Question 5) The horizantal cantilever rigid beam AB has no mass and it is supported by an elastic rod at point C. The modulus of elasticity of the BC rod is E=200 GPa with cross-sectional area of A=200 mm’. Calculate the magnitude of the distributed load q acting on the system so that the BC rod can be elongated by 2 mm. -EA 3m rigid B 1.Sm Sm 2m 月

Question 5) The horizantal cantilever rigid beam AB has no mass and it is supported by an elastic rod at point C. The modulus of elasticity of the BC rod is E=200 GPa with cross-sectional area of A=200 mm’. Calculate the magnitude of the distributed load q acting on the system so that the BC rod can be elongated by 2 mm. -EA 3m rigid B 1.Sm Sm 2m 月

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
An axial member consisting of two polymer bars is supported at C as shown. Bar (1) has a cross-sectional area of 680 mm² and an elastic modulus of 29 GPa. Bar (2) has a cross-sectional area of 1580 mm² and an elastic modulus of 15.2 GPa. Determine the deflection of point A relative to support C. 70 KN 0.85 m O -1.902 mm O-2.101 mm O -2.250 mm O-1.354 mm O -2.879 mm 90 kN (1) 90 kN B (2) 1.15 m
A soid, crcular ber ABC consists of two segments, as shown in the figure One segment has a diameter of d,- 56 mm and length of L- 1.40 m; the other segmert has a diameter of d - 48 mm and length of L-1.15 m. what is the alowable torque T in Nm) if the shear stress in not to xceed 30 MPa and the angle of tuat between the ends of the ber is not to enceed 1.207 (Aamume G-B0 GP.) Nm
Q 3. A rigid beam AB is 5.5 m long, hinged at point A and supported by two pipes at C and D as shown in figure 3 below. Pipe 1 at C is of copper has a outer diameter of 120 mm and inner diameter of 100 mm and yield stress of copper is 138 N/mm² Pipe 2 at D is of steel has a outer diameter of 100 mm and inner diameter of 90 mm and yield stress of steel is 250 N/mm2 Calculate the safe load at A if the load factor is 1.66 Pipe 1 Pipe 2 Psafe 2.3 m 2 m C 5.5 m Angle ACE = 0 Figure 3 Angle BDF = 42° Take 0 = 10 Page 7 of 7 PTO
A square plate 2 m on each side is supported by four steel tie rods 6-mm-diameter from an overhead central point as shown in the figure STRM10. The plate supports a surface load of W in kPa. The point of attachment A is 1.25 m above the plane of the plate. 1.25 m 2 m 2 m Determine the maximum load W (kPa) the tie rods can support if the allowable tensile stress on it is 450 MPa. 1) A. 8.43 С. 10.12 В. 12.83 D. 5.64 2) Determine the elongation of each steel tie rod if W = 8.5 kPa. A. 4.28 mm B. 6.46 mm C. 2.84 mm D. 3.54 mm 3) Determine the vertical displacement of the plate. A. 4.28 mm B. 6.46 mm С. 2.84 mm D. None of the above O 1A 1B 10 1D O 2A 28 O 20 O 20 О ЗА O 3B O 30 O 3D
QUESTION 1 The assembly consists of two rods and a horizontal bar BC. Each of the rod AB and CD is made of aluminum and has a cross-sectional area of 125 mm2. A point lqad of 5 kN is applied at point E were located 0.20 m from B. Knowing that they support the rigid member BC, calculate the deflection of point E. Modulus of elasticity for aluminium is 75 GPa. P- 5 kN 0.36 m E B C 0.44 m 0.20 m
The steel truss with E=200GPais loaded as shown in the figure. Determine the following: the following a) the deformation of member AB if the cross-sectional area is 2500mmb) the deformation of member AD if the cross-sectional area is 1800mm A 4.0m 200 KN B D 4.0m 1² 2.5m
STRESSES IN BEAMS Problem 2 The simply supported beam in Fig. (a) has the T-shaped cross section shown. Determine the values and locations of the maximum tensile and compressive bending stresses. 400 lb/ft 1000 lb - 6 in. Į C0.8 in. D A 0.8 in.- 8 in. - 4 ft- Rg = 3400 lb 10 ft R = 1600 lb %3D %3! (a)
A steel cantilever beam 6 m in length is subjected to a concentrated load of 120 N acting at the free end of the bar. The cross section of the beam is shown below. deep. Determine the magnitude and location of the maximum tensile and compressive bending stresses in the beam. As usual, neglect the weight of the beam. 4mm 120 N 1mm 1mm 6mm 6m 1mm 4mm
A rectangular beam is supported at both ends. It carries two concentrated load of 10kN, a clockwise moment of 180kN-m, and a uniformly distributed load "w". The modulus of elasticity of the beam is 140GPa. Solve the following if the reaction at point B is 305.2kN, upward. BEAM DIMENSION: Width = 140mm , Height = 360mm NOTE: b = 4.5m What is the numeric value of C1 (1st Constant)? Determine the deflection at midspan.
Q4) Determine the maximum shear stress acting in the fiberglass beam at the section where the internal shears force is maximum. (tı=15 mm, t2=20 mm, h=150 mm, b=50 mm) 。王! 20 kN/m A |-b-| to 2 m 2 m - 2 m
The center post B of the assembly has an original length of 124.7 mm, whereas posts A and C have a length of 125 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress in each post. The posts are made of aluminum and have a cross-sectional area of 400 mm Eal = 70 GPa. |800 kN/m +100 mm -100 mm A B 125 mm I800 kN/m Answer: 0A = 0c = 189 MPa, oB 21.4 MPа