The three-station work cell at Pullman Mfg., Inc. is illustrated in the figure below. It has two machines at station 1 in parallel (e, the product needs to go throu proceeding to station 2). 30 min/unit Station 11 Machine A is the bottleneck station. Station 1 Machine B 30 min/unit Station 2 5 min/unit a) The throughput time is minutes (enter your response as a whole number). b) The bottleneck time of this work cell is minutes per unit (enter your response as a whole number). Station 3 6 min/unit C ) If the firm operates 8 hours per day, 6 days per week, the weekly capacity of this work cell is units (enter your response as a whole number).

The three-station work cell at Pullman Mfg., Inc. is illustrated in the figure below. It has two machines at station 1 in parallel (e, the product needs to go throu proceeding to station 2). 30 min/unit Station 11 Machine A is the bottleneck station. Station 1 Machine B 30 min/unit Station 2 5 min/unit a) The throughput time is minutes (enter your response as a whole number). b) The bottleneck time of this work cell is minutes per unit (enter your response as a whole number). Station 3 6 min/unit C ) If the firm operates 8 hours per day, 6 days per week, the weekly capacity of this work cell is units (enter your response as a whole number).

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

A 16 x 1 MUX is implemented using 4 x 1 MUX. Assume at level 1 and level 2 of circuit X and Y number of MUX required respectively. Then value of (X-Y) is... Correct answer will be upvoted, else downvoted.
The unique addresses assigned to the four registers (R11,R12,13,R14) of the I/O interface are equal to the XX3 , XX7 , XXB and XXF in Hex . Where XX is hex digits equal to your roll no . (if student is having roll no 45 than address are 453 ,457 ,45B , 45F in Hex ) .Show the well labeled external circuit that must be connected between and 12-bit I/O address from the CPU and the CS, RSI, and RS0 Inputs of the Interface.
Using Logism for otherwise complete the attached 8 bit alu The Arithmetic Logic Unit The most important and possible most difficult component to implement is the arithmetic logic unit. Thefunctions of the ALU are shown in Table 1. The ALU should have 5 inputs (A-input, B-input, F0-input, F1-input, Finput) and 1 output (C-output). You will need to determine how many bits each input and output should have.Remember, you are designing an 8-bit microprocessor! . For example, to add the value on the A-bus8-bit ALUto the value on the B-bus, you can simply use an 8-bit adder. Explore the components in Logisim! Additionally,you can think about using a multiplexer to determine which ALU function will be performed
Consider a special purpose decoder that is called BCD to seven-segment decoder. The decoder takes a 4-bit Binary Coded Decimal (BCD) number X3 X2 X4 X0 (0-9) and produces 7 outputs a, b, c, d, e, f, and g The specification of this circuit is as follows: ⚫ The 7 outputs of the decoder are connected to LED segments as shown in the figure below. The LEDs are active low, ie, the LED emits light when it is connected to logic 0. • The decoder output is determined in a way so that the LED segments display the decimal representation of the input. For example, if the input X3 X2 X1 X0 is 0001 respectively (which is equivalent to decimal 1), the outputs a, b, c, d, e, f, and gare 1001111 showing the letter 1 on the display (remember the LEDs are active low). Decoder W- 4x7 e U Answer the following questions: a. Fill in the truth table of that decoder. Choose a good value for the output when the input is greater than decimal 9. b. Derive the simplified Boolean expressions for the outputs a, b, c,…
Let X be number of gates in an 8-bit adder (i.e., adds two 8-bit numbers) and Y be the number of gates in a 16-bit adder (adds two 16-bit numbers). Which of the following is true of X and Y? A. Y is smaller than X B. Y is about the same as X C. Y is a larger than X, but not twice as large D. Y is about twice as large as X E. Y is much more than twice as large as X
A counter circuit is shown in the figure. The counter counts as Q1 QO Vpp J Q Q Clock K K O a. QOQ1: 11 --> 00 --> 10 --> 01 --> 11 O b. QOQ1:00 --> 01 --> 10 -->11 --> 00 O c. QOQ1: none of these O d. QOQ1: 11 --> 01 --> 10 --> 00 --> 11 Cl
· A Full Adder accepts two input bits and an input carry and generates a sum and carry at its output side (refer to Table 1). Two or more full adders can be connected in parallel to perform binary addition operation for more than 2 bits. The input bits and input carry are denoted as A, B and Cin respectively. Construct a finite state machine that represents the addition. Table 1 A В Cin Sum Carry 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
In this link: https://edaplayground.com/ , Provide VHDL codes using Dataflow Modeling with the given problem below. PROBLEM: In a simple copy machine, a stop signal, S, is to be generated to stop the machine operation and energize an indicator light whenever either of the following conditions exists: (A) there is no paper in the paper feeder tray; (B) the two microswitches in the paper path are activated, indicating a jam in the paper path. The presence of paper in the feeder tray is indicated by a HIGH at logic signal P. Each of the microswitches produces a logic signal (Q and R) that goes HIGH whenever paper is passing over the switch to activate it.
The connection diagram shows multiple gates and the pins assigned to each gate. For example, from the datasheet connection diagram of IC 7400, four individual NAND gates can be observed. Pins 1, 2 and 3 are all related to one of the four NAND gates. For each gate the top input is assigned the letter A while the bottom input is assigned B and the output is assigned the letter Y. The function tables of the ICs are normally given in terms of H (High logic level) and L (Low logic level). Referring to the datasheet function table of IC 7400 shows the four different input combinations of A and B and the corresponding output Y for one of the four NAND gates. There is also one more letter assignment that could be found in function tables, this is the letter X, a don't care assignment. In cases where an X is given, it can be replaced by either an H or L assignment without effecting the resultant functionality of the IC. An example of this case can be seen for the function table of IC 7402. The…
QUESTION 5 35 A convolutional circuit has three internal registers (s0, s1, and s2), and two outputs (c0 and c1), calculated as follows: c0=i+s2; c1=i+s0+s1. We are currently in state 110 and receive input 0. What is the output and next state? O c0=0; c1=0; next=011 O c0=1; c1=0; next=011 O c0=1; c1=1; next=011 O c0=0; c1=1; next=011 QUESTION 6 11 A convolutional circuit has three internal registers (S0, S1, and s2), and two outputs (c0 and c1), calculated as follows: c0=i+s0; c1=i+s1+s2. We are currently in state 110 and receive input 0. What is the output and next state? O c0=1; c1=1; next=011 O c0=0; c1=1; next=011 O c0=0; c1=0; next=011 O c0=1; c1=0; next=011 QUESTION 7 02 A convolutional circuit has three internal registers (s0, s1, and s2), and two outputs (c0 and c1), calculated as follows: c0=i+s0; c1=i+s0+s1. We are currently in state 011 and receive input 1. What is the output and next state? O c0=0; c1=1; next=101 O c0=0; c1=0; next=101 O c0=1; c1=0; next=101 O c0=1; c1=1;…
Present Next state Output z state W2 W1 = 00 01 10 11 00 01 10 11 A A B D (A 1 1 В C B B D 1 0 0 C C B A 1 0 1 A C D) D) D 1 - Figure 1: Flow Table Question IIa Part b The flow table of shown in Table 1 is for an asynchronous sequential circuit. For this table, determine a state assignment involving a minimum number of variables which allows for a race-free implementation. Then build the corre- sponding table of excitement. Assign the outputs when needed such asit has at most a simple change of output during the time where the network is unstable. It is assumed that the inputs rı and x2 never change at the same time. Finally, obtain the expressions of minimum cost for the realization of the circuit using S-R type latches.
Computer Science if a 12-bit linear pcm code with a resolution of 0.188V, if the voltage range that would be converted to the pcm code: 111110111101 is in the form X volts to Y volts where X and Y are constants. Find X+Y