The horizontal bar ABC is supported by a pin at A and the two rods with identical lengths and cross-sectional areas (2 sq.in.) The rod at B is steel and the rod at C is aluminum. Neglecting the weight of the bar, determine the stress in the steel rod when the force W= 10 kips is applied. Use Es=29 × 10^6 psi and Ea=10 x 10^6 psi. Express your final answer in psi to the nearest whole number. Note: Do not include the unit in your answer. - 3 ft B A 5.5ft 1.5 ft →

The horizontal bar ABC is supported by a pin at A and the two rods with identical lengths and cross-sectional areas (2 sq.in.) The rod at B is steel and the rod at C is aluminum. Neglecting the weight of the bar, determine the stress in the steel rod when the force W= 10 kips is applied. Use Es=29 × 10^6 psi and Ea=10 x 10^6 psi. Express your final answer in psi to the nearest whole number. Note: Do not include the unit in your answer. - 3 ft B A 5.5ft 1.5 ft →

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. The bar AC is supported by a pin at A and a cable that runs from B to E around the frictionless pully at D. If the allowable tensile stress oallow = 5.2 ksi for the cable, determine the required minimum diameter (inch) of the cable. The cylinder (connected at C) weighs 890 lb. Neglect weight and thickness of the bar AC. D 4 3 A C 5 ft 5 ft -4 ft 890 lb
The cylindrical steel column has an outer diameter of 4 in. and inner diameter of 3.5 in. The column is separated from the concrete foundation by a square bearing plate. The working compressive stress is 26 000 psi for the column, and the working bearing stress is 1200 psi for concrete. Find the largest force P that can be applied to the column. Express your answer in Ib. 4 in. 3.5 in. 4/4 7 in.
The uniform 300-lb bar AB carries a 500-lb vertical force at A. The bar is supported by a pin at B and the 0:5-in. diameter cable CD. Find the stress in the cable. 4 ft A 3 ft 3 ft B. 500 Ib
An aluminum wire 3.0 m in length and 4.0 mm in diameter supports a 1000 N mass. Determine the stress in the wire.
The bar ABC is supported by a pin at A and a steel wire at B. Determine the magnitudeof force Pinlbif the elongation of the wire is 0.059 in. The cross-sectional area of the wire is 0.0039 inandthemodulus of elasticity of steel is 29001 ksi,X=3.86 ft, Y = 6.78 ft, and L = 5.6 ft. Express the final answer to four decimal places. ... B Y
The compound bar carries the axial forces P and 2P. Find the maximum allowable value of P (in lbs) if the working stresses are 40 ksi for steel and 20 ksi for aluminum, and the total elongation of the bar is not to exceed 0.2
Determine the state of stress at point q. The pipe has an inner diameter of D₁ = 1.0 in and an outer diameter of = 1.8 in. Use the exact expression for Q, if needed. Label the reultant forces on the cross section below. Report your answer (3x3 matrix) in psi to one decimal place. Do 4 in. Y 4 in. 150 lb 6 in. 50 lb 10 in. 200 lb 150 lb X N Y
The rectangular bar is connected to the support bracket with a 26-mm-diameter pin. The bar width is w=60 mm and the bar thickness is 15 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 120 MPa, the bearing stress in the bar cannot exceed 120 MPa, and the bearing stress in the bracket cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported by the structure. Answer: Pmax KN
The vertical shaft with a diameter of d = 20 mm is supported by a thrust collar that rests on a 21-mm-thick plate. The thrust collar is 16-mm thick. Assume that the load P causes a compressive stress of 190 MPa in the shaft. If the bearing stress between the thrust collar and the plate is limited to 35 MPa, determine the minimum outer diameter Dcollar that must be used for the thrust collar. Thrust collar area Plate Thrust collar d Dcollar
The rectangular bar is connected to the support bracket with a 10-mm-diameter pin. The bar width is w = 65 mm and the bar thickness is 15 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 140 MPa, the bearing stress in the bar cannot exceed 130 MPa, and the bearing stress in the bracket cannot exceed 140 MPa. Determine the maximum value of Pmax that can be supported by the structure. Answer: Pmax= i KN
The rectangular bar is connected to the support bracket with a 11-mm-diameter pin. The bar width is w = 60 mm and the bar thickness is 10 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 120 MPa, the bearing stress in the bar cannot exceed 120 MPa, and the bearing stress in the bracket cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported by the structure.
The rectangular bar is connected to the support bracket with a 27-mm-diameter pin. The bar width is w = 65 mm and the bar thickness is 10 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 125 MPa, the bearing stress in the bar cannot exceed 120 MPa, and the bearing stress in the bracket cannot exceed 130 MPa. Determine the maximum value of Pmax that can be supported by the structure. Answer: Pmax= P Mi KN