The fluid flows at a speed of 0.4 m/s through a horizontally placed smooth pipe with a diameter of 20 mm and a length of 24 m and heats an environment at a temperature of 87 oC. Considering that the pipe surface temperature remains constant, inside the pipe; a) In case of water flow, b) In case of engine oil leakage Calculate the heat transfer coefficient and friction factor in the in-pipe flow and compare and interpret the results.

The fluid flows at a speed of 0.4 m/s through a horizontally placed smooth pipe with a diameter of 20 mm and a length of 24 m and heats an environment at a temperature of 87 oC. Considering that the pipe surface temperature remains constant, inside the pipe; a) In case of water flow, b) In case of engine oil leakage Calculate the heat transfer coefficient and friction factor in the in-pipe flow and compare and interpret the results.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.27P

See similar textbooks

Similar questions

6.1 Determine the heat transfer coefficient at the stagnation point and the average value of the heat transfer coefficient for a single 5-cm-OD, 60-cm-long tube in cross-flow. The temperature of the tube surface is , the velocity of the fluid flowing perpendicular to the tube axis is 6 m/s, and the temperature of the fluid is . Consider the following fluids: (a) air, (b) hydrogen, and (c) water.
6.3 Steam at 100 kPa and is flowing across a 5-cm- OD tube at a velocity of 6 m/s. Estimate the Nusselt number, the heat transfer coefficient, and the rate of heat transfer per meter length of pipe if the pipe is at .
Fluid flows at an ambient temperature of 87 oC at a speed of 0.4 m/s through a smooth pipe with a diameter of 20 mm, a length of 24 m and placed horizontally, and heats a medium. Considering that the pipe surface temperature remains constant, inside the pipe; a) In case of water flow,b) In case of engine oil leakage Calculate the heat transfer coefficient and the friction factor in the in-pipe flow and compare and interpret the results.
a)Identifythe maximum velocitylimitof ammonia gas in the pipe if the flow is to be maintained as laminar flow. b)If the actual velocity of ammonia gas is 0.9 times the maximum velocitylimit, calculatethe heat transfer coefficient and heat transfer flux if the heat transfer area is 0.16m^2. c)Suppose the pipe has an outer diameter of 43.1 mm and the outer surface wall temperature of the pipe is 356 K, determinethe thermal resistance and thermal conductivity of the pipe.
Water is flowing through 40-mm diameter 4-m long tube with a rate of 2kg/s. Tube surface temperature is maintained at 100 oC and the water enters the tube at 27oC. a) What is the outlet temperature of the water? b) What is the corresponding heat transfer rate?
Resolving of Example (1-3) Two reservoirs with a difference in elevation of 15 m are connected by the three pipes in series. The pipes are 300 m long of diameter 30 cm, 150 m long of 20 cm diameter, and 200 m long of 25 cm diameter respectively. The friction factors for the three pipes are, respectively, 0.018, 0-020 and 0-019, and which account for friction and all losses. Further the contractions and expansions are sudden. Determine the flow rate in l/s. The loss co-efficient for sudden contraction from dia. 30 cm to 20 cm = 0.24. use the complex Liquid Piping system (series Piping
derive the navier stoke equation to Vz (in function r) in a cylindrical pipe with the maksimum radius of a and L as the length of the pipe in a laminar and steady flow
As part of an industrial pipe system a 6-meter-long by .5 meter inner diameter copper pipeweighing 200kg holds a lubricating oil in place while is heats from 20 deg C to 55 deg C. At thatpoint, the valve opens and allows to oil to flow through. What is the total heat transferrequired? And, what percentage of the heat transferred does the oil and copper each accountfor? (oil density = .9 kg/L , oil specific heat = 1800 J/kgC)
Consider fully developed flow in a circular pipe with negligible entrance effects. If the length of the pipe is doubled, then pressure drop will and heat transfer coefficient will Select one: A. reduce by half, remain the same B. remain the same, remain the same C. increase four times, remain the same D. double, remain the same E. increase four times, double F. reduce by half, double G. double, double
Engine oil is heated by flowing through a circular tube of Diameter D= 50 mm, length L= 25, and whose surface is maintained at 150 Deg. C. If the flow rate and inlet temperature of the oil are 0.5 Kg/s and 20 Deg.C Use the following properties: p= 852 kg/m³, o-u/p-37.5 x10-6 m²/s, k=138x10-3 W/m.K, Pr = 490, C₂= 2131 J/kg.K. u= px 0= 0.032 kg/m.s m = 0.5 kg/s Engine Oil Tml = 20 C DIA = 0.05 m 9 Ts = 150 C L = 25 m Tmo? Based on the above information. 1. Find Rep 2. Based on the value of Rep, what type of flow do we have? 3. Determine the outlet mean temperature Tm.o, with the average heat transfer coefficient = 33.12 W/m^2.K
Local Nusselt number for fully developed (hydrodynamically and thermally) turbulent flow in a smooth circular tube is defined by Nup-hD/kr, where h, D, and kr are the convective heat transfer coefficient, tube diameter, and fluid thermal conductivity, respectively. The friction factor for the smooth circular tube is given by the Blasius correlation, f-0.316Red ¹/4. The Reynolds number is defined by Rep-prviD/μr, where pr, vr, and ur are the fluid density, fluid velocity, and fluid viscosity, respectively. The Blasius correlation is applicable to Rep<2×10¹. Considering the analogy between velocity and thermal boundary layers and using the Blasius correlation, express the local Nusselt number using Reynolds and Prandtl numbers in the form of NuD-A-ReDxPr. The Prandtl number is defined by Pr-war, where and ar are the fluid kinematic viscosity and fluid thermal diffusivity, respectively. Note that the local Nusselt number formula should be applicable to Rep<2×10 and 0.6
Water at a temperature of 20 oC with a mass flow rate of 0.015 kg/s enters the pipe 2.5 cm in diameter with a uniform surface temperature of 90 oC. a) Determine the length of the thermal inlet region, Lt.b) If it is assumed that the flow is hydrodynamically and thermally formed, calculate the convection heat transfer coefficient and the length of the pipe required to heat the water to 70 oC.c) What is the rate of heat transfer to the water?d) Calculate the friction factor and pressure drop.