Waterflowsthrougha pipe at150L/schangesgradually in diameter from 165 mm at point M to 473 mmTheandthatм isrespective pressurespointm higherpointatN.4.3thanN.at point M and N are72 kPa49.8 kPa.a. Determine the head lost of the pipe.b. Determine the total energy at point N with datum atpoint M.c. Determine the total energy at point M with datum atpoint M.

Answered: Image /qna-images/answer/be0711d3-8fcb-44e4-98dc-25cef517e869.jpg

through a pipe at 150 gradually in diameter from 165 mm at point M to 473 mm Water flows L/s that changes at point N. M is 4.3 m respective pressures at point M and N 49.8 kPa. higher than point N. The and 72 kPa a. Determine the head lost of the pipe. b. Determine the total energy at point N with datum at point M. Determine the total energy at point M with datum at point M.

through a pipe at 150 gradually in diameter from 165 mm at point M to 473 mm Water flows L/s that changes at point N. M is 4.3 m respective pressures at point M and N 49.8 kPa. higher than point N. The and 72 kPa a. Determine the head lost of the pipe. b. Determine the total energy at point N with datum at point M. Determine the total energy at point M with datum at point M.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

OIL WITH SP.GR. 0.95 FLOWS AT 200 ? ??/??? THROUGHA 500 METER OF 200 MM DIAMETER PIPE (? =0.0225).DETERMINE THE HEAD LOSS A. 121.16 ?????? B.106.21 ??????C. 116.20 ?????? D.161.20 ?????
- Dekrmine the total head loss hf. from Å to o in the systen shomwn in the figure iF the discharge is 1. G0 mls. Assume f=0:02 for all pipes 450 mm o, GO0 m 9oomm ở , 90 m 구5Dmmd,40m D GUD mm,720m
IV K/s classwork.pdf -> a A jet af wouter From a 25 mm dinmeter nozzle is directed vertieully upuards. Assumning that the jet remains circular and neglecting any less ef enargg that will be the dinmeAer at a point 4.5 m above the ne tzle, if the velecity with which the jet leaves the nozzle is 12 m/s? A jet ef water 4.5M nozale
Q4: Assuming f-0.020, determine the discharge in the pipes. Neglect minor losses. Pipe Diameter AB 250 mm 200 mm 400 mm BC BD Length 1200 m 600 m 200 m EL.45m EL 3m. B C EL. 3.0m D EL 0.0m
Ex 18: For. the. Cofferdam Shown.in the. Eig. below.; find: O The Capacity of the Pumprefuired.. ®. Pore Water Pressure at Points. A, B, C. O Factor of. Sahty against. PiPing.. @ What height of Water. outside the Cafferdam Would. give E.S -2. 25 Esat:= 18 -KN /m 士 -C- %3D -5 K= 2.6 x 1o. m/sec 4m 2.25m Datum
Q1) Find The magnitude and direction of The Rorce exerted on The Blade shown bulowby aget, iE The slope angle (0= 120),The velocity V=Vz= 30m/sec, and The discharge (loLIsec)? Blade des Fx Fy
Fox flowe rate 28 Lis Find pump Power EL. 60M L00 Mm. 150 Mm El. 30M
Situation 1: A pump draws water from reservoir A and lifts it to reservoir B as shown. The head loss from A to 1 is three times the velocity head in the 150-mm diameter pipe and the head loss from 2 to B is twenty-five times the velocity head in the 100-mm diameter pipe. The discharge in the pipe is 20 liters/second. EI. 240m B El. Om 100mm A O 150mm El. -20m 2. Find the power delivered by the pump in kW. 3. Calculate the pressure head at point 1 in meters. 4. Solve the pressure head at point 2 in meters.
Elev. 110' Inv. 102.5 Elev. 127.6 623.5 -1000' 2000' B Inv. 85' Assuming the conduit in the figure is a 36" wrought iron pipe flowing full, and that the outlet is at point B: a) Calculate the head loss in the flow by the time it reaches point B. b) Calculate the velocity and flow at point B, in the pipe considering friction. c) Sketch the EGL and HGL of the conduit.
By comparing the result between Slope Deflection Equation and Modified Moment Distribution Method, determine end moment for all member and reaction at the support and then draw SFD and BMD for each beam.
Problem 7 - 66 Determine the flow in each of the pipes shown in the figure. Assume f 0.02 for all pipes. El. 90 m El. 75 m B El. 50 m El, 30 m D. Line 3: 45um - 300mm Line 4: 900m - 150mm Line 1: 600m - 600mm Line 2: 300m - 200mm C.
أنت الآن Q-2 Water flows through a vertical contraction (venturi) section. Piezometers are attached to the upstream pipe and minimum area section as shown. The velocity in the pipe is 3 mis. The difference in elevation between the two water levels in the piezometers is 15 cm. What is the velocity at the minimum 15 cm area? 3 mis II