!! Show Complete & Detailed Solution w/ FBD !! The concrete post in the figure, is reinforced axially with four symmetrically placed steel bars, each of cross-sectional area 750 mm2. The moduli of elasticity are 200 GPa for steel and 14 GPa for concrete. A 2000-kN axial load is applied. Compute the: a. axial force in concrete; b. axial force in the steel bars; c. stress in the concrete;

Q: etermine the cross-section of a rectangular beam loaded as shown in the figure if the allowable ural…

A:

Q: 75 kN A -8m B 23 kN/m 8m

A:

Q: A solid constant-diameter circular shaft is subjected to the torques of TA = 490 lb-ft, TB = 1080…

A:

Q: The total irrigation depth of water, required by a certain crop in its entire growing period of 150…

A: given- growing period=150 days=150×24×60×60 secdepth of water required=25.92 cm=0.2592…

Q: Assuming that the walls are rigid, calculate the axial force in each segment after the loads are…

A:

Q: Soil is to be excavated from a borrow pit which has a density of 1.75 gm/cc and water content of…

A:

Q: The five-bolt connection must support an applied load of P = 2600 lb. If the average shear stress in…

A: given:Total number of bolts, n=5Load, P=2600 lbAverage shear strain limited to 27 ksiz=27 ksi

Q: 1. Using the conjugate beam method, determine the slope and deflection at point B of the beam ABC…

A:

Q: Question 5 Water flows through a pipeline whose diameter varies from 20 cm to 10 cm in a length of…

A:

Q: Two 12 in 20.7 lb channels are latticed together to form the section in the figure. Determine how…

A: Given:A=6.03 in2Iyo=3.9 in4Ixo=128.1 in4x¯=0.70

Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam…

A: Given A cantilever beam  Required  Shear force diagram and bending moment diagram using graphical…

Q: Problem 2: A square shape catchment with 100 km² area has five raingauge stations at the center of…

A: Given: Square catchment area of 100 KM2 Station and precipitation of five rain gauge station are…

Q: 10.5 An aluminum column 6 ft long has a solid rectangular cross section 3/4 in. by 2 in. The column…

A: Given  E= 10.3 × 106 psi

Q: 1. Determine all reactions of supports using force method. El is constant. 100 kg 50 kg 2m AMALM 4m…

A: Given Data: PL = 100kg and 50kg

Q: 2. A flanged bolt coupling consists of seven 12-mm diameter bolts arranged on a bolt circle 300 mm…

A:

Q: compute the temperature change of the assembly that will cause a tensile stress of 50 MPa in the…

A:

Q: Line AB has an azimuth of 322° 40' 20" (origin point is B). Find the principal angle in degree for…

A: Given data : Line AB has an azimuth of 322° 40' 20" Find the principal angle in degree for line AB

Q: A pipe having a diameter of 2 feet with roughness coefficient of 0.013 flows in full. If the slope…

A:

Q: P Q B D E 2 ft |—3 ft——▬3 ft— 2 ft P

A:

Q: A sediment pond has been designed to take flood water from a small river that is high in suspended…

A: Waste water treatment for Ponds : Storm Event : It means rainfall event which produce more than 0.1…

Q: if the corrected vertical and horizontal alignment of the sides of the traverse (ABCDE) are as they…

A: To Determine Coordinates of points B,C,D & E

Q: Water is to be siphoned from a tank at the rate of 0.0892 m^3/s. The flowing end of the siphon pipe…

A:

Q: Draw the shear and moment diagram of the loaded beam shown in the figure. Determine the Vmax and…

A: To Determine The shear and moment diagram of the loaded beam shown in the figure.  Vmax and Mmax.

Q: PROBLEM 1 Find the moment of inertia of the section with respect to x-axis (lx). Y 1m- 1 m 4 m -3 m-…

A:

Q: CONCRETE PRESSURE We are pouring 12-foot-high concrete columns with self-consolidating concrete, and…

A: Given data:- Height of column,  H = 12 ft. Timing of placed of column, t = 1 hour Weight of self…

Q: Compute the midspan deflection for the simple beam loaded as shown [a=1m, b = 2m, P = 10kN, w =…

A:

Q: A cylindrical tank, 1m in diameter and 2m high weighs 1090 Newtons. The tank is to float in water…

A:

Q: A rectangular flume of most efficient proportion b = 2d has a perimeter of 6 m. and carries a…

A: Given: The perimeter of the rectangular flume is 6 m. The discharge of the rectangular flume is 4.70…

Q: Draw the shear-force and bending-moment diagrams for the beam shown. PROVIDE A DETAILED AND COMPLETE…

A: Shear force :  Clockwise positive  Anticlockwise negative  Bending moment:  Clockwise negative…

Q: it supports the force of 600KN. Use a factor of safety against failure of 1.50. Also, find the…

A:

Q: Use the Conjugate beam method to determine the slope at A and displacement at C. EI is constant. 5…

A:

Q: From the given beam shown below, find the moment value at point A (MA).

A: Due to moment applied at point c, a point load devoloped 75kn at free end D. So now there are no…

Q: in temperature to be taken into account ICAO is

A: This question is taken from airport engineering

Q: 50 MPa in the steel r

A: Given:- W=80 kN, tensile stress of 50 MPa in the steel rod To find:- temperature change

Q: Determine the member forces for members IJ,CJ and CD of the truss below. H K F 40 kN 40 KN 40 kN 40…

A:

Q: Draw the shear and bending moment diagrams for each beam loaded as shown 1. 60 k 150 k-ft B C -10…

A:

Q: The rigid bar of negligible weight is supported as shown in the figure. If W=80 kN, compute the…

A:

Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam…

A:

Q: A 5-m length solid steel shaft is subjected to a torque of 15 kN-m. If the angular deformation of…

A: Given: Torque  Angular deformation  Modulus of rigidity To find: Minimum diameter Maximum Shear…

Q: The particle size distribution curves for three soils - A, B and C - are shown in Figure Q-2 on page…

A: To Determine a. The effective size D10 , average particle size D50 , uniformity coefficient Cu , and…

Q: Z C310 x 45

A:

Q: A and B are the two points on the opposite banks of a pond. To continue the line past this obstacle,…

A:

Q: 3. The 50-kg uniform pole is on the verge of slipping at A when 0 = 45°. Determine the coefficient…

A:

Q: Fill in the blanks: The steel rod is stress-free before the axial loads P₁ =169 kN and P2 = 88 kN…

A: Given data in question  Loads Area Elasticity modulus  Length Statically indeterminate  To find out…

Q: Find scale and units of map 2.Find DATUM & UTM zone

A: Scale of the map as shown in the figure is =1 cm= 1km   = 1:10000 Unit of the map is m as the data…

Q: roblem 1. For the shaded area below, a) Determine the moments of inertia with respect to the x-axis…

A: from the given data:

Q: ma rock blasting activity, permissible particle speed is 50 mm/s. The velocity measured during the…

A: Explanation :  Since the velocity measured is more than the permissible particle speed, hence it can…

Q: Q6: Designing a Rigid Pavement Using the AASHTO Method (Find D) Effective modulus of subgrade…

A: K = 480 lb/in³ or Pci  Sc = 725 lb/in²  J = 3.9 Ec = 4.5 × 10⁶ psi  CD = 1.0  ∆PSI = 1.5  Zr =…

Q: This equipment is typically used in cement manufacture and is essentially a long continuous rotating…

A: Cement is manufactured by different equipments like rotary kiln , shell and tube heat exchanger .

Q: Q4. Consolidation is a term used to describe the volume reduction of: (a) Saturated clay (b) Dry…

A: The definition of consolidation is as follows: Consolidation is the process of reduction of volume…

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.