussing the fail-safe function: Technician A says that the 4WS indicator light is illuminated during the fail-safe function. Technician B says that the rear wheels steer normally when the 4WS control unit enters the fail-safe mode. Who is correct?

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter44: Four- And All-wheel Drive

Section: Chapter Questions

Problem 7ASRQ: While diagnosing the cause of the transfer case jumping out of gear: Technician A says that the most...

See similar textbooks

Related questions

Q: Describe the 4 distinct modes the vehicle should be operated in during a road test when diagnosing…

A: Four distinct modes the vehicle should be operated in during a road test when diagnosing final…

Q: The main job of the idler arm is to __.a. support the left side of the center linkb. support the…

A: The idler arm is designed to keep the center link parallel to the road surface while allowing the…

Q: Technician A says that a malfunction of the ABS causes the control module to shut off or inhibit the…

A: The system will be shut down if any malfunction is monitored in the ABS because the control module…

Q: causes for damage to the surface of a pressure plate. Technician A says a worn clutch disc can score…

A: Pressure plate is an important part of vehicles clutch system. It applies pressure to clutch disc to…

Q: When checking the fifth wheel, coupling device, the Certified Inspector must check the condition and…

A: Answer = True

Q: What three functions are performed by the clutch safety switch when the car has an electronic engine…

Q: Define the difference between an integrated and anonintegrated antilock braking system.

A: ABS braking system is used to stop the automobile at the desired position with in the specified…

Q: 2. Technician A says that load-carrying ball joints should always have some play in them. Techni-…

A: The ball joints basically serve as the pivot point between the tyre and the suspension in an…

Q: Dicuss the power train of four wheel tractor.

Q: 2. Technician A says that the purpose of the steering wheel holder is to make sure that the steering…

A: In this problem, Technician A is talking about the purpose of a steering wheel holder. He is telling…

Q: if you read the scan codes on the vehicle and U0121 was standa for lost communication with antilock…

A: Solution::: == The U0121 code stand for Data bus: anti-lock brake system (ABS) control module - no…

Q: Technician A says that some shift solenoids can be activated by providing a ground for the solenoid.…

A: The shift solenoid is used in the gear assembly which shifts the gear according to the desire of…

Q: Technician A says that a malfunction of the ABS causes the control module to shut off or inhibit the…

A: Automobile

Q: While discussing the various types of transmissions found on today’s vehicles: Technician A says…

A: Sliding collar transmission-In sliding collar transmission we must move a fork which engage or…

Q: Technician A says hydraulic pressure affects transmission shift points. Technician B says hydraulic…

A: Affects of hydraulic Pressure : When hydraulic fluid enters into the bore of the cylinder it forces…

Q: Which of the following is part of the sprung weight ofa vehicle?a. Steering linkageb. Tiresc.…

A: A vehicle’s sprung weight is supported by springs of one kind of or another (coiled springs, air…

Q: Technician A says that throttle position is an important input in most electronic shift control…

A: In electronically controlled automatic transmission, the most appropriate gear ratio for the power…

Q: An indirect TPMS is being discussed. Technician A says that if a specific tire is low, the system…

A: Indirect TPMS works along with your car's Antilock Braking System's (ABS) wheel speed sensors. If…

Q: Technician A says that broken or worn engine and transaxle mounts can cause a transaxie to have…

A: Given Transaxle problem To find Statement with is/are correct Shifting problem of transaxle can be…

Q: While discussing throttle-by-wire systems: Technician A says that a spring on the throttle shaft…

A: Given that Technician A says that a spring on the throttle shaft provides the limp-home feature.…

Q: clutch is fully engaged, the driven disc does not rotate at the same speed as the driving members *

A: Slipping occurs when the clutch is fully engaged and the driven disc does not rotate at the same…

Q: . Technician A says that leaf spring-type rear sus- pensions are subject to axle tramp. Technician B…

A: We are authorized to answer one question at a time since you have mentioned question 4 only so we…

Q: Technician A says that limited- slip differential clutch packs are designed to slip when the vehicle…

A: Limited-slip differential clutch packs is a modification to the regular differential mechanism. LSD…

Q: 108) Technician A says that engine management malfunctions may be misinterpreted as transmission…

A: Engine management malfunctions can be seen by malfunction indicator lamp . this indicator shows that…

Q: What is the primary difference between an automatic traction control system and a stability control…

A: Traction control system in an automobile is designed to prevent the driving wheel from loosing the…

Q: Describe the normal pedal feel when the ABS is activated during hard braking?

A: Anti braking system(ABS): Anti braking system(ABS) allows a driver to apply the brakes quickly…

Q: Technician A says that electronically controlled power-steering systems allow for power assistance…

Q: 104) Which of the following inputs is NOT a driver commanded input? Brake pedal switch Mass airflow…

A: Given Driver commanded input To find Verify from the following which is not driver commanded input

Q: Technician A says that negative caster provides directional stability . Technician B says that pos…

A: Caster refers to the angle of the steering axis on a vehicle wheel from the straight line of the…

Q: a. Define the following term 1. Lateral vehicle dynamics 2. oversteers 3. steering wheel shimmy…

A: Lateral Vehicle dynamics This is the study of vehicle dynamics that cause the lateral motion or…

Q: While discussing transmission adaptive learning: Technician A says that the transmission learns to…

A: Transmission Adaptive learning:-The automatic transmission is designed in such a way that it has a…

Q: Explain the different topic that is given. 1. what is the bleeding clutch hydraulic system 2. What…

A: Please find the solution for the first part of the question below. Also, please note that as per…

Q: Unequal SAI angles on the left and right sides of thefront suspension may cause __ .a. tread wear on…

A: All the suspension system involves springs and dampers. As the vehicle travels down the road, all…

Q: 4 Wheel Steering(4WS) While discussing the fail-safe function: Technician A says that the 4WS…

A: Technician A is correct.

Q: A self-adjuster screw mechanism (star wheel) can be positioned on either the left or the right side…

A: The self adjuster screw mechanism is used in automobile braking systems. A self adjuster screw…

Q: While discussing steering problems: Technician A says that a “jerky” steering wheel and a “clunking”…

A: Technician A is correct.

Q: 35. Technician A says positive caster will result from excessive toe-in. Technician B says a vehicle…

A: caster angle, camber angle, and toe or toe-out are the angles that are used to apply in the vehicle…

Q: List at least five separate checks that should be made during the visual inspection of the…

A: Checks need to be done during the visual inspection of the transmission/transaxle are:

Q: Technician A says a sticking inboard joint can cause the car to shimmy during acceleration.…

A: Solution:

Q: If an actuator fails to move, name five possible causes.f an actuator has slow or erratic motion,…

A: Actuator is a component of a machine which capable in moving in a controlled mechanism.It consist of…

Q: Tech A says that the purpose of a steering wheel holder is to make sure that the steering wheel is…

A: In this problem, Tech A is talking about the purpose of a steering wheel holder. He is telling that…

Q: A hot-wire MAF has low resistance across it when the wire is hot: Technician A says that this…

A: In a fuel injected internal combustion system the mass flow rate of air is determined by a sensor,…

Q: List five things that could cause incorrect shift times and poor shifting quality

Q: Technician A says that play in the steering gear is the probable cause of a shimmy. Technician B…

A: please rate me positive Data given- Statement of Technician A- play in the steering gear is the…

Q: When replacing an accessory drive belt, all the following are important considerations EXCEPT:…

A: Correct Option: d. Belt routing.

Q: Which one of the following is not regulating the mean speed of an engine, when there are variations…

Q: List at least three causes of noise that are not transmission related but may appear to be

A: In the transmission systems, noise is one of the biggest concern. Noise is used to identify the…

Q: used to change of the power force steering to liners movement *

A: Box steering Rear wheel

Q: Technician A says that the throttle position is an input to the PCM. Technician B says that the…

A: When brake pedal switch is pressed it sends an input to the PCM to maintain idle speed of a…

Concept explainers

General safety guidelines

Safety guidelines are the set of rules and codes that must be followed in the workplace for the occupational safety of workers, the machines, and the equipment that are present inside the workshop premise. There are many unsafe conditions and hazardous materials inside the workshop that makes prey for certain risk factors associated with health conditions. Extreme safety precautions must be taken inside the work area just like the precautions and practices that are been followed for Corona Virus Disease 2019 (COVID-19). People can also educate themselves by joining various health programs and camps. These will provide them with the necessary skills and knowledge about safety awareness. Occupational Safety and Health Administration (OSHA) thrives to create a safe and healthy environment for the workers working in the industries and provides them with proper education and training.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

4 Wheel Steering(4WS) While discussing the fail-safe function: Technician A says that the 4WS indicator light is illuminated during the fail-safe function. Technician B says that the rear wheels steer normally when the 4WS control unit enters the fail-safe mode. Who is correct?
Technician A says that a malfunction of the ABS causes the control module to shut off or inhibit the system. Technician B says that a loss of hydraulic fluid or power booster pressure disables the antilock brake system. Who is correct?a. Technician A only.Technician B only.Both A and B.Neither A nor B
When checking the front end, which of the following are NOT cause for rejection? Bearing cap is broken or missing or if there are any cracks or welded repairs to any components. Front axle is bent or gear box mounting is loose, bolts are missing, or bolts or case are cracked. All of the statements shown are cause for rejection. The steering damper leaks, is loose, mount is cracked/ broken, or is missing or steering shaft coupler/universal is binding, frayed, or cracked.
Technician A says that a malfunction of the ABS causes the control module to shut off or inhibit the system. Technician B says that a loss of hydraulic fluid or power booster pressure disables the antilock brake system. Who is correct? a. Technician A only b.Technician B only c.Both A and B d.Neither A nor B
when discussing shift problems, technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems. technician b says that poor shift boot alignment can cause a transaxle to jump out of gear
Technician A says that the throttle position is an input to the PCM. Technician B says that the brake pedal switch is an input to the PCM. Which technician is correct
While diagnosing the cause of TCC shudder: Technician A checks the fluid pressure sent to the clutch. Technician B says that because the shudder occurs only after the clutch is engaged, the problem is the engine, transmission, or another component of the driveline. Who is correct?
Technician A says that if a drive belt does not have the proper tension, it may produce squealing and chirping noises. Technician B says belt tension should be checked even if the engine has an automatic belt tensioner. Who is correct? Technician A Technician B Both A and B Neither A nor B
Technician A says that some systems use a special modulated shift control solenoid. Technician B says that some systems use a special modulated converter clutch control solenoid. Who is correct? Technician A says that shift solenoids direct fluid flow to and away from the apply devices in the transmission. Technician B says that shift solenoids are used to mechanically apply a friction brake or multiple-disc clutch assembly. Who is correct? Technician A says that throttle position is an important input in most electronic shift control systems. Technician B says that vehicle speed is an important input for most electronic shift control systems. Who is correct? Technician A says that a faulty TP sensor can cause delayed shifts. Technician B says that delayed shifts can be caused by an open shift solenoid. Who is correct? Technician A says that some shift solenoids can be activated by providing a ground for the solenoid. Technician B says that some shift solenoids can be activated by…
Technician A says the front wheel bearings on a typical FWD car are sealed and non-adjustable. Technician B says the front wheel bearings on a typical FWD car are greaseable and adjustable. Who is correct?
A hot-wire MAF has low resistance across it when the wire is hot: Technician A says that this condition will cause the engine to stall as soon as you put the transmission into gear. Technician B says that this condition will cause the transmission to shift late. Who is correct?
Which of the following would NOT be cause for rejection when checking the power steering system? System does not work or any hoses are chafed. Any visible leaks (lines, hoses, steering box, rack and pinion, & hydro-boost if equipped). Power steering belt(s) are missing, loose, frayed, or bind or contact other objects. A clamp holding down a power steering line or hose is missing.