The 40-lb crate slides down the curved path in the vertical plane. If the crate has a velocity of 3.7 ft/sec down the incline at A and a velocity of 27.6 ft/sec at B, compute the work U; done on the crate by friction during the motion from A to B. 3.7 ft/sec 19' B 27.6 ft/sec 24' Answer: Uf = i 295.36 ft-lb

The 40-lb crate slides down the curved path in the vertical plane. If the crate has a velocity of 3.7 ft/sec down the incline at A and a velocity of 27.6 ft/sec at B, compute the work U; done on the crate by friction during the motion from A to B. 3.7 ft/sec 19' B 27.6 ft/sec 24' Answer: Uf = i 295.36 ft-lb

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The two blocks started at rest. The surface of the inclined plane is frictionless. (note: neglect mass and friction of the pulley) Given: Weight of A=230 lb. Weight of B=300 Ib. Calculate: a) acceleration of A (ft/s"), 30° with the horizontal b) Acceleration of B (ft/s"), downward c) the tension in the cable (Ib.) B 30°
In an amusement park ride, riders stand against the vertical wall of a spinning cylinder. The floor falls away and the riders are held up by friction. If the radius of the cylinder is R, find the minimum number of revolutions per time necessary if the coefficient of friction between a rider and the wall is given.
Q3: As shown in figure, find that at what distance body A will attain a velocity of 3 m/s from A 2000 N when starts rest. Assume coefficient of friction as 0.2 for block and and pulleys frictionless and weightless. surface are 3) DOM www N 00
Neglect friction of the 55-lbf collar against its vertical guide and compute the velocity of the collar after it has fallen 7ft., starting from 22 ft/sec. in the position shown below. The unstretched length of the spring is 3ft. compute the velocity of the collar after it has fallen 7ft., starting from 22 ft/sec. in the position shown below. DO NOT ROUND OFF IN THE SOLUTION. ROUND OFF ONLY IN 2 DECIMAL PLACE IN THE FINAL ANSWER
A brake test for an automobile is conducted. During the brake test, the automobile of mass 1800 kg (including driver) is travelling at the speed of 110 km/hr as it passes point A, and the car descends a hill of 1in 2 (Sine). The driver applies brakes so as to bring the car speed at B to 50 km/hr. The total frictional resistance to motion is 235 N. Using Work-Energy Method, Calculate the following required to bring the car to 50 km/hr from 110 km/hr in 210 m (From Point A to Point B) B Determine the Value of Total Energy about Point A TE= Determine the Value of Total Energy about Point B TEb= Determine the Value of Breaking Force needed Fb= N A
6. A car weighing 5000-kg is on a banked curve as shown. The coefficient of friction between the road and the tire of the car is 0.50. It is rounding the curve of 200 m radius at maximum speed. Determine the maximum speed and the frictional force acting on the wheels. 3 D 11 2.5
A 100-lb block is pushed at constant speed for a distance of 20 ft along a level floor by a force that makes an angle of 35° with the horizontal, as shown in Fig. The coefficient of friction between the block and the floor is 0.35. Determine The work done on the block by the force. F. 35°
3- (KINETICS) The coefficient of friction under each of the weights shown in Fig. is 0,1. Solve of the acceleration of the weights and the tension T in the rope. Neglect the friction and weight of the pulley. 1000 N 1000 N 30 60 Act
Consider the following diagram. m1=20 kg and m2= 10 kg. The system is being pulled by an applied force of 200 N. directed 50" above the horizontal. The coefficient of kinetic friction between the block and the surface is u-0.2. 50 m, 20kg Coefficient of friction 4=0.2 10 kg. 309 7) Calculate the acceleration of the system. Your answer 8) Calculate the magnitude of the Tension on the rope. Your answer N 00
a. A vehicle with the handbrake drawn must be pushed and moved. The vehicle weight is 1200 kg, and the force required to push the vehicle is 300 kg (G=10 m/s2 can be taken). Determine the value of the coefficient of friction that occurs when the wheels of the car make a sliding movement on the asphalt. As the car is pushed and moved, the speed of the car increases to 3.6 km/h. Find the power spent on friction b. An oil film was formed under the wheels while the same vehicle was pushed with the handbrake drawn, and the vehicle thrust was reduced to 6 kg (G=10 m/s2). Determine the value of the coefficient of friction that occurs between the molecules of the lubricant. The speed of the vehicle increases to 3.6 km/h when the vehicle is moved by pushing on the oil film. Find the power spent on friction
If there is n friction in the system, the Lagrange's equation will be based only on kinetic energy and protentional energy only. Select one: O True O False III O
3- (KINETICS) The coefficient of friction under each of the weights shown in Fig. is 0,1. Solve of the acceleration of the weights and the tension T in the rope. Neglect the friction and weight of the pulley. 1000 N 1000 N 60 30