temperature of 21 degrees Celsius, wet bulb temperature of 14 degrees Celsius and the second at dry bulb temperature is 28 degrees Celsius, wet bulb temperature of 20 degrees Celsius with mass flow rates of 1 kg/s and 3 kg/s for the first and second respectively . Find the moisture content ,enthalpy ,and the dry bulb temperature for the mixture and plot the process on the psychrometric

Q: PROBLEM 2: A support block is acted upon by two forces as shown. Knowing that the coefficients of fr...

A: To find Pmax the calculations are made by considering P as the force for impending motion of the blo...

Q: Read the questions carefully and answer with complete solutions and units. Use the steam tables prov...

A:

Q: Determine the x, y, and z components of the angular momentum HO of the particle about point O using ...

A:

Q: rate of change of the speed of the ball (a) just after launch and (b) at apex. Neglect aerodynamic d...

A: To find Radius of curvature & rate of change of speed

Q: Water in the reservoir flows through the 8-in diameter pipe at A into the turbine as shown in fig. I...

A:

Q: Subject: Hydraulics Topic:Accelerated Liquids in Relative Equilibrium A cylindrical bucket, 35 cm de...

A: The minimum speed of rotation that the bucket can have without permitting water to spill is 3.26 rad...

Q: or the lightweight truss which is loaded as shown 10 kN 5 kN 6 m - 6 m ▼A B C 4 m D E -6 m 3 m 3 m B...

A:

Q: haust is the main system exhaust. The zones are to held at 75 °F db / 50% RH when the total heat gai...

A: Ans 1) In the recently referenced circumstance, a course of action owner requirements to override on...

Q: temperatures: Evuporator islet water ta, °C FO 15 10 15 台1 ConúenseT inici watei ib C Continue itera...

A: according to the given data

Q: For the lightweight truss which is loaded as shown 10 kN 5 kN 6m VB -6 m A 4 m D E: 6 m 3 m 3 m Dete...

A: From the figure : Number of members M = 7 Number of joints        j = 5

Q: All terminals have a defined wire size range. If I had a wire of 2.0mm / 15 AWG, what terminal shoul...

A: Calculate the cross-sectional area of the wire by using the 15 AWG. 15 AWG=1.65 mm2

Q: A father plays with his little son on a frozen lake. They stood facing each other, put their hands t...

A: Given     Acceleration of father, a = 0.8 m/s2               Mass of father, m = 4 M  Where,     M i...

Q: 4. Draw the shear and moment diagrams tor the shat. The bearings at A and 8 exert anly vertical reac...

A:

Q: Explain and differentiate the concept and processes of Carnot cycle, Otto Cycle/Gasoline engine, Die...

A: 1 2

Q: the laboratory at 2000 rpm, when it was found that the brake torque w with all cylinders firing but ...

A:

Q: A city has an infestation of mosquitos. There is a public fear of meningitis. Citizens demand that t...

A: When a human beings come under the exposure of malathion mixed with kerosene, it is dangerous for a ...

Q: Question 39 of 46 The force of magnitude Facts along the edge of the triangular plate. Determine the...

A: Rotational effect causes by force about point is called moment.

Q: A 155-MW two stage ideal reheat cycle steam power plant has the steam generator and condenser operat...

A: In a reheat cycle, the expansion of steam is carried out in two or more stages. After partial expans...

Q: Consider steady-state conditions for one-dimensional conduction in a plane wall having a thermal con...

A:

Q: At a temperature of 400 F, find the size of the orifice of the pressure relief valve to be used in a...

A: Given a Pressure cooker,The temperature inside is 400 F or 204.44o C

Q: Find the elbow forces on the x and y direction.

A:

Q: WHAT IS THE RESULTING PRESSURE IN PSIA WHEN ONE POUND OF AIR IS AT 15 PSIA AND 200°F IS HEATED AT CO...

A:

Q: The basketball player likes to release his foul shots with an initial speed vo = 25.5 ft/sec. What 2...

A:

Q: A gage pressure of 52.3 kPa is read on a gage. Find the absolute pressure if the elevation is: (a) A...

A: Given:Gage pressure, Pg=52.3 kPa

Q: Determine the x- and y-coordinates of the centroid of the shaded area. 200 mm 200 mm 150mm 125mm 60 ...

A:

Q: 1. Determine the maximum positive bending moment in the beam in kN-m. 2. Determine the maximum shea...

A:

Q: The stresses acting on element A in the web of atrain rail are found to be 40 MPa tension in the hor...

A: Given   Stress =  40 MPa tension             = 160 MPa compression Shear stress = 54 MPa Find   Prin...

Q: At a temperature of 400 F, find the size of the orifice of the pressure relief valve to be used in a...

A:

Q: PROBLEM 3: Determine the tension in each of the three ropes supporting the crate.

A:

Q: What are the materials and equipment in grinding high speed steel lathe tool bits? Explain.

A: High speed steel lathe tool bit is a very hard tool material, which is very tough to grinde. Its a c...

Q: 2. The state of plane stress at a point is shown on the element in (a). Determine the maximum in-pla...

A:

Q: Assume 20 lbm of an ideal gas with R=50 ft-lb/lb-R and k=1.18 are heated from 75 to 200F. What is th...

A:

Q: Determine mass of air ?

A: Given data:   Volume,v=2.85 m3Temperature,T=303 kGauge pressure, pgauge=0.5 barGas constant, R=287 J...

Q: The 0.5 m x 1.2 m wall of an industrial furnace is constructed from L = 0.15-m-thick fireclay brick ...

A:

Q: A uniform ladder 18 ft long and weighing 120 lbs rests against a smooth wall. The angle between the ...

A:

Q: 20. What is the minimum diameter for a plug weld deposited in a hole drilled in a plate '/2 in. (12....

A:    Plug welds are circular welds that connect two surfaces by passing through a tiny hole in one of ...

Q: a small hole prior to planting a tree, a homeowner encounters rocks. If he exerts a horizontal 209-N...

A:

Q: Determine the moment of the 260-lb force about point A and about point O.

A:

Q: Anexperimental device imparts a force of magnitude F = 67 lb to the front edge of the rim at A to si...

A:

Q: Problem 3.20 Hollow shaft with D = 50 mm and d = 46 mm of L = 1m and G 83 GPa (steel). If the shaft ...

A:

Q: 1. Which sprinting techniqu uds effective: flexing the knee swing leg more during the

A: Sprinting technique is nothing but the forward momentum given focusing on the adjustments in your kn...

Q: Hello, I have some diagrams I have filled out for practice that I would like to use to study for an ...

A: Diagram 1. E - relief valve A- gear pump D- rotor F- internal gear C- internal and external gear pum...

Q: Determine the maximum flexural stress experienced by the beam in MPa.

A: TO FIND : The maximum bending stress ; GIVEN:

Q: A gas initially at 15 Psia, 2ft3 undergoes a process to 90 Psia, 0.6ft3. During which the enthalpy i...

A:

Q: Force developed on the plate ?

A: Given: Velocity,v=68 m/sFlat plate moving away from it at,u=58 m/sThe cross-sectional area,A=0.02 m2...

Q: For a hotshot wind tunnel with T=5000k and P=100 MPa. Calculate and plot Ma function of ratio A/At f...

A:

Q: give an example of METHOD OF HEAT TRANSFER that can only found and we can do in kitchen or home. Ple...

A:

Q: In the assembly shown below, the links BD is made of brass (E = 105 GPa) with cross- sectional area ...

A:

Q: The two shafts are made of A-36 steel (shear modulus G = 75 MPa). Each has a diameter of 25  mm, and...

A: Given data, Shear modulus of shaft material, G = 75 MPa Diameter of shaft d = 25 mm Support A, B and...

Q: A mechanic is reinstalling a newly-sharpened blade on a lawn mower. A wedged-in block of wood at C p...

A: