The parameters of the circuit shown in Figure 1 are:B = 100, VBE = 0.7 V, VT = 26 mV, Cbc =12 pF, Cce= 15 pF and Cbe = 44 pF.Based on the circuit:i) Determine the midband voltage gain, A, =Vo.viii) Calculate the low cut-off frequencies caused by C1 and C2.iii) Calculate CE if the cut-off caused by this capacitor is 88 Hz.iv) Based on values in (ii) and (iii), what is the dominant low cut-off frequency?v) Determine the high cut-off frequency.+18V3.3k2C2=0.022µFC,=0.1µFV,20k215k2Vo1k2CE68022.73VVs

Answered: Image /qna-images/answer/f1ec83bb-ecc7-486d-b9f2-3128bc3bcd25.jpg

The parameters of the circuit shown in Figure 1 are: B = 100, VBE = 0.7 V, VT = 26 mV, Cbe =12 pF, Cee = 15 pF and Cbe = 44 pF. Based on the circuit: Vo i) Determine the midband voltage gain, A, =2 vi ii) Calculate the low cut-off frequencies caused by C and C2. iii) Calculate CE if the cut-off caused by this capacitor is 88 Hz. iv) Based on values in (ii) and (iii), what is the dominant low cut-off frequency? v) Determine the high cut-off frequency.

The parameters of the circuit shown in Figure 1 are: B = 100, VBE = 0.7 V, VT = 26 mV, Cbe =12 pF, Cee = 15 pF and Cbe = 44 pF. Based on the circuit: Vo i) Determine the midband voltage gain, A, =2 vi ii) Calculate the low cut-off frequencies caused by C and C2. iii) Calculate CE if the cut-off caused by this capacitor is 88 Hz. iv) Based on values in (ii) and (iii), what is the dominant low cut-off frequency? v) Determine the high cut-off frequency.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. Derive the lower cut-off frequency for the basic RC high-pass circuit in Figure 1. R, Figure 1.
Draw the diagram of a halfwave power supply circuit and a fullwave supply circuit. Aside from the difference between the number of diode utilized in both circuits, state the main advantage of the fullwave power against the halfwave circuit for the following scenario . When there is a defective diode (open anode- cathode ) When the filter capacitor is defective (capacitor is open)
The circuit is shown below, Vin is the sinusoidal waveform with magnitude 5V and frequency is 100 Hz, R = 1 k, C = 1 uE, the chip is supplied by + 12 V source. a) What is the waveform of Yout? b) Calculate the magnitude of Vo c) If Vin is triangle waveform, what is the output waveform? -Vout , if Vin is triangle waveform with magnitude of 5 V (peak-to-peak value is 10 V) and frequency is 10 kHz, calculate waveform of you and the magnitude of I/?
select one quickly Mod-N counters can be used for frequency ........... . a) dividing, b) subtracting , c) adding , d) multiplying.
An RLC series circuit is connected to a 20 V variable frequency supply as shown in Figure 2. Determine the following: O,SAF 202 20mH 20V Figure 2 Resonant frequency in Hertz. (b) Q-factor (c) Lower and upper half power frequencies in Hertz. (d) Bandwidth in Hertz and radians per second. (a)
I need proper solution for the following( underdstandable writing and well explained) thank you What is resonance in LCR circuit? and tell the difference between impedance and resistance?
Determine the output voltage value of a transistor amplifier circuit by frequency for 1.923 V to input voltage. Instead of. Calculate the gain in dB for the frequency given in the table. Maximum write down the frequency (s) where the gain is halved in terms of power (3dB). Frequency curve draw as
Signal flow graph
What is the voltage gain for the medium frequencies of the circuit in the figure?
Q.) Figure below divider bras amplifier Circuit. Givent the model Parameter : gm = 5o mS emitter (CE) Voltage BJT hibrid- TT Shows a Common riT: 6 Kr and to %3D : 00 +Vc. RI C2 Tooks touf RL Vo ihe 200 RE TCE Vs 20 a Draw the Ac eQuivalent at low Freauency Circuit Zi and b.) Determine inPut impedance at mid FreaUincy OutPut imPedance Z0 c.) Calculafe two low Cut -oFF FreQuen Cies FLC1 and FLC2 Ci and E2 respectively Such as due to the exterda al capacitors
For the given circuit below, the RF generator is set to EXT MOD, 500kHz. RF GEN 500KHZ R1 2702 R2 10K ELECTRONIC VOM 0.0047pF a) What is this circuit? b) Is there an RF signal across R2? c) Draw the expected signal waveform across R1 d) Draw the expected signal waveform across R2 e) What is the expected frequency of the signal across R2?
Consider the circuit of Figure 1, with a periodic square signal voltage source at a frequency f = 500 [Hz], consider R = 1600 [22]. Solve the circuit and plot on graph paper (minimum 10 values between 0 and 2 milliseconds) the total current response, taking into account the source Vin = 24 [Vp]. Note: identify in the graph maximum and minimum points of the total current response. Vin CH1 L m 160 mH, 4 Q CH2 REF Figure 1. Series RL circuit. Note: to do by differential equations and not to use laplace