R1 20µF R2 Vc 0.5mH R3 12V 0.4mH 10µF 25V Assume the above circuit has been in this state for a very long time. Determine the voltage across the 20µF capacitor Vcgiven R1=40 R2 =52 R3 =42 Note: Round your answer to the nearest single digit decimal place. Your answer should be in Volts. For example, if you compute 15.43 Volts then ente

R1 20µF R2 Vc 0.5mH R3 12V 0.4mH 10µF 25V Assume the above circuit has been in this state for a very long time. Determine the voltage across the 20µF capacitor Vcgiven R1=40 R2 =52 R3 =42 Note: Round your answer to the nearest single digit decimal place. Your answer should be in Volts. For example, if you compute 15.43 Volts then ente

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter19: Capacitors

Section: Chapter Questions

Problem 2PA: You are an electrician working in an industrial plant. You discover that the problem with a certain...

See similar textbooks

Similar questions

A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Va.. (t) 10 kO 8V 10 kO Vin Vin(t) D2 Vout(t) RL Ims D1 6V -8V 4V Page | 1
What voltage is boosted at the output of a multiplier.Choices: average, rms, peak, or instantaneous Which assumption is not used in the analysis of multipliers?Choices: a capacitor will not discharge, start with the cycle of the source that will forward bias the nearest diode, the output will always be multiplied, or a single diode is forward biased at a time A voltage multiplierChoices: multiplies the output voltage, has very high voltage and low current ,can employ inductors, or may not have equal numbers of diodes and capacitors A voltage regulator maintains constant voltage at the load regardless of variations atChoices: the input and output, the load, source, or in the environment Between a lower percent regulation and a higher one, which is better?Choices: lower or higher
Half-wave 50Hz sinusoidal uncontrolled rectifier circuit with a peak voltage value of 100V and a source inductance of 8mH is feeding a highly inductive load of 8A. The average value of the output voltage and power delivered are, respectively and what is the communication angle (u) Power Electronics
Full-wave rectified sine wave circuit is used to measure the RMS value of a half square wave with the help of PMMC meter. The meter was actually calibrated for sine wave. The circuit uses a meter movement with a full scale deflection current of 200uA and internal meter resistance of 5kΩ. Assuming Non-ideal diodes having resistance 1kΩ, Analyze the circuit to determine the value of series multiplier resister and the corrected RMS voltage, if meter is to read 225V RMS full-scale.
A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Vaue (t). 10 k. 8V 10 kN. D2 RL Vourlt) Vin= Vin(t) Ims D1 6V -8V 4V Page | 1
For the network shown in figure (3), if the switch is closed for 2usec and then opened for Susec, find mathematical expressions for vi and in of both periods of time and then plot the waveforms of vL and i as a function of time.
For the circuit shown in find: (i) the output voltage (ii) the current through Zener diode (Given: Zener diode break down voltage Vz=5.6V) 2002 1-2022 9V 80092 4 7-82190-2023/0 190-023/04/01-2221762157-87190-2023.040
Full-wave 50 Hz sinusoidal controlled rectifier circuit with a peak voltage value of 100 and a source inductance of 8mH is feeding a highly inductive load of 8A. At a firing angle of 60 , the average value of the output voltage and power delivered are, respectively: Power Electronics
Electrical Engineering please solve this thank you The following values are given for a shocdley diode Vi (derel vollaye) • 0.025 V Is (Deverse salunalia cmal): 10X10A -15 Given voltaye eg ^: v(t) = 0.7+ 8 Vr cosut IA RL= 50 0 %3D Find avg. powen diipted in shochly diode € ay.power deliveud to load
1. Find the voltages across the following components (a and b) after 1 second. The Capacitor is initially charged at 10V while the voltage source is 1V. Resistor R is 103 ohm while capacitor C is 1mF. a. Capacitor C b. Resistor R c. What is the best 1st order DE Method applicable to this problem?
2:50 1 LTE O Motor Warning Light Instructions PHYS&110-VHY-S21-PHYSNON-SCIMAJORSWLAB-.. STEP 3 Now add a red LED (D1 in the main schematic) in series with 500N of resistance (shown as R1 in the main schematic). How you choose to arrive at 5002 is up to you. SW1 PSB D2 D3 1N4007 5 V D1 Blue Red R3 10 ka R1 500 Q • What happens now when SW1 is (and the PSB is turned on)? • What happens if you turn the diode at D3 around? (Don't forget to turn it back the right way afterward.) • Why does this circuit use a diode at D3 instead of a pull-up resistor? (Meaning, what would happen if a resistor were used instead of the diode?) pressed ( Previous Next 14 Dashboard Calendar To Do Notifications Inbox
1. 1-5 K 30v a. what is tue T CTime constant) ? b. How long will it take for the capacutor TO rtach s0% op charge? C. What is tne voltage of capa citor apter 1 seconds? d. How many tíme constants will it take for the soltage to reach 23 v? C. Gweng that the capacitor is fully changed, how will it take por it to be 20% ? long 120v + BF what is the. T ? b. what is the voltage capacitor apter 10 sec? a. C. How many time constants will it take for Tue Vo Itage to reach 80 v.? d. Given that the capaator is Fully charged, how time constants will it be to reau many GOV!