The two wheels of the vehicle are connected by a 19-kg link AB with center of mass at G. The link is pinned to the wheel at B, and the pin at A fits into a smooth horizontal slot in the link. If the vehicle has a constant speed of 4.8 m/s, determine the magnitude of the force supported by the pin at B for the position 0 = 33° 0.6 m 0.4 mA Answer: B = i 0.97 m G BY 0.79 m 0.4 m 0.6 m N

The two wheels of the vehicle are connected by a 19-kg link AB with center of mass at G. The link is pinned to the wheel at B, and the pin at A fits into a smooth horizontal slot in the link. If the vehicle has a constant speed of 4.8 m/s, determine the magnitude of the force supported by the pin at B for the position 0 = 33° 0.6 m 0.4 mA Answer: B = i 0.97 m G BY 0.79 m 0.4 m 0.6 m N

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.11P: Solve Prob. 7.10 assuming that the pick-up truck has front-wheel drive.

See similar textbooks

Similar questions

The crank OA rotates in the vertical plane with a constant clockwise angular velocity Wo of 2.3 rad/s. For the position where OA is horizontal, calculate the force under the light roller B of the 17.4-kg slender bar AB. 0.30 m 000 -7 0.65 m B 0.86 m = Answer: FB i N
The position of the small 0.68-kg blocks in the smooth radial slots in the disk which rotates about a vertical axis at O is used to activate a speed-control mechanism. If each block moves from r = 162 mm to r = 200 mm while the speed of the disk changes slowly from 272 rev/min to 382 rev/min, design the spring by calculating the spring constant k of each spring. The springs are attached to the inner ends of the slots and to the blocks.
A 15-kg uniform disk is placed in contact with the ground and a constant couple moment M = 32 N.m is applied to it as shown. The weight of link AB is negligible. If the coefficient of kinetic friction at D is 0.3, find the angular acceleration of the disk. write the answer in rad/s? but do not write the units. R = 0.25 m A Taylor Answer:
Go 0.3 m---0.2 m- 0.2 m 0.4 m 60° 0.5 m The hand truck has a mass of 198 kg and a center of mass at G. Determine the maximum magnitude of the force P (in kN) that can be applied to the crank so that wheels A or B remain in contact with the ground. . Neglect the mass of the wheels.
The crank AB rotates in the vertical plane with a constant clockwise angular velocity w0 . For the position shown calculate the force under the light roller C of the 10-kg slender bar BC w0=4.2 rad/s. Solve correctly please.
The smooth surface of the vertical cam is defined in part by the curver - (0.2 cos 0+ 0.3) m. (Figure 1) Figure If the forked rod is rotating with a constant angular velocity of 4 rad/s, determine the force the cam and the rod exert on the 1.1-kg roller when 0-30°. The attached spring has a stiffnesss k- 30 N/m and an unstretched length of 0.1 m. Express your answers in newtons using three significant figures separated by a comma. Neam, Frod = Submit AΣo↓ vec Previous Answers Request Answer * Incorrect; Try Again; 3 attempts remaining < Return to Assignment Provide Feedback Kwi| ? N
The motorcycle in the figure has a mass of m1 kg and its center of mass is at G1. The mass of the driver is m2 kg and the center of mass is at G2. Since there is fs between the wheels and the asphalt, determine whether it is possible for the driver to lift the front wheel off the ground. Neglect the mass of the wheels and assume that the front wheel can spin freely. a=0.41 m b= 0.39 m c= 0.75 m d= 0.25 m e=0.58 m m1=120 kg m2= 77 kg fs=0.82
The frame is made from uniform rod which has a mass p per unit length. A smooth recessed slot constrains the small rollers at A and B to travel horizontally. Force P is applied to the frame through a cable attached to an adjustable collar C. Determine the magnitudes and directions of the normal forces which act on the rollers if (a) h = 0.25L, (b) h = 0.50L, and (c) h = 0.81L. The forces will be positive if up, negative if down. Evaluate your results for p = 2.5 kg/m, L = 510 mm, and P = 43 N. What is the acceleration of the frame in each case? Answers: (a) (b) L (c) h= 0.25L: h = 0.50L: h = 0.81L: L A A A = B i i i h P N. N. N₁ B i i i N. N. N. i i i m/s m/s m/s
The flat band that goes from pulley A to pulley B has a coefficient of static friction us=0.4, it prevents the motor and its supporting weight of W=240 lb from falling. Determine the moment that the belt transmits to pulley B knowing that pulley A rotates clockwise. 6 in A 10 in C W -12 in- B
Your answer is partially correct. The figure shows the cross section of a uniform 174-lb ventilator door hinged about its upper horizontal edge at O. The door is controlled by the spring-loaded cable which passes over the small pulley at A. The spring has a stiffness of 12.7 lb per foot of stretch and is undeformed when = 0. If the door is released from rest in the horizontal position, determine the maximum angular velocity reached by the door and the corresponding angle 0. Answer: Wmax = www 4.2' 0.636 rad/sec at 0 = 58.49 O
At time t = 0, the operator of the road roller disengages the transmission so that the vehicle rolls down the incline as shown in the figure. Determine an expression for the vehicle’s speed as a function of time. The two rear wheels weigh 300 lb each and have a radius of 5 ft. The front wheel weighs 950 lb and has a radius of 3 ft. The vehicle body weighs 600 lb. Assume the wheels roll without slipping. The expression for the speed of the road roller as a function of time is given by v· = agsin(θ)v· = agsinθ .The value of a is determined to be:
The figure shows the cross section of a garage door which is a uniform rectangular panel 7.3 ft by 7.3 ft and weighing 236 lb. The door carries two spring assemblies, one on each side of the door, like the one shown. Each spring has a stiffness of 71 lb/ft and is unstretched when the door is in the open position shown. If the door is released from rest in this position, calculate the velocity of the edge at A as it strikes the garage floor. omwmwwww B 7.3' 9.2' 7.3' Answer: VA = i ft/sec