15₁ Q2// The air supplied to a gas turbine plant is 10 kg/s. The pressure ratio is 6 and pressure at the inlet to the compressor is l'bar. The compressor is two stages and provided with perfect intercooler. The inlet temperature is 300 K and the maximum temperature is limited to 1073 K. the isentropic efficiency of compressor each stage is 80%. The isentropic efficiency of turbine is 85%. A regenerator is included in plant whose effectiveness is 0.7. Neglect the mass of fuel. Determine the thermal efficiency of the plant. ६ Inter cooler 12:41 Tri Tu с L.P. Air in 0 с H.P. Exhaust Regenerator 3-6 supply Alternator B₁= & Bu

15₁ Q2// The air supplied to a gas turbine plant is 10 kg/s. The pressure ratio is 6 and pressure at the inlet to the compressor is l'bar. The compressor is two stages and provided with perfect intercooler. The inlet temperature is 300 K and the maximum temperature is limited to 1073 K. the isentropic efficiency of compressor each stage is 80%. The isentropic efficiency of turbine is 85%. A regenerator is included in plant whose effectiveness is 0.7. Neglect the mass of fuel. Determine the thermal efficiency of the plant. ६ Inter cooler 12:41 Tri Tu с L.P. Air in 0 с H.P. Exhaust Regenerator 3-6 supply Alternator B₁= & Bu

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A turbojet aircraft moving with a velocity of 790 ft/s at a runway where the pressure& temperature is found to be 14.7psi & 546R. The axial flow compressor provides apressure ratio of 14 to 1. Temperature at the turbine inlet is 2000R. The mass flowrate of airinside the engine is 133 lbm/s. Determine the following:a. T-S diagramb. Pressure & temperature at each statec. Thrust force (lbf)d. Propulsive power developed (BTU/min)e. Propulsive Efficiency
An R22 system has compression raito of 4:9:1 NRE of 72 btu/pd , heat compression of 18 btu/ pd and constant volume of 1.4 cfm at inlet to the compressor . what's the displacement of compressor for 1 ton of refrigerant.
.A two-stage compressor takes air at 100kpa and 25C with volume flow of 0.123m3/s and discharges to 700kpa. What is the heat rejected by the intercooler? A. 12.45kw B. 13.73kw C. 45.34kw D. 32.34kw
Consider a 10:1 pressure rise in the ideal compressor with air as the working fluid compared to the a pump with water as the working fluid and the same pressure rise and same inlet pressure. Check all that apply The compreesor takes 300 times more work/unit mass as the pump The work per unit mass is about the same between the two. Becase the pump deals iwth a liquid the work will be higher. The compressor in a Brayton cycle has a much greater effect on performance than a pump in a Rankine cycle.
In a marine gas turbine unit, a high-pressure stage turbine drives the compressor and a low-pressure stage turbine drives the propeller through suitable gearing. The overall pressure ratio is 4/1 and the maximum temperature is 650 o the isentropic efficiencies of the compressor, H. P. turbine, L. P. turbine are 0.8, 0.83 and 0.85 respectively and the mechanical efficiency of both shafts is 98 %. Sketch the process on the T-s diagram i. Calculate the pressure between turbine stages when the air intake conditions are 1.01 bar and 25 oC. ii. Calculate also the thermal efficiency and the shaft power when the mass flow is 60 kg/s. NB: Neglect kinetic energy changes and the pressure loss in combustion.
4. The open cycle gas turbine operate on Brayton cycle with pressure ratio 4.5/1. Air enter the compressor at 210C and heated to 7800C at entry to the turbine. If mass flow rate is 140kg/min, Determine: a. e b. Wnet
no. 3 question: A diesel engine powers a boat. The engine’s cylinders each have a compression ratio (Vmax/Vmin) of 12 and the Vmax is 4ft3. If 1 cylinderis in the isobaric compression stroke, find the final temperature if the initial temperature is 540F Main question: From number 3, if the gas tankaccident happened on top of Mt. Everest’s summit where patm is only 33.7 kpa and the readings obtained are the same, find the new finaltemperature
It is desired to increase the compression ratio of spark ignition engine for 8 to 10. Assuming a ratio of constant pressure to constant volume specific heat to be 1.3, what will happen to the effeciency of the engine.?
Q2/Gas turbine unit having heat exchanger with thermal ratio(0.75),ahigh pressure stage turbine drives the compressor and a low pressurestage turbine generate the power. The overall pressure ratio is (5/1) andthe maximum temperature is (1000 o c).The isentropic efficiencies ofcompressor, H.P.T and L.P.T are (0.7),(0.78) and (0.8) respectively andmechanical efficiency of both shafts is (99 %) . Calculate:a- The pressure between turbine stages when the air intake conditionare (1 bar) and (29 oc) b- Thermal efficiency when the mass flow is (30 kg/sec)Cpg= 1.15 kJ/kg.K ɣg=1.33
In a marine gas turbine unit, a high-pressure stage turbine drives the compressor and a low-pressure stage turbine drives the propeller through suitable gearing. The overall pressure ratio is 4/1 and the maximum temperature is 650 oC. the isentropic efficiencies of the compressor, H. P. turbine, L. P. turbine are 0.8, 0.83 and 0.85 respectively and the mechanical efficiency of both shafts is 98 %. Sketch the process on the T-s diagram Calculate the pressure between turbine stages when the air intake conditions are 1.01 bar and 25 oC. Calculate also the thermal efficiency and the shaft power when the mass flow is 60 kg/s. NB: Neglect kinetic energy changes and the pressure loss in combustion.
An ideal reheat turbine with one stage of reheat receives steam at 8.0 MPa, 480 o C. Reheatpressure is 0.83 MPa and exhaust pressure is 0.007 MPa. The work is 1559 kJ/kg and the thermalefficiency is 41.05%. Find the temperature of steam leaving the reheater. (3 decimal in final answer pls)
A trubo-charge, 16 cylinder, vee-type diesel engine has an air comsumpyion of 3000 kg/hr per cylinder at rate load and speed. this air is drawn in through a filter by a centrifugal compressor directly connected to the exhaust gas turbine. the temperature of the air from the compressor to 145 C and a counter flow air cooler reduced the air temperature to 45 C. before it goes to the engine suction header. cooling water enters air at 30 C and leaves at 38 C. calculate the quantity of the cooling water in m/hr required to cool the total air requirement of the engine at rate load and speed. ( hint: use AMTD)