The required 7-segmrnt decoder should have 3-inputs (which are the bits of the binary number desired tobe designed, call them A,B,C), and 7 outputs (the 7 segments of the display unit which are a, b, c, d, e, f& g).8.gf a bt la Obd Dpe d8c DpThe 7-segment to be used is of common anode type. Consequently, any segment will be ON if its inputis Low, meaning that for displaying 0 the segments inputs (a,b,c,d,e,f.g) should be (0000001), or g will beOFF while all the others are ON.1- Make a table explaining the inputs and the corresponding outputs for the 6 combinations input(000.101), assuming the other two combinations as don't care.2-Find the output as a function of the inputs (A,B,C) using K-map to minimize the expressions3-Show your design using 2-input, and 3-input NAND gates, and inverter.

We need to design 7 segment decoder circuit using 3 inputs A,B,C. We need to find output as a…

The required 7-segmrnt decoder should have 3-inputs (which are the bits of the binary number desired to be designed, call them A,B,C), and 7 outputs (the 7 segments of the display unit which are a, b, c, d, e, f & g). d Dp TT e d8c Dp COM -

The required 7-segmrnt decoder should have 3-inputs (which are the bits of the binary number desired to be designed, call them A,B,C), and 7 outputs (the 7 segments of the display unit which are a, b, c, d, e, f & g). d Dp TT e d8c Dp COM -

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Q27. a) What do you mean by PD controller ?.Draw the electronic circuit of PD controller and also…

A: a)

Q: 1. The bit sequence 1101 is serially entered (right-most bit first) into a 4-bit parallel out shift…

A: [1] Consider a four bit shift register Q3 Q2 Q1 Q0 Given, Initially the register is clear, Q3 =0, Q2…

Q: How many bits are required for the control selector in the 64x1 multiplexer? a. 4 O b. 5 О с. 6 How…

A: Use fundamental of multiplexer design 1)Option c 6 2)Option c 8

Q: Given a machine with a 30-bit word address, how would you delineate fields in this 32-bit address…

Q: b) What is the purpose (jll ) of the parity bit during data transmission?

A: According to the question we have to discuss the purpose of the parity bit during the data…

Q: 2. How can a serial in/parallel out register be used as a serial in/serial out register?

Q: Logic diagram using a single 3x8 decoder FOR y=(A'+B'+C)'

Q: Q- Design using BCD 7 Segment Decoder, the following mathematical set characters if you entered 3,…

A: For Led of that segment to ON we give 1 or +5 volt and for off 0 or ground. Taking all cathode…

Q: After execution the short label jump instruction: JMP 84h; (when updated IP =A4h), the new value of…

A: JMP instruction is a short jump instruction. It is used to jump within the range of +127 to -128.

Q: What is the function of the odd parity generator circuit? O a. produces an output of '1' for even…

A: As per Bartleby guidelines we are allowed to solve only one question, since these parts are…

Q: A code 1011 need to be send to the receiver. Using, Hamming code find out the code-word and the…

A: hamming code is a error correcting code. it can detect an error and correct it. the position of…

Q: X1,X2,X3, and X4 are four variables. X1's range is (0 to 200), X2's range is (0 to 24h), that of X3…

A: The explanation is as follows.

Q: What is meant by 4 to 16-line decoder? Draw the block diagram of that decoder (Please don't show the…

A: As per bartleby guidelines we are supposed to answer only question as it is not a subpart, So I have…

Q: In a microcontroller program, a subroutine starts at address 016F and ends with a 'return'…

A: Below find the solution !!

Q: 8- What is the weight of the MSB of a 5-Bit number?-------

A: We are authorized to one answer at a time since you have not mentioned which question you are…

Q: 1-Why do we use DPSK? For the following message 1111000101110 give the DPSK system. (Note the…

A: DPSK

Q: What is the purpose of the Mux in a 1-bit Register?

A: Purpose of the Mux in a 1-bit register

Q: On the same fashion, describe the path followed by the value of INTERNAL SIGNAL towards P0.x (see…

A: Port 0 can be used as an input/output or a bidirectional data bus and lower order address for…

Q: For the switching function F = A (Ã + B), draw a corresponding set of logic blocks and write the…

A: We have been given a switching function and we have been asked to draw logic block diagram for this…

Q: using the multiplexer design approach should bé 8- Assuming that a certain ASM chart has 5 states,…

Q: Design a micro programmed system that adds two 16-bit numbers stored in the register pair AB and CD…

Q: Show the status of PSW (Program status word) after addition of two 8bit numbers 26H and 3FH. Also…

A: As per Bartleby guidelines we are allowed to solve only one question, please ask the rest again. The…

Q: What hex address will be decoded by the instruction OUT 6D, AL?

A: AL is the lower 8 bits OUT : Which output data from accumulator with 8 bit addresses Here the…

Q: Explain in a few sentences how a 4-bit binary ripple counter works.

A: Let us assume Q3 be the MSB bit and Q0 be LSB bit. And the output is Q3Q2Q1Q0

Q: Q1. Design a circuit of General register organization in which 4 registers are there from R0 to R3.…

Q: Draw the decoder that generates a logic "1" for each of the input shown below

A: A decoder is a digital circuit which detects the presence of a specified combination of bits on…

Q: DISCUSSION: 1- Is the Gray code arithmetic code? Why? Where this code used? 2- What is the parity…

A: Need to find about gray codes and parity bit Note:- as per our guideline we are supposed to answer…

Q: 2 (a) Determine the control word ICW2 require for PIC controller so that IRQ0 to IRQ7 correspond…

A: PIC is Programmable interrupt controller This helps a microprocessor to handle interrupt requests…

Q: Paragraph Styles Use a 2-bit counter X1 Xo with INC (increment) and CLR (clearance) logic to form a…

Q: . Design a 16 - to - 1 multiplexer using 4- to-1 multiplexer.

Q: In cases where the value of the four-bit N number consisting of W, X, Y, Z variables is N 10, the…

Q: If Timer 0 Register TMR0L is initialized with -1 in 8-bit mode, then after how many clock cycles…

A: Timer 0 has two register 1) TMR0L= Timer 0 Low 2) TMR0H= Timer 0 High after starting timer…

Q: Q3:(a)Draw the seven-segm ent di splay and write the BCD-to--seven segment decoder truth table

Q: The processor has performed the following addition operation: 0x01A0 + 0xC410 ------ 0xC5B0 What…

A: The signed 16-bit number in decimal can have either positive or negative sign. Let us consider for…

Q: In a DPCM system, the number of bits per sample is 7. How many levels are present in the quantizer?

A: A quantizer is an integral part of a differential pulse code modulated (DPCM) system. The number of…

Q: SV What is clocking block ? what is program block?

A: Reg is driven by always block it can't be driven by continuous assignment statement. Always block…

Q: Frame the command words ICW1, ICW2, ICW3 and OCW1 for initializing a single 8259to initiate INT 40H…

A: ICW 1 Whenever a command is issued with A0 = 0 and D4= 1, it is interpreted as ICW 1. 0 A7 A6 A5…

Q: Question 2: The HCS12 registers have the values shown in the attached table. Where X, means the…

A: A. What is the HCS12 operational mode? Given Mode Register contains the value 80 i.e MODE = $80 MODE…

Q: A- Answer (1) or (2) 1. For a digital signal (101100111001100010) use DPSK to transmit and receive…

A: Solution 1- The given digital signal is (101100111001100010). In the DPSK transmitter, the given…

Q: 1. Assume that the registers are 8-bit wide. Consider the following code: MOV R1, #4A MOV R2, #40…

Q: 1- Determine the logic required to decode the binary number 1011, by producing a HIGH indication on…

A: The given binary number is 10112 It is a 4-bit binary number. Let the input is A3A2A1A0. If A3=1,…

Q: Construct 3 to 8 and 6 to 16 Decoder with basic gates (Module KL-33005, block c). Truth Table…

A: As per guidelines we can solve only one question out of multiple question and 3 subparts Answer 3…

Q: 1. Write the TTL level of the following voltages (low, high, intermediate). 2.5. 0.3. 4.6.. 1.1 .…

A: Given the voltage levels TTL level for the above voltages are

Q: Write shift routines (LSL, LSR, ASR) that allow you to arithmetically shift 64-bit values that are…

A: Shift routines are written as shown below

Q: i): Implement the Boolean function ? = ??̅? using 2-input NAND gates in optimized manner. ii):…

Q: Draw the logic diagram of a fiveObit register with five D flipOflops and five 4 x 1 multiplexers…

Q: 10. Perform five bit (including sign), two's complement binary addition of the following decimal…

Question

The required 7-segmrnt decoder should have 3-inputs (which are the bits of the binary number desired to
be designed, call them A,B,C), and 7 outputs (the 7 segments of the display unit which are a, b, c, d, e, f
& g).
8.
gf a b
t la Ob
d Dp
e d8c Dp
The 7-segment to be used is of common anode type. Consequently, any segment will be ON if its input
is Low, meaning that for displaying 0 the segments inputs (a,b,c,d,e,f.g) should be (0000001), or g will be
OFF while all the others are ON.
1- Make a table explaining the inputs and the corresponding outputs for the 6 combinations input
(000.101), assuming the other two combinations as don't care.
2-
Find the output as a function of the inputs (A,B,C) using K-map to minimize the expressions
3-
Show your design using 2-input, and 3-input NAND gates, and inverter.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 9 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

To lit the segment on for Common anode is O a. Connect A to +Vcc and give logic 0 to K O b. Connect A to 0 and give logic1 to K O. Connect A to +Vcc and give logic 1 to K O d. Connect A to 0 and give logic1 to K
An analog voltage (0 to 5) volt is to be converted to 8 bit digital form. d. What is the error made in quantization of 2.2 volt as a percentage of the input.
Signal and system plz explain every step that how do this
19) Consider a 6-bit ADC and full scale voltage measurement range of (0-59).The Resolution will be _________. 0.30 0.06 0.92 1.00
Give the verilog and testbench code. If a combinational circuit for a BCD to seven-segment code converter that will input a BCD number and output it on a seven segment common- anode display. The code converter will only display the number 8. The converter wil turn the display OFF for all other valid BCD digits except digit 9 which will never occur.
Sketch the electronic symbol (schematic) for the following components/ devices. Briefly describe the function of the electronic component and use the IEEE/ANSI standard symbol as indicated below. LED NPN BJT PNP BJT
In a PCM system, if maximum frequency of the input analog signal is 5 KHz and number of levels in the quantizer is 256. What will be bandwidth of the transmitted PCM signal?
An analog signal varying between 1V and 3V will be converted to digital and the signal voltage value will be displayed on the LCD screen. The signal to be measured will be between 1V and 3V. 3 analog signals will be read using the AN5, AN6 and AN7 pins. Values in these signals will be displayed one by one on the LCD screen as digital and voltage values. Draw the circuit diagram and write the PIC C codes.
Please answer the questions below: 1. The letters SCR stands for silicon-controlled rectifier. Explain the use of the word rectifier in the name. 2. What two things must happen to cause an SCR to fire or trigger? 3. How much gate current is needed to trigger a medium-power SCR? 4. In words, explain what each of the following symbols stands for: a.) IGt b.) IHO
Problem #2: Apply the input waveforms A, B and C of the figure below to a NOR gate and draw the output waveform. A B C
An analog voltage (0 to 5) volt is to be converted to 8 bit digital form. a. What is the resolution in volt. b. What is the digital representation of 2.2 volt. c. What is the largest quantization error as a percentage to full scale. d. What is the error made in quantization of 2.2 volt as a percentage of the input.
Why are optoisolators normally used between the microcontrollers and the ULN2803? a) to reduce the back emf b) to increase the current c) to increase the voltage d) to optimize the current