II IS CourseEHide bThe 30 kg block is supported by two springs having the stiffness shown. Determine the strech of spring AB, S(AB):0.4 m0.3 m0.4 mkc 1.5 KN/mA 1.2 kN/mSelect one:O a. S(AB) = 0.22 mOb.S(AB) = 0.175 mS(AB) = 0.12 mO d. S(AB) = 0.5 mforce E=30ni.200i+50ok N about the y-axis is.

Answered: Image /qna-images/answer/885b9f7a-361b-4566-ae9b-d5e0c352d0a6.jpg

Answered: S(AB) = 0.175 m !!

Engineering

Mechanical Engineering

S(AB) = 0.175 m !!

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

asap
A weight Wis dropped from a heighth on the mid-span at C of a simply-supported beam as shown, where the spring always remains vertical and is at its natural length when the beam is horizontal. For W-90 lb and the stiffness of the spring k-313 lb/in, determine the static elongation of the spring (apring). Le., h-0. [in] W 40" h 1"I
Problem A 1) Find the equivalent spring,N/mm 2) Find the force, F KI K5 k k K2 x=10 mim k 00000 0000 k КЗ K4 K6 ....... ...... ...... ...... ........... .. ........
PROBLEM A 1) Find the equivalent spring, N/mm 2) Find the force, F k. Kl: =7 K5. =11 0000 K2 =8 X-10 mm k К3 -9 КА -10 К6 -12 ....... ........ .....
Clear my choice Question 28 Compression coil spring is subjected to load of 500 N is having the mean diameter of 65 mm, wire diameter of 6 mm, number of active coil is 18. Find the shear stress without curvature? Select one: 2. O a. 867 N/mm O b. 400.81 N/mm O C. 481.6 N/mm O d. 563.56 N/mm hp
The electric motor exerts a 500-N-m torque on the aluminum shaft ABCD when it is rotating at a constant speed. The torques exerted on pulleys Band Care as shown. Take a = 1.4 m, b= 0.9 m, and G= 27 GPa. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 300 N. m 200 N. m 45 mm 44 mm 40 mm Im Determine the angle of twist between Band C. The angle of twist between Band Cis|
what is the compression in 2 springs after the block A with 50 N is falling off on it from the rest note :-Initially both springs are unstretched. A 10m 5m 20N/m = 30 N/m
If the wire diameter of a compressive helical spring is increased by 2%, the change in spring stiffnes: (in %) is (correct to two decimal places).
6-29E. For the crane system of Figure 6-27, determine the hydraulic cylinder force required to lift the 2000-lb load. A O 2.5 ft 45° B # 2000 lb CYLINDER 75° Figure 6-27.
A typical compound helical spring consists of two coaxial closed coil spring having the following particulars: Outer spring 1: mean coil diameter = 100 mm Wire diameter = 12.5 mm No. of turns = 15 Inner spring 2: mean coil diameter = 75 mm No. of turns = 20Both the springs are of equal initial length when unloaded. Ifthe working stress for each spring is to be same. The modulus of rigidity for the wire material is 80 GPa. Calculate the following:a. Diameter of steel wire for inner spring. b. Stiffness of inner springc. Stiffness of the compound spring. I need answer ASAP. Thank you!
Part A 6 ft Ax= -106.7 lb, Ay = 80.0 lb Ax= -46.7 lb, Ay = 45.0 lb == Ax-53.3 lb, Ay = 40.0 lb Ax = 13.3 lb, Ay 10.0 lb O Ax O O Ax -4 ft 4 ft- 0.5 ft Determine the horizontal and vertical components of force at pin A. 80 lb B
A helical spring with a load range of from 450 N to 800 N from valve-closed to valve-open conditions is used to close the valve of a spring-set relief valve having a lift of 10 mm. Assuming the spring wire to be of chrome vanadium steel, the spring is rendering average service, determine the diameter of the wire if the spring index is 7 and Sg - 420 MPa. Use G=83GPA. Select one: O a. 2.4-mm wire O b. 5-mm wire O c. 6-mm wire O d. 7-mm wire