write please ansers of b,c d,e,f,g only, demonstrate enough please Question 1:.a) Sketch the root locus..b) What are the values of the gain and poles at the imaginary axis crossings:..c) Find the range of the gain making the system stable.......d) Dominant poles are at s1,2 = -1 ±j 3.5, whenk = 8, Find the location of third pole.........e) What is the system type?...f) Find the steady-state errors at k=8,when r(t)= 0.6 u(t) step and 0.6tu(t) ramp inputs areapplied:.........g) Add a Pl controller with k-8 and zero of s=-0.2, find the steady state error at for the sameinputs:..........Ge(s) = k(s + 10) ; Gp(s) =1(s + 1)(s + 2)(s + 6)

Answered: Image /qna-images/answer/e59ab26d-6eab-43a1-bc7e-f2cc32e3553d.jpg

Question 1:...... a) Sketch the root locus. b) What are the values of the gain and poles at the imaginary axis crossings:.. c) Find the range of the gain making the system stable............ d) Dominant poles are at s1,2= -1 ± / 3.5, whenk = 8, Find the location of third pol......... e) What is the system type?........... f) Find the steady-state errors at k=8,when r(t)= 0.6 u(t) step and 0.6tu(t) ramp inputs are applied............ g) Add a PI controller with k=8 and zero of s=-0.2, find the steady state error at for the same inputs:............... 1 ******************

Question 1:...... a) Sketch the root locus. b) What are the values of the gain and poles at the imaginary axis crossings:.. c) Find the range of the gain making the system stable............ d) Dominant poles are at s1,2= -1 ± / 3.5, whenk = 8, Find the location of third pol......... e) What is the system type?........... f) Find the steady-state errors at k=8,when r(t)= 0.6 u(t) step and 0.6tu(t) ramp inputs are applied............ g) Add a PI controller with k=8 and zero of s=-0.2, find the steady state error at for the same inputs:............... 1 ******************

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q1. For the MOSFET circuit below, input is sinusoidal signal of amplitude IV and frequency 50Hz. Find, the DC operating point, Plot the frequency response and Plot the input, output and transfer characteristics and find out the small signal equivalent. Assume an overdrive voltage of 0.2V Use MOSFET 500nm Library file provided. F Vdd=5V -=80 K R1 (1 1.20F
Perform an ac analysis. Represent the amplifier by its ac equivalent circuit and discuss the input resistance at the base and the output resistance. (You can draw the circuit by hand on paper and can paste the image) Determine the minimuuYo uired to put the
in Frequency response, the voltage gain of an amplifier varies with signal .............
I. If a sinusoidal signal voltage of 6V ( pp ) is applied to each amplifier in the figure below , what are their output voltages ( draw ) and what is their phase relationship with respect to the inputs ?
Using the block diagram reduction technique, determine C/R for the block diagram shown below. and verify your result using the signal flow graph.
step by step explanation needed. Given a sinusoidal input signal (1 mV amplitude at 5kHz), design a CE-CC amplifier to achieve a 100 mV amplitude sinusoidal signal across a 50ohm load.
6) Consider the following multistage amplifier. Draw the corresponding small signal model. Label, Vin, Vo1 and Vo. Do NOT make any approximations. Do NOT perform small signal analysis with this model. Just draw the small signal model. Show your work! Vin Vcc malli Q1 Re1 Vo1 Vcc ww1. Rc2 Q2 Re2 Vo
Perform an ac analysis. Represent the amplifier by its ac equivalent circuit and discuss the input resistance at the base and the output resistance. (You can draw the circuit by hand on paper and can paste the image)
Find voltage gain...
Explain the steps that are a- required to use an ideal transformer in order to match a 50o ohm load resistor to a 10ohm source resistor. Mention the other way that can be used to do the matching rather than using an ideal transformer. Which one would you prefer and why ? b- ]Define resonance. Explain how can it be used to enhance the gain of an amplifier. Can we use it for every amplifier circuit ? Why ?
Hello. The answers I got for this are pf distortion = .83 and pf total of 0.7. I'm not sure I did it right though and I was hoping to compare answers and see how you go through this. Thank you.
The term duty cycle refers to the amount of time a signal is complete cycle. A. off compared to the period of one B. on The output voltage of op-amp is positive saturation, when the voltage applied to the input is greater than the input. A. inverting B. noninverting A square wave that is 20V at its high state and OV when it is off will produce an average DC when its duty cycle is 75%. Formula: VOUT = Duty Cycle * Peak voltage voltage of A. 7.5V B. 10V C. 15V