Q4. Design a DSB-SC modulator to generate a signal, k m(t) cos(2ax(300)x(10')t). The following equipments are available in the stock room: i) a signal generator of frequency 100 kHz; ii) a ring modulator and transformers; iii) a BPF tuned to 300 kHz; iv) a LPF with feutoff fm arired signal and find the value of constant k?

Q4. Design a DSB-SC modulator to generate a signal, k m(t) cos(2ax(300)x(10')t). The following equipments are available in the stock room: i) a signal generator of frequency 100 kHz; ii) a ring modulator and transformers; iii) a BPF tuned to 300 kHz; iv) a LPF with feutoff fm arired signal and find the value of constant k?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What types of PWM is shown in the figure? * Modulating Waveform Carrier waveform A (b) 44444 F -V O Unipolar O Bipolar 000
(a) Plot the even and odd parts of the signal of Figure
Q4. For the C.R.O. square voltage waveform shown in Figure determine (a) the periodic time, (b) the frequency and (c) the peak-to-peak voltage. The 'time/cm' (or timebase control) switch is on 100 µs/cm and the 'volts/cm' (or signal amplitude control) switch is on 20V/cm.
Show the downward shift of the output signal with the series capacitor and diode. Clampers or DC restorers are clamp a peak of a waveform to a specific DC level compared with a capacitively coupled signal which swings about its average DC level (usually 0V). If the diode is removed from the clamper, it defaults to a simple coupling capacitor– no clamping. What is the clamp voltage? And, which peak gets clamped? Why is this so? Produce a schematic diagram with LTspice schematic capture program. Voltage values: Capasitor value: 1000 pF DC offset: 0 V Amplitude: 5 V Freq: 1 KHz
For the C.R.O. square voltage waveform shown in Figure determine (a) the periodic time, (b) the frequency and (c) the peak-to-peak voltage. The 'time/cm' (or time base control) switch is on 100 us/cm and the 'volts/cm' (or signal amplitude control) switch is on 20 V/cm.
Draw the signal after adding -2.5 DC level with the given signal, sketch the new output signal and draw the required circuit and briefly specify the function of the circuit also name this phenomenon. 10
For the C.R.O sine waveform shown in figure, determine (a) periodic time, (b) frequency, (c) Amplitude, and (d) peak-to-peak voltage. The 'time/cm' switch is on 85 us/cm and the volts/cm' switch is on 65 V/cm.
12- A DVM measure... a- peak value. b- RMS value. Average value. d- peak to peak value. 13 The study of energy distribution across the frequency spectrum of a given electrical signal is done by a Distortion meter b-wave analyzer.
why is the piv rating important for IS AN AC CIRCUIT THAT CONVERTS AC SIGNAL TO DC SIGNAL
e average voltage of Vo. 5 URM U 2 Figure B.2 shows a circuit using two silicon diodes with knee voltage of 0.7 V. The supply voltage, Vs, is a sinusoidal AC signal. The produced output, Vo, is a fluctuating DC signal with ripple peak-to-peak voltage of I.58 V. & UTM UTM UTM STM DI 5 UTM O UTM 50 Hz &UTM UTM UTM 5 UTM UTM UTM 50 µF RL UTM & UTM D2 &UTM/ UTMTUTM (a) Determine the SITM (b) Determine the peak voltage of the Vs. 5 UTM (c) Consider UTM &UTM & UTM waveform of Vo with complete labelling. en Ci is removed from the circuit (i.e. open circuit). Draw the 5 UTM & UTM UTM U1 A TM 5 UTM UTM TM 5 UTM UTM
1)to VRMs value to generate a signal with a peak voltage of 10 V with a signal generator in a multisim program..................... must be entered. 2)) the frequency of the signal generator to produce a signal with a period of 10ms...................... must be entered as. What should come to the dotted line?
Advantages of improvement of transient stability by using waveform relaxation method