The pathway for a binary electrical signal between gates in an integrated circuit can be modeled as an RC circuit, as shown in thefigure to the right; the voltage source models the transmitting gate, and the capacitor models the receiving gate. Suppose theresistance is 500 2 and the capacitance is 10 11 F (10 picofarads, pF). If the capacitor is initially uncharged and the transmitting gatechanges instantaneously from 0 to 4 V, how long will it take for the voltage at the receiving gate to reach 3 V?RIt will take seconds.(Use scientific notation. Round to three decimal places as needed.)

Given: Resistance=R=500 Capacitance=C=10-11 FInput Voltage=Vin=4 V

The pathway for a binary electrical signal between gates in an integrated circuit can be modeled as an RC circuit, as shown in the figure to the right, the voltage source models the transmitting gate, and the capacitor models the receiving gate. Suppose the resistance is 500 Q and the capacitance is 10-11 F (10 picofarads, pF). If the capacitor is initially uncharged and the transmitting gate changes instantaneously from 0 to 4 V, how long will it take for the voltage at the receiving gate to reach 3 V? R It will take seconds. (Use scientific notation. Round to three decimal places as needed.)

The pathway for a binary electrical signal between gates in an integrated circuit can be modeled as an RC circuit, as shown in the figure to the right, the voltage source models the transmitting gate, and the capacitor models the receiving gate. Suppose the resistance is 500 Q and the capacitance is 10-11 F (10 picofarads, pF). If the capacitor is initially uncharged and the transmitting gate changes instantaneously from 0 to 4 V, how long will it take for the voltage at the receiving gate to reach 3 V? R It will take seconds. (Use scientific notation. Round to three decimal places as needed.)

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter8: Basic Electric Motors

Section: Chapter Questions

Problem 25RQ: List the five capacitor replacement rules.

See similar textbooks

Similar questions

An inductor, a capacitor, and a resistor are connected in parallel with a function generator. The inductor draws 100mA RMS, the capacitor draws 150mA RMS, and the resistor draws 200mA RMS. Find the magnitude of the total current.
What impedance vector (0- j15) Ohms represents:A. A pure resistance. C. A pure capacitance.B. A pure inductance. D. An inductance combined with a capacitance.
In the given circuit, a step down transformer with an RMS voltage as 110V / 11-0-11 V is used with RL =1ΚΩ. Assume diode as Germanium and the input frequency is F= 50HZ. DI CT Vin R_ D2 1- Name the given circuit . 2- Find The PIV. 3- Find Current trough load resistance. 4- Draw the Input and Output wave forms. llle
please help with this circuits problem
please solve value of Capacitor with 0.1V Ripple. And draw output ripple waveform. Explain it one by one for me thanks..
2_53528980697... -> For the circuit shown below, detemine the voltage of the -j10 2 capacitive reactance. -j5 0 ILOA(T) ==j102 jlon is Q 102 O 0.5L-90 52 A.
Problem: In electronics device laboratory, you need to use the function generator to use different types of signals e.g., sinusoidal wave, square waves, sawtooth waves and so on. Imagine you are planning to make an approximate square wave generator from a sinusoidal wave having peak voltage of [three digits before last digit of your ID] mV to use the produced square wave to study the clamper circuit. You can consider any frequency. You need to avoid using any dc power supply to save the energy. Also consider the amplitude of the produced square wave must be greater than the PIV of the diode. 1. Identify which circuit is necessary for making the generator. Illustrate input-output signals with appropriate labeling. 2. Lift the produced square wave above the x axis by the amount of [your last digit of your ID] V explaining appropriate steps. + Sinusoidal PIV
-Consider the following DT sequence, Is this signal as Power Signal or Energy signal? Determine it. * 0Snくs X [n ]= lo-n 55.n510 • ther wise Power Signal, P=85 Energy Signal, E=85 O Neither energy nor Power O Both, P=30 E=55 -Is the following signal is X(4) - Sin 3t + Sin 大t Periodic Aperiodic
Shown in the figure below is an "RLC" circuit driven by an AC power source. The AC power source has an RMS voltage of Vps(RMS) = 9.35 Volts and is running at a frequency of f = 113000 Hz. The resistor has a resistance of R = 1980 , the capacitor has a capacitance of C = 1.08e-09 Farads, and the inductor has an inductance of L = 3.71e-03 Henries. mm Vps Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit øztot Determine the numerical value of Ztot = 2384 Determine the numerical value of @Z tot Determine the current through the circuit: ● R www I(PEAK) = I(RMS) = ● ● Determine the voltage across the inductor: • VL(PEAK) = Volts Volts VL(RMS) = Amps Amps Determine the voltage across the capacitor: Vc(PEAK) = Volts Volts Vc(RMS) = = 33.85 a capacitive switcher Ω degrees C If a second circuit were connected in parallel with the resistor, this circuit would be considered as: O a high-pass filter a radio tuner O…
In the given circuit, a step down transformer with an RMS voltage as 220V | 22 V is used with RL = 3 KN. Assume diode as Silicon and the input frequency is F= 70 Hz. A D3 D1 AC in D2 D4 LOAD B 1- Name the given circuit . 2- Find The PIV. 3- Find Current trough load resistance. 4- Draw the Input and Output wave forms.
1. What impedance vector 0 – j22 represents:A. A pure resistance.B. A pure inductance.C. A pure capacitance.D. An inductance combined with a resistance.
For a series RLC circuit with a sinusoidal input voltage, the amplitude of the current passing through the circuit (I, in mA) is plotted as a function of frequency for two cases: Curve 1 with R1, L1. and Curve 2 with R2. L2 as shown in the next figure. The value of the capacitor used in the circuits is C=0.01 micro Farads. If the value of R2 =1600 Ohm then the input voltage (in volts) is: 7.5 25 110 Frequency H2 O a. 4 O b. 16 sin(9888 t) O c. 8 O d. 8 cos(6.28 f t) O e. 8 sin (6.28 R t)