Rods AC and BC are used to suspend the 205 kg mass.A60°-60°BCIf each rod is made of a material for which the average normal stress can not exceed 150 MPa,determine the minimum required diameter of each rod to the nearest mm.Express the answer as an integer with the appropriate units

Answered: Rods AC and BC are used to suspend the…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 40 kN if it developed a stress of 35 MPa. Take note that the inner diameter is 3/6 of the outer diameter.
2-2. mechanism must transmit a tensile force of 5 kN A steel rod 10 m long used in a control without stretching more than 3 mm, nor exceed- ing an allowable stress of 150 MN/m². What must the diameter of the rod be? Give the answer to the nearest millimeter. E 210 000 MN/m2.
Determine the minimum cross-sectional area of a steel bar required to support a tensile force of 50 kips if the allowable unit tensile stressis 20 ksi.
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ = 15 kips, F₂ = 34 kips, and the normal stress in each rod must be limited to 21 ksi, determine the minimum diameter d₁ required for rod (1). F₂ (1) F₁ 1.023 in. 0.954 in. 0.682 in. 1.108 in. 0.585 in. F₂ B C d₁ -d₂
The boom is supported by the winch cable that has an allowable normal stress of allow = 24 ksi. It supports the 5000-lb crate when = 20°. V Part A Determine the smallest diameter of the cable to the nearest 1/16 in. Express your answer to three decimal places and include appropriate units. Value Submit Units Request Answer ?
2. The bar AC is supported by a pin at A and a cable that runs from B to E around the frictionless pully at D. If the allowable tensile stress oallow = 5.2 ksi for the cable, determine the required minimum diameter (inch) of the cable. The cylinder (connected at C) weighs 890 lb. Neglect weight and thickness of the bar AC. D 4 3 A C 5 ft 5 ft -4 ft 890 lb
Determine the tensile stress in a bar of 20 mm diameter when it is subjected to a pull of 450 N.
A steel bar having cross sectional area of 100 П mm² is subjected to a tensile force of 40 kN. Π Determine the tensile stress.
Determine the normal stress in each section of the assembly. The diameter of the solid shaft of each section is 0.50 inches. Give the answer in lb/in?. Assume Point A is a fixed support and the block at A is rigid. Indicate if it is in tension or compression. 3.50 kip 1.75 kip 5.00 kip B 3.50 kip A 1.75 kip 18 in: 12 in. 16 in: CAR= units II II
06. The lap joint is connected by three 20-mm diameter rivets. Assuming that the axial load P = 50 kN is distributed among the three rivets, find a. the shear stress in each rivet; b. the bearing stress between the plate and a rivet; the maximum average tensile stress in each plate. С. Express your answer in MPa 130 mm O O O 3/4 25 mm 25 mm
Shown is the stress-strain curve developed from the tension test of a metal alloy bar. The specimen used to develop the stress-strain curve has a round cross-section with a diameter of d = 7 mm and a gauge length of L = 370 mm. Determine the load that must be applied to the specimen to stress the specimen to it's 0.2% offset yield. Express your answer in kN to the nearest whole kN. Your written solution must also include the length of the specimen when stressed to the 0.2% offset yield stress. σ (MPa) 700 600 500 400 300 200 100 0 0.02 0.04 0.06 0.08 0.10 0.002 0.004 0.006 0.008 0.010 € (mm/mm) P d
The homogenous bar that weighs 5000 Ib is supported by a pin at Cand a cable that runs from A to B around the frictionless pulley at D. If the diameter of the cable is 0.8 inch, calculate its axial stress. Express your answer in ksi (kips per sq. inches) with one decimal place only (Note: Give only the numerical value of the answer. DO NOT INCLUDE THE UNIT IN THE ANSWER) * D F 3 ft 5 ft 5 ft

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Rods AC and BC are used to suspend the 205 kg mass. A 60° -60° B C If each rod is made of a material for which the average normal stress can not exceed 150 MPa, determine the minimum required diameter of each rod to the nearest mm. Express the answer as an integer with the appropriate units