Q4) A three phase 60-Hz transmission line is 130-mile long. The receiving end power is 80 MW, 0.87 lagging power factor at 180 KV and the sending end voltage is 230KV, 0.92 lagging power factor, the load angle is 11.5° and the line efficiency is 89%. Calculate ABCD transmission matrix, and voltage regulation. 180 T 113

Q4) A three phase 60-Hz transmission line is 130-mile long. The receiving end power is 80 MW, 0.87 lagging power factor at 180 KV and the sending end voltage is 230KV, 0.92 lagging power factor, the load angle is 11.5° and the line efficiency is 89%. Calculate ABCD transmission matrix, and voltage regulation. 180 T 113

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16MCQ: With generator conyention, where the current leaves the positive terminal of the circuit element, if...

See similar textbooks

Similar questions

A high-voltage direct-current generating station delivers power to a city. The generator output voltage is Vo = 400 kV, the city is represented by resistance RL = 1749 ohms, and each wire of the transmission line round-trip between the station and city is represented by resistance RTL = 159 ohms. What percentage of total power supplied by the generating station is consumed by the transmission line? Vo RTL M RTL M RL (city)
H* 3G zain IQ Asiacell The generator convert from PV to PQ if the active power of the generator exceed the * maxinum and minimum limits between the maximum and mimium limit equal to the load power Non of them With base voltage of 450 kV. The actual voltage of the generator is 560 kV. The magnitude voltage in the parameter of the PV generator in the nepaln software is * O 1.2444 pu O 450 kV O 124.44 % O 0.8036 pu 80.36 % Non of them
The actual power flow on the transmission line is 1.25 pu and the voltage at both busbars is 1.0 pu. The system frequency is 60 Hz. The power flow is estimated using the phase difference between busbars 1 and 2, that is using ol -2. The actual value of ol -2=38.6822 deg. The measurement of the phase angle ol has a time stamp error of 0.1 ms and that of the phase angle 92 is 0.2ms. Calculate the error in the estimated power flow. Bus 1 Bus 2 PMU I j0.5 V= 1.0 PMU 2 V;= 1.0
The length of a three-phase power transmission line with a nominal operating voltage of 69 kV is 16km. The impedance of the transmission line per unit length is 0.125 + j0.4375 ohm/ km. At the end of the line, a 70 MVA star connected load with a power factor of 0.8 back under 69 kV interphase voltage is fed. Capacitive circuit element with a capacitance of 19.14 mikro F / phase is placed as shunt at the end of the transmission line. According to these given; a) Line head voltage and current, b) Calculate the active and reactive power per line.
A 5 km long, 3-phase 34.5 kV line has a horizontal configuration of 4 ft. spacing. The conductor is 336.4 ACSR with GMR of 0.0244. What is the inductance of the line? * A. 7.63 mH B. 4.76 mH C. 5.33 mH D. 6.49 mH
A 100 km long three phase transmission line has resistance 12Ω per phase, inductance per phase 0.15 Hanni, capacitance between each phase and neutral 0.8uF. At the far end a load of 30 MW at 110 kV, 50 Hz frequency is connected at 0.8 power factor. So ( 1 ) sending end voltage ( 2 ) sending end current
A 3- q, 50-Hz generating station supplies a load of 14500 kW at 0.6 (lag) through a short overhead transmission line. The resistance per km is 15 Q and inductance 45 mH. Determine the sending-end voltage if the receiving-end voltage is 77 kV and also the loss of transmission. Inductive Reactance Line Current Sending End Voltage Loss in Transmission Line Windows buis
1. A single phase, 60Hz, 200-km medium nominal-T transmission line receives 10 MW at 0.95 lagging pf at 69 kV from the generator. Using circuit analysis, determine: i. Receiving-end Real, Reactive, and Apparent Power ii. Power loss (real component) in the transmission Is 3.60 j30Ω CS Scanned with CamScanner 2.8Ω M j40Ω j0.000842 O Z VR
2. A three-phase transmission line has parameters Xc-6 k 2, R-3.25 2 and X₁-25 92, and delivers 300 MW to a load with both ends of the line at 230 kV. Draw a pi equivalent per-phase circuit of the line. On a per-phase basis, calculate the active power delivered to the load, the reactive power of the line and the active power delivered by the source. Based on these calculations can the equivalent circuit be simplified further?
3. A 132 kV, 50 Hz, 3-phase transmission line delivers a load of 50 MW at 0-8 p.f. lagging at the receiving end. The generalized constants of the transmission line are : A = D = 0-95 1-4°; B = 96 278° ; C = 0.0015 290°.Find the regulation and charging %3D %3D current. Use Nominal-T method. etanco 3AT 758019 +240.06)
A workshop from a 231/400 V transformer center with a 3-phase and four-conductor underground cablefed. The resistance of the phase conductors is 0.035 ohms and the resistance of the neutral conductors is 0.05 ohms.25 kVA at 0.8 reverse power factor from R phase of the supply line, 0.8 forward power factor from S phase 15Fully ohmic loads of 10 kVA are drawn from kVA and T phases.(a) Find the currents flowing through the phase conductors and neutral conductors.(b) Voltage drops between the transformer substation and the workshop and at the load terminals.calculate the voltages(c) Plot the supply line currents and phase voltages phasorally.
With generator conyention, where the current leaves the positive terminal of the circuit element, if P is positive then positive real power is delivered. (a) False (b) True